Siemens Micromaster 440 Operating Instructions Manual page 79

Issue 12/02
Par. No.
P2163[3]
P2164[3]
P2165[3]
P2166[3]
P2167[3]
P2168[3]
r2169
P2170[3]
P2171[3]
P2172[3]
P2173[3]
P2174[3]
P2176[3]
P2177[3]
P2178[3]
P2179
P2180
P2181[3]
P2182[3]
P2183[3]
P2184[3]
P2185[3]
P2186[3]
P2187[3]
P2188[3]
P2189[3]
P2190[3]
P2192[3]
r2197
r2198
PI Controller (P0004 = 22)
Par. No.
P2200[3]
P2201[3]
P2202[3]
P2203[3]
P2204[3]
P2205[3]
P2206[3]
P2207[3]
P2208[3]
P2209[3]
P2210[3]
P2211[3]
MICROMASTER 440 Operating Instructions
6SE6400-5AW00-0BP0
Parametername
Entry freq. for perm. deviation
Hysteresis frequency deviation
Delay time permitted deviation
Delay time ramp up completed
Switch-off frequency f_off
Delay time T_off
CO: Act. filtered frequency
Threshold current I_thresh
Delay time current
Threshold DC-link voltage
Delay time DC-link voltage
Torque threshold T_thresh
Delay time for torque threshold
Delay time for motor is blocked
Delay time for motor pulled out
Current limit for no load ident.
Delay time for no load ident.
Belt failure detection mode
Belt threshold frequency 1
Belt threshold frequency 2
Belt threshold frequency 3
Upper torque threshold 1
Lower torque threshold 1
Upper torque threshold 2
Lower torque threshold 2
Upper torque threshold 3
Lower torque threshold 3
Time delay for belt failure
CO/BO: Monitoring word 1
CO/BO: Monitoring word 2
Parametername
BI: Enable PID controller
Fixed PID setpoint 1
Fixed PID setpoint 2
Fixed PID setpoint 3
Fixed PID setpoint 4
Fixed PID setpoint 5
Fixed PID setpoint 6
Fixed PID setpoint 7
Fixed PID setpoint 8
Fixed PID setpoint 9
Fixed PID setpoint 10
Fixed PID setpoint 11
5 System parameters
Default Level DS
3.00 2 CUT
3.00 3 CUT
10 2 CUT
10 2 CUT
1.00 3 CUT
10 3 CUT
- 2 -
100.0 3 CUT
10 3 CUT
800 3 CUT
10 3 CUT
5.13 2 CUT
10 2 CUT
10 2 CUT
10 2 CUT
3.0 3 CUT
2000 3 CUT
0 2 CT
5.00 3 CUT
30.00 2 CUT
50.00 2 CUT
99999.0 2 CUT
0.0 2 CUT
99999.0 2 CUT
0.0 2 CUT
99999.0 2 CUT
0.0 2 CUT
10 2 CUT
- 2 -
- 2 -
Default Level DS
0:0 2 CUT
0.00 2 CUT
10.00 2 CUT
20.00 2 CUT
30.00 2 CUT
40.00 2 CUT
50.00 2 CUT
60.00 2 CUT
70.00 2 CUT
80.00 2 CUT
90.00 2 CUT
100.00 2 CUT
QC
N
N
N
N
N
N
-
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
-
-
QC
N
N
N
N
N
N
N
N
N
N
N
N
79