GE C70 Instruction Manual page 71

CHAPTER 3: INSTALLATION
When current monitoring is used to seal-in the form-A and solid-state relay contact outputs, give the
FlexLogic operand driving the contact output a reset delay of 10 ms to prevent damage of the output
contact (in situations when the element initiating the contact output is bouncing, at values in the
region of the pickup value).
For high-density input/output modules 6W and 6X, use the following guidelines to connect:
2
• 12 to 24 AWG (3.3 mm to 0.2 mm
2
• 16 to 24 AWG (1.31 mm
maximum per circuit.
• Suggested wiring screw tightening torque is a minimum 4.43 in-lb (0.5 Nm) and maximum 5.31 in-lb (0.6 Nm)
• Minimum suggested temperature rating for the conductors is 75°C
• Wire type: copper
• Do not use with SL power supply module
Table 3-3: Contact input and output module assignments
~6A module
Terminal Output or
assignment input
~1 Form-A
~2 Form-A
~3 Form-C
~4 Form-C
~5a, ~5c 2 Inputs
~6a, ~6c 2 Inputs
~7a, ~7c 2 Inputs
~8a, ~8c 2 Inputs
~6E module
Terminal Output or
assignment input
~1 Form-C
~2 Form-C
~3 Form-C
~4 Form-C
~5a, ~5c 2 Inputs
~6a, ~6c 2 Inputs
~7a, ~7c 2 Inputs
~8a, ~8c 2 Inputs
~6K module
Terminal Output
assignment
~1 Form-C
~2 Form-C
~3 Form-C
~4 Form-C
~5 Fast Form-C
C70 CAPACITOR BANK PROTECTION AND CONTROL SYSTEM – INSTRUCTION MANUAL
2
), single wire termination
2
to 0.2 mm ), multiple wire termination with matching wire sizes and stranding. Two wires
~6B module
Terminal Output or
assignment input
~1 Form-A
~2 Form-A
~3 Form-C
~4 Form-C
~5 Form-C
~6 Form-C
~7a, ~7c 2 Inputs
~8a, ~8c 2 Inputs
~6F module
Terminal Output
assignment
~1 Fast Form-C
~2 Fast Form-C
~3 Fast Form-C
~4 Fast Form-C
~5 Fast Form-C
~6 Fast Form-C
~7 Fast Form-C
~8 Fast Form-C
~6L module
Terminal Output or
assignment input
~1 Form-A
~2 Form-A
~3 Form-C
~4 Form-C
~5a, ~5c 2 Inputs
~6C module
Terminal Output
assignment
~1 Form-C
~2 Form-C
~3 Form-C
~4 Form-C
~5 Form-C
~6 Form-C
~7 Form-C
~8 Form-C
~6G module
Terminal Output or
assignment input
~1 Form-A
~2 Form-A
~3 Form-A
~4 Form-A
~5a, ~5c 2 Inputs
~6a, ~6c 2 Inputs
~7a, ~7c 2 Inputs
~8a, ~8c 2 Inputs
~6M module
Terminal Output or
assignment input
~1 Form-A
~2 Form-A
~3 Form-C
~4 Form-C
~5 Form-C
WIRING
~6D module
Terminal Output
assignment
~1a, ~1c 2 Inputs
~2a, ~2c 2 Inputs
~3a, ~3c 2 Inputs
~4a, ~4c 2 Inputs
~5a, ~5c 2 Inputs
~6a, ~6c 2 Inputs
~7a, ~7c 2 Inputs
~8a, ~8c 2 Inputs
~6H module
Terminal Output or
assignment input
~1 Form-A
~2 Form-A
~3 Form-A
~4 Form-A
~5 Form-A
~6 Form-A
~7a, ~7c 2 Inputs
~8a, ~8c 2 Inputs
~6N module
Terminal Output or
assignment input
~1 Form-A
~2 Form-A
~3 Form-A
~4 Form-A
~5a, ~5c 2 Inputs
3-21
3