Sending Video Image To Personal Computer - Mitsubishi Electric GOT1000 Series Connection Manual

14.2.2 Sending video image to personal computer

Video camera,
Microphone,
Speaker
Connection cable 1)
Multimedia Signal
controller type
Model name
Coaxial
NTSC
*5
connection
/PAL
diagram 1)
*1 The cable length differs depending on the specification of the video camera used by the user.
*2 The destination connected with the twisted pair cable varies with the configuration of the applicable Ethernet network system.
Connect to the Ethernet module, hub, transceiver, wireless LAN adapter (NZ2WL-JPA or NZ2WL-JPS), or other system
equipment corresponding to the applicable Ethernet network system.
Use cables, connectors, and hubs that meet the IEEE802.3 10BASE-T/100BASE-TX standards.
For the controllers that can be connected to the wireless LAN adapters and how to set the wireless LAN adapter, refer to the
manual of the wireless LAN adapter used.
*3 When connecting GT16 of the function version A to an equipment that meets the 10BASE (-T/2/5) standard, use the switching
hub and operate in a 10Mbps/100Mbps mixed environment.
For how to check the function version, refer to the following.
*4 For the CF card to be inserted into the multimedia unit, refer to the following.
• Type of CF card that can be inserted
• Precautions for using the CF card
*5 For the type of the video camera that can be connected, refer to the following Technical News.
*6 Install the multimedia interaction tool before use.
For details of the multimedia interaction tool, refer to the following manual.
*7 GT1675-VN, GT1672-VN, and GT1662-VN cannot be used.
*8 A length between a hub and a node.
The maximum distance differs depending on the Ethernet device to be used.
The following shows the number of the connectable nodes when a repeater hub is used.
• 10BASE-T: Max. 4 nodes for a cascade connection (500m)
• 100BASE-TX: Max. 2 nodes for a cascade connection (205m)
When switching hubs are used, the cascade connection between the switching hubs has no logical limit for the number of
cascades.
For the limit, contact the switching hub manufacturer.
POINT POINT POINT
Power supply of video camera
Depending on the video camera type, noises from the power supply cable of the camera may cause a malfunction
on the PLC or the GOT. In this case, apply the following line filter to the power line of the camera.
Recommended line filter: TDK ZHC2203-11 (or equivalent)
Connection cable 1)
interface 1)
*2*3
GOT
Max. Option device
Model
distance (Interface 1))
*4
*1
GT16M-MMR
*7
GT16 User's Manual (Hardware)
List of valid devices applicable for GOT1000 series (GOT-A-0010)
14.4 GOT Side Settings
List of valid devices applicable for GOT1000 series (GOT-A-0010)
GT Designer3 Version1 Screen Design Manual
Extended function OS
Multimedia
GOT
Connection cable 2)
interface 2)
Connection cable 2)
Option device
Cable model
(Interface 2))
Ethernet Twisted pair cable
• 10BASE-T
Interface
Shielded twisted
(Built into GOT)
pair cable (STP) or
unshielded twisted
pair cable (UTP):
Category 3, 4, and 5
GT16M-MMR
• 100BASE-TX
Shielded twisted pair
cable (STP):
Category 5 and 5e
14. MULTIMEDIA CONNECTION
14.2 System Configuration
Communication driver
Option OS
Connection type
Gateway (FTP)
dependent
PC
Number of
Personal
Maximum
connectable
computer
segment
equipment
*6
*8
length
To be
1 multimedia
selected
100m controller for 1
by the
GOT
user.
9
10
11
12
13
14
15
14 - 3