Siemens Micromaster 440 Operating Instructions Manual page 77

Issue 12/02
Par. No.
P1740
r1751
P1750[3]
P1755[3]
P1756[3]
P1758[3]
P1759[3]
P1764[3]
r1770
r1771
r1782
P1780[3]
r1787
P2480[3]
P2481[3]
P2482[3]
P2484[3]
r2489
P2487[3]
P2488[3]
Communication (P0004 = 20)
Par. No.
P0918
P0927
r0965
r0967
r0968
r0964[5]
P0971
P2000[3]
P2001[3]
P2002[3]
P2003[3]
r2004[3]
P2009[2]
P2010[2]
P2011[2]
P2012[2]
P2013[2]
P2014[2]
r2015[8]
P2016[8]
r2018[8]
r2024[2]
MICROMASTER 440 Operating Instructions
6SE6400-5AW00-0BP0
Parametername
Gain for oscillation damping
Status word of motor model
Control word of motor model
Start-freq. motor model (SLVC)
Hyst.-freq. motor model (SLVC)
T(wait) transit to feed-fwd-mode
T(wait) for n-adaption to settle
Kp of n-adaption (SLVC)
CO: Prop. output of n-adaption
CO: Int. output of n-adaption
Output of Rs-adaptation
Control word of Rs/Rr-adaption
Output of Xm-adaption
Position mode
Gearbox ratio input
Gearbox ratio output
No. of shaft turns = 1 Unit
Act. number of shaft revolutions
Positional error trim value
No. final shaft turns = 1 Unit
Parametername
CB address
Parameter changeable via
Profibus profile
Control word 1
Status word 1
Firmware version data
Transfer data from RAM to EEPROM
Reference frequency
Reference voltage
Reference current
Reference torque
Reference power
USS normalization
USS baudrate
USS address
USS PZD length
USS PKW length
USS telegram off time
CO: PZD from BOP link (USS)
CI: PZD to BOP link (USS)
CO: PZD from COM link (USS)
USS error-free telegrams
5 System parameters
Default Level DS
0.000 3 CUT
- 3 -
1 3 CUT
5.0 3 CUT
50.0 3 CUT
1500 3 CUT
100 3 CUT
0.2 3 CUT
- 3 -
- 3 -
- 3 -
3 3 CUT
- 3 -
1 3 CT
1.00 3 CT
1.00 3 CT
1.0 3 CUT
- 3 -
0.00 3 CUT
1.0 3 CUT
Default Level DS
3 2 CT
15 2 CUT
- 3 -
- 3 -
- 3 -
- 3 -
0 3 CUT
50.00 2 CT
1000 3 CT
0.10 3 CT
0.75 3 CT
- 3 -
0 3 CT
6 2 CUT
0 2 CUT
2 3 CUT
127 3 CUT
0 3 CT
- 3 -
52:0 3 CT
- 3 -
- 3 -
QC
N
-
N
N
N
N
N
N
-
-
-
N
-
N
N
N
N
-
N
N
QC
N
N
-
-
-
-
N
N
N
N
N
-
N
N
N
N
N
N
-
N
-
-
77