HP 10500 Series Configuration Manual page 32

[PE1] bgp 200
[PE1-bgp] ip vpn-instance vpn1
[PE1-bgp-vpn1] peer 30.1.1.1 as-number 100
[PE1-bgp-vpn1] ipv4-family
[PE1-bgp-ipv4-vpn1] peer 30.1.1.1 enable
[PE1-bgp-ipv4-vpn1] quit
[PE1-bgp-vpn1] quit
[PE1-bgp] quit
# On PE 1, display the routing information of VPN instance vpn1.
[PE1] display ip routing-table vpn-instance vpn1
Destinations : 13
Destination/Mask
0.0.0.0/32
30.1.1.0/24
30.1.1.0/32
30.1.1.2/32
30.1.1.255/32
127.0.0.0/8
127.0.0.0/32
127.0.0.1/32
127.255.255.255/32
192.168.0.0/24
224.0.0.0/4
224.0.0.0/24
255.255.255.255/32
# Perform similar configuration on the MCE and PE 1 for VPN 2. Redistribute the OSPF routes of
VPN instance vpn2 into the EBGP routing table. (Details not shown.)
The following output shows that PE 1 has learned the private route of VPN 2 through BGP:
[PE1] display ip routing-table vpn-instance vpn2
Destinations : 13
Destination/Mask
0.0.0.0/32
40.1.1.0/24
40.1.1.0/32
40.1.1.2/32
40.1.1.255/32
127.0.0.0/8
127.0.0.0/32
127.0.0.1/32
127.255.255.255/32
192.168.10.0/24
224.0.0.0/4
224.0.0.0/24
255.255.255.255/32
Routes : 13
Proto Pre Cost
Direct 0 0
Direct 0 0
Direct 0 0
Direct 0 0
Direct 0 0
Direct 0 0
Direct 0 0
Direct 0 0
Direct 0 0
BGP 255 3
Direct 0 0
Direct 0 0
Direct 0 0
Routes : 13
Proto Pre Cost
Direct 0 0
Direct 0 0
Direct 0 0
Direct 0 0
Direct 0 0
Direct 0 0
Direct 0 0
Direct 0 0
Direct 0 0
BGP 255 3
Direct 0 0
Direct 0 0
Direct 0 0
26
NextHop Interface
127.0.0.1 InLoop0
30.1.1.2 Vlan30
30.1.1.2 Vlan30
127.0.0.1 InLoop0
30.1.1.2 Vlan30
127.0.0.1 InLoop0
127.0.0.1 InLoop0
127.0.0.1 InLoop0
127.0.0.1 InLoop0
30.1.1.1 Vlan30
0.0.0.0 NULL0
0.0.0.0 NULL0
127.0.0.1 InLoop0
NextHop Interface
127.0.0.1 InLoop0
40.1.1.2 Vlan40
40.1.1.2 Vlan40
127.0.0.1 InLoop0
40.1.1.2 Vlan40
127.0.0.1 InLoop0
127.0.0.1 InLoop0
127.0.0.1 InLoop0
127.0.0.1 InLoop0
40.1.1.1 Vlan40
0.0.0.0 NULL0
0.0.0.0 NULL0
127.0.0.1 InLoop0