Sfp Repair - HP 3PAR StoreServ 7000 Service Manual

SFP Repair

The SFP is located in the port on the controller node HBA/CNA and there are two to four SFPs per
node.
Before you begin, use either SPmaint or the HP 3PAR Management Console to identify the failed
SFP:
To perform maintenance using CLI, access SPmaint:
1. In the 3PAR Service Processor Menu, select option 7 Interactive CLI for an InServ.
2. Issue the following commands:
showport to view the port State:
s750 cli%showport
N:S:P
Label Partner FailoverState
0:0:1 initiator
-
0:0:2 initiator
-
0:1:1
-
0:1:2
-
0:2:1
-
0:2:2
-
0:3:1
-
1:0:1 initiator
-
1:0:2 initiator
-
1:1:1
-
1:1:2
-
1:2:1 initiator loss_sync 2FF70002AC0185A6 21210002AC0185A6 free
-
1:2:2 initiator loss_sync 2FF70002AC0185A6 21220002AC0185A6 free
-
1:2:3 initiator loss_sync 2FF70002AC0185A6 21230002AC0185A6 free
-
1:2:4 initiator loss_sync 2FF70002AC0185A6 21240002AC0185A6 free
-
1:3:1
-
showport -sfp to verify which SFP requires replacement:
cli%showport -sfp
N:S:P -State- -Manufacturer- MaxSpeed(Gbps) TXDisable TXFault RXLoss DDM
0:1:1 OK
0:1:2 OK
0:2:1 OK
0:2:2 OK
1:1:1 OK
1:1:2 -
1:2:1 OK
1:2:2 OK
Mode State
ready 50002ACFF70185A6 50002AC0010185A6 disk
- -
ready 50002ACFF70185A6 50002AC0020185A6 disk
- -
target ready 2FF70002AC0185A6 20110002AC0185A6 host
- -
target ready 2FF70002AC0185A6 20120002AC0185A6 host
- -
target loss_sync
- -
target loss_sync
- -
peer offline
-
ready 50002ACFF70185A6 50002AC1010185A6 disk
- -
ready 50002ACFF70185A6 50002AC1020185A6 disk
- -
target ready 2FF70002AC0185A6 21110002AC0185A6 host
- -
target loss_sync 2FF70002AC0185A6 21120002AC0185A6 free
- -
- -
- -
- -
- -
peer offline
-
HP-F
HP-F
AVAGO
AVAGO
HP-F
-
HP-F
HP-F
Node_WWN Port_WWN/HW_Addr Type Protocol
- 2C27D75301F6
- 2C27D75301F2
- 0002AC8004DB
- 0002AC8004BD
8.5 No
8.5 No
10.3 No
10.3 No
8.5 No
- -
8.5 No
8.5 No
SAS
SAS
FC
FC
iscsi iSCSI
iscsi iSCSI
rcip IP RCIP0
SAS
SAS
FC
FC
FC
FC
FC
FC
rcip IP RCIP1
No No Yes
No No Yes
No Yes Yes
No Yes Yes
No No Yes
- - -
No Yes Yes
No Yes Yes
SFP Repair 15