Page 1 "FD 100/320Gbps NT and FX NT IHub System Basics, Management and OAM Guide" 7302 Intelligent Services Access Manager 7330 Intelligent Services Access Manager FTTN 7360 Intelligent Services Access Manager FX Released 5.6 "FD 100/320Gbps NT and FX NT IHub System Basics, Management and OAM Guide"...
Page 2 © 2014-2017 Nokia. Contains proprietary/trade secret information which is the property of Nokia and must not be made available to, or copied or used by anyone outside Nokia without its written authorization. Not to be used or disclosed except in accordance with applicable agreements.
Page 3: Table Of Contents
"FD 100/320Gbps NT and FX NT IHub System Basics, Management and OAM Guide" Table of contents Preface...................19 Scope ......................19 Audience....................19 Required knowledge..................19 Product naming ..................19 Documents ....................19 Acronyms and initialisms ................19 Safety information..................20 Special information ..................20 Release notes....................20 Introduction...................21 Contents ....................21 CLI Command Syntax Symbols..............21 System Management ..............23 In this Chapter ...................23...
Page 4 "FD 100/320Gbps NT and FX NT IHub System Basics, Management and OAM Guide" 3.5.3.5 server......................35 3.5.3.6 user-user-hairpin ..................36 3.5.3.7 vlan-dot1q-etype..................36 3.5.3.8 core1-uptime....................36 3.5.3.9 ipv6-prefix-mgmt..................37 3.5.3.10 dst-ip......................37 3.5.3.11 src-ip......................37 3.5.4 Clear Commands..................38 3.5.4.1 alarm......................38 Security..................41 Security Features ..................41 4.1.1 Encryption....................41 4.1.2 TCP Enhanced Authentication Option............41 4.1.2.1 Packet Format ...................42...
Page 5 "FD 100/320Gbps NT and FX NT IHub System Basics, Management and OAM Guide" 4.4.2.19 shutdown ....................61 4.4.2.20 ipv6-filter ....................61 4.4.2.21 entry......................62 4.4.2.22 action ......................62 4.4.2.23 match......................62 4.4.2.24 dscp ......................63 4.4.2.25 dst-ip......................64 4.4.2.26 dst-port ......................64 4.4.2.27 icmp-code ....................65 4.4.2.28 icmp-type ....................65 4.4.2.29 router ......................65 4.4.2.30...
Page 6 "FD 100/320Gbps NT and FX NT IHub System Basics, Management and OAM Guide" 5.3.3.1 port ......................84 5.3.4 Router Commands ..................86 5.3.4.1 router ......................86 5.3.4.2 neighbor.....................87 5.3.4.3 statistics.....................88 5.3.4.4 session ......................91 5.3.4.5 statistics.....................94 5.3.4.6 interface.....................96 5.3.4.7 neighbor....................100 5.3.4.8 neighbor....................102 5.3.5 Service Commands .................102 5.3.5.1 service .....................102 5.3.5.2...
Page 7 "FD 100/320Gbps NT and FX NT IHub System Basics, Management and OAM Guide" 6.8.1.2 shutdown ....................122 6.8.2 Event Control...................123 6.8.2.1 event-control....................123 6.8.3 Log Filter Commands ................124 6.8.3.1 filter......................124 6.8.3.2 default-action ...................125 6.8.4 Log Filter Entry Commands..............125 6.8.4.1 action .......................125 6.8.4.2 entry......................126 6.8.5 Log Filter Entry Match Commands ............127...
Page 8 "FD 100/320Gbps NT and FX NT IHub System Basics, Management and OAM Guide" 7.2.2.17 peer ......................145 7.2.2.18 session ....................146 7.2.2.19 sockets ....................146 7.2.2.20 timers.......................146 7.2.2.21 mpls ......................147 7.2.2.22 ftn......................147 7.2.2.23 ilm ......................148 7.2.2.24 lspinfo ......................148 7.2.2.25 memory-usage..................149 7.2.2.26 ospf......................149 7.2.2.27 ospf3......................149 7.2.2.28 abr ......................150...
Page 9 "FD 100/320Gbps NT and FX NT IHub System Basics, Management and OAM Guide" 7.2.3.17 mp-ecmp-rebalance.................163 7.2.3.18 security ....................163 7.2.3.19 service .....................164 7.2.3.20 id......................164 7.2.3.21 endpoint....................164 7.2.3.22 force-switchover ..................165 Ethernet Connection Fault Management ........167 Introduction....................167 8.1.1 Acronym Callout ..................168 ETH-CFM Building Blocks ...............169 8.2.1 Loopback ....................172 8.2.2...
Page 10 "FD 100/320Gbps NT and FX NT IHub System Basics, Management and OAM Guide" 8.12.2.5 single-ended-loss-test ................194 8.12.3 Show Commands ..................194 8.12.3.1 association....................194 8.12.3.2 cfm-stack-table ..................196 8.12.3.3 domain.....................197 8.12.3.4 mep......................198 8.12.3.5 mip......................203 8.12.3.6 Y1731 ......................203 Link Layer Discovery Protocol ..........213 Introduction....................213 LLDP CLI Command Reference..............213 9.2.1 LLDP Commands ..................213...
Page 11 "FD 100/320Gbps NT and FX NT IHub System Basics, Management and OAM Guide" List of figures Security..................41 Figure 1 Packet Formats ..................42 Events and Logs .................105 Figure 2 Event Logging Block Diagram ..............107 Ethernet Connection Fault Management ........167 Figure 3 MEP and MIP ..................171 Figure 4 MEP, MIP and MD levels.................172...
Page 12 "FD 100/320Gbps NT and FX NT IHub System Basics, Management and OAM Guide" 3HH-11982-AAAA-TQZZA Issue: 10...
Page 13 "FD 100/320Gbps NT and FX NT IHub System Basics, Management and OAM Guide" List of tables Introduction...................21 Table 1 Chapter names and descriptions...............21 Table 2 Command Syntax Symbols ...............22 System Management ..............23 Table 3 Priority during default-db activation ............25 Table 4 Priority during database corruption recovery..........26 Table 5 lacp-priority command ................29...
Page 14 "FD 100/320Gbps NT and FX NT IHub System Basics, Management and OAM Guide" Table 42 IP Protocol Names..................54 Table 43 dscp command ..................55 Table 44 dst-ip command ..................56 Table 45 dst-port command..................56 Table 46 fragment command..................57 Table 47 icmp-code command .................57 Table 48 icmp-type command ..................58 Table 49...
Page 15 "FD 100/320Gbps NT and FX NT IHub System Basics, Management and OAM Guide" Table 90 filter command ...................78 Table 91 ip command ....................79 Table 92 ipv6 command ...................80 Table 93 mac command ...................81 Table 94 lag command .....................83 Table 95 port command....................84 Table 96 router command ..................86...
Page 16 "FD 100/320Gbps NT and FX NT IHub System Basics, Management and OAM Guide" Table 136 lag command ...................140 Table 137 persistence command ................141 Table 138 submgt command ..................141 Table 139 summary command .................141 Table 140 router command ..................142 Table 141 jumbo-frame command................142 Table 142 protocol-counter command..............142...
Page 17 "FD 100/320Gbps NT and FX NT IHub System Basics, Management and OAM Guide" Table 185 domain command ..................158 Table 186 association command................158 Table 187 cvlan command ..................159 Table 188 log command ...................159 Table 189 test-event command ................159 Table 190 lsp-sync-exit command................160 Table 191 run-manual-spf command................160 Table 192...
Page 18 "FD 100/320Gbps NT and FX NT IHub System Basics, Management and OAM Guide" Table 233 Show eth-cfm mep command output fields ..........198 Table 234 ETH-CFM MEP Delay Measurement Test Field Descriptions....200 Table 235 ETH-CFM MEP Loss Measurement Test Field Descriptions ....201 Table 236 ETH-CFM MEP Synthetic Loss Measurement Test Field Descriptions.....................202...
Page 19: Preface
Readers must be familiar with general telecommunications principles. 1.4 Product naming When the term “ISAM” is used alone, then the 7302 ISAM, the 7330 ISAM FTTN and the 7360 ISAM FX are meant. If a feature is valid for only one of the products, the applicability will be explicitly stated.
Page 20: 1.7 Safety Information
Preface "FD 100/320Gbps NT and FX NT IHub System Basics, Management and OAM Guide" 1.7 Safety information For safety information, see the Safety Manual for your product. 1.8 Special information The following are examples of how special information is presented in this document. Danger indicates that the described activity or Danger —...
Page 21: Introduction
"FD 100/320Gbps NT and FX NT IHub System Introduction Basics, Management and OAM Guide" 2 Introduction 2.1 Contents 2.2 CLI Command Syntax Symbols 2.1 Contents Table lists the different chapters in this manual with a short description. Table 1 Chapter names and descriptions Chapter Description System Management...
Page 22: Table 2 Command Syntax Symbols
Introduction "FD 100/320Gbps NT and FX NT IHub System Basics, Management and OAM Guide" Table 2 Command Syntax Symbols Symbol Description A vertical line indicates that one of the parameters within the brackets or braces is required. Example: tcp-ack {true|false} Brackets indicate optional parameters.
Page 23: System Management
"FD 100/320Gbps NT and FX NT IHub System System Management Basics, Management and OAM Guide" 3 System Management 3.1 In this Chapter 3.2 Saving Configurations 3.3 Configuring System Management with CLI 3.4 System Management CLI Command Reference 3.5 System Management CLI Commands 3.1 In this Chapter This chapter provides information about configuring basic system management parameters.
Page 24 System Management "FD 100/320Gbps NT and FX NT IHub System Basics, Management and OAM Guide" The command saves the current configuration file into the special protected database. If the special protected database file already exists, it is overwritten. On a default-database activation, the configuration present in this special protected database will be restored.
Page 25: Table 3 Priority During Default-Db Activation
"FD 100/320Gbps NT and FX NT IHub System System Management Basics, Management and OAM Guide" Table 3 Priority during default-db activation default-db Special Protected OAM protected Configuration Restored activation Database database Without factory Present Present From OAM protected default database Without factory Not present Present...
Page 26: 3.3 Configuring System Management With Cli
System Management "FD 100/320Gbps NT and FX NT IHub System Basics, Management and OAM Guide" Table 4 Priority during database corruption recovery On a Shelf-restart Special protected OAM protected Configuration Restored Database database Configuration Database Present and Present and From OAM protected corruption no-corruption no-corruption...
Page 27: Save Command
"FD 100/320Gbps NT and FX NT IHub System System Management Basics, Management and OAM Guide" The place where the configuration files are saved is fixed (public directory on Core0 CF). The save command saves both the default configuration parameters and the non-default configuration parameters.
Page 28: System Information Commands
System Management "FD 100/320Gbps NT and FX NT IHub System Basics, Management and OAM Guide" 3.4.1 System Information Commands configure — system — lacp-priority lacp-priority — no lacp-priority — time — — polling-rate polling-rate — server ip-address [server-port udp port] —...
Page 29: 3.5 System Management Cli Commands
"FD 100/320Gbps NT and FX NT IHub System System Management Basics, Management and OAM Guide" 3.5 System Management CLI Commands The following commands are described below: • System Information Commands • System Administration Commands • Show Commands • Clear Commands 3.5.1 System Information Commands 3.5.1.1...
Page 30: Ntp
System Management "FD 100/320Gbps NT and FX NT IHub System Basics, Management and OAM Guide" 3.5.1.3 Table 7 ntp command Item Description Syntax Context configure>system>time Description This command enables the context to configure NTP client parameters. The ISAM can retrieve its system time using the NTP protocol, with up to 5 NTP servers used.
Page 31: Shutdown
"FD 100/320Gbps NT and FX NT IHub System System Management Basics, Management and OAM Guide" 3.5.1.6 shutdown Table 10 shutdown command Item Description Syntax [no] shutdown Context configure>system>time>ntp Description The shutdown command administratively disables the entity. When disabled, an entity does not change, reset, or remove any configuration settings or statistics.
Page 32: System Administration Commands
System Management "FD 100/320Gbps NT and FX NT IHub System Basics, Management and OAM Guide" Item Description Context configure>system> Description This command specifies the default service level ether type to be used for all v-VPLS services if the per-service ether type is not configured. Parameters etype —...
Page 33: Save
"FD 100/320Gbps NT and FX NT IHub System System Management Basics, Management and OAM Guide" 3.5.2.3 save Table 15 save command Item Description Syntax save Context admin Description This command saves the running configuration to a configuration file. 3.5.2.4 software-mngt ihub database oam-save-protected Table 16 software-mngt ihub database oam-save-protected command Item...
Page 34: Core1-Memory-Pools
System Management "FD 100/320Gbps NT and FX NT IHub System Basics, Management and OAM Guide" Table 18 Show System CPU Output Fields Label Description CPU Utilization The total amount of CPU time. Name The process or protocol name CPU Time (µSec) The CPU time each process or protocol has used in the specified time.
Page 35: Ntp
"FD 100/320Gbps NT and FX NT IHub System System Management Basics, Management and OAM Guide" 3.5.3.3 Table 21 ntp command Item Description Syntax ntp [detail] Context show>system Description This command displays the current operational parameters for NTP Client in the system 3.5.3.4 servers Table 22...
Page 36: User-User-Hairpin
System Management "FD 100/320Gbps NT and FX NT IHub System Basics, Management and OAM Guide" 3.5.3.6 user-user-hairpin Table 24 user-user-hairpin command Item Description Syntax user-user-hairpin Context show>system Description This command displays the status of user-user-hairpin communication (enabled or disabled). 3.5.3.7 vlan-dot1q-etype Table 25 vlan-dot1q-etype command...
Page 37: Ipv6-Prefix-Mgmt
"FD 100/320Gbps NT and FX NT IHub System System Management Basics, Management and OAM Guide" 3.5.3.9 ipv6-prefix-mgmt Table 28 ipv6-prefix-mgmt command Item Description Syntax ipv6-prefix-mgmt Context show>system Description This command displays IPv6 prefix resource usage in the system. 3.5.3.10 dst-ip Table 29 dst-ip command Item...
Page 38: Clear Commands
System Management "FD 100/320Gbps NT and FX NT IHub System Basics, Management and OAM Guide" 3.5.4 Clear Commands 3.5.4.1 alarm Table 31 alarm command Item Description Syntax alarm isis-adjacency-reject router-id router-id adjacency-idx adjacency-idx alarm isis-adjacency-down router-id router-id adjacency-idx adjacency-idx alarm ospf-neighbor-down router-id router-id neighbor-idx neighbor-idx alarm l2fw-stp-root-guard {port port-id | lag lag-id} service-id service-id alarm ihub-out-of-mem slot nt-slot alarm gen-switch-out-of-res...
Page 39 "FD 100/320Gbps NT and FX NT IHub System System Management Basics, Management and OAM Guide" Item Description Parameters isis-adjacency-reject — Specifies the isis adjacency reject alarm to be cleared isis-adjacency-down — Specifies the isis adjacency down alarm to be cleared ospf-neighbor-down —...
Page 40 System Management "FD 100/320Gbps NT and FX NT IHub System Basics, Management and OAM Guide" 3HH-11982-AAAA-TQZZA Issue: 10...
Page 41: Security
"FD 100/320Gbps NT and FX NT IHub System Security Basics, Management and OAM Guide" 4 Security 4.1 Security Features 4.2 Configuring Security with CLI 4.3 Security CLI Command Reference 4.4 Security CLI Commands 4.1 Security Features 4.1.1 Encryption Data Encryption Standard (DES) and Triple DES (3DES) are supported for encryption.
Page 42: Packet Format
Security "FD 100/320Gbps NT and FX NT IHub System Basics, Management and OAM Guide" 4.1.2.1 Packet Format Figure 1 Packet Formats 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Kind | Length...
Page 43: Keychain
"FD 100/320Gbps NT and FX NT IHub System Security Basics, Management and OAM Guide" 4.1.2.2 Keychain A keychain is a set of up to 64 keys, where each key is {A[i], K[i], V[i], S[i], T[i], S'[i], T'[i]} as described in draft-bonica-tcp-auth-05.txt, Authentication for TCP-based Routing and Management Protocols.
Page 44: 4.2 Configuring Security With Cli
Security "FD 100/320Gbps NT and FX NT IHub System Basics, Management and OAM Guide" Field Definition T'[i] End time after which configure>system>security>keychain>direction>uni>receive key[i] cannot be used by >entry>endtime receiving TCPs (2 of 2) 4.2 Configuring Security with CLI This section provides information to configure security using the Command Line Interface (CLI).
Page 45: Configuring Ipv6 Cpu Filters
"FD 100/320Gbps NT and FX NT IHub System Security Basics, Management and OAM Guide" The following displays an IP CPU filter configuration example: A:ALA-49>configure>system>security>cpu>ip-filter# info ---------------------------------------------- entry 10 create action drop description "CPU-Filter 10.4.101.2 #101" exit entry 20 create no action description "CPU-Filter 10.4.101.2 #201"...
Page 46: Configuring Keychains
Security "FD 100/320Gbps NT and FX NT IHub System Basics, Management and OAM Guide" entry 10 create action drop description "CPU-Filter 2001::1/64 #101" exit entry 20 create no action description "CPU-Filter 2010::1/64 #201" exit no shutdown ---------------------------------------------- A:ALA-49>configure>sys>sec>cpm>ipv6-filter# The following displays an IP/IPV6 CPU filter port and mask calculation example: TCP port number-2 bytes UDP port number-2 bytes This section describes the use of L4 mask and gives some examples on L4 masks.
Page 47: 4.3 Security Cli Command Reference
"FD 100/320Gbps NT and FX NT IHub System Security Basics, Management and OAM Guide" algorithm aes-128-cmac-96 begin-time 2006/12/18 22:55:20 exit exit exit exit keychain "basasd" direction receive entry 1 key "Ee7xdKlYO2DOm7v3IJv/84LIu96R2fZh" hash2 algorithm aes-128-cmac-96 tolerance forever exit exit exit exit exit ---------------------------------------------- A:ALA-1>configure>system>security#...
Page 48: Keychain Commands
Security "FD 100/320Gbps NT and FX NT IHub System Basics, Management and OAM Guide" — [no] dst-ip {ip-address/mask | ip-address netmask} — [no] dst-port [tcp/udp port-number] [mask] — [no] fragment {true | false} — [no] icmp-code icmp-code — [no] icmp-type icmp-type —...
Page 49: Show Commands
"FD 100/320Gbps NT and FX NT IHub System Security Basics, Management and OAM Guide" — no receive — send option-number — no send 4.3.4 Show Commands show — system — security — cpu-filter ip-filter [entry entryId — cpu-filter ipv6-filter [entry entryId —...
Page 50: Shutdown
Security "FD 100/320Gbps NT and FX NT IHub System Basics, Management and OAM Guide" Item Description Default No description associated with the configuration context. Parameters string — The description character string. Allowed values are any string up to 80 characters long composed of printable, 7-bit ASCII characters.
Page 51: Cpu-Filter Commands
"FD 100/320Gbps NT and FX NT IHub System Security Basics, Management and OAM Guide" Item Description Description This command allows you to define how applications (SNMPtrap, TFTP, FTPclient, Radius, ping, traceroute, and others) that generate unsolicited message set the source IP address. When set to interface: the source-IP address will always be set to the interface address of the interface used to send the IP message.
Page 52: Ip-Filter
Security "FD 100/320Gbps NT and FX NT IHub System Basics, Management and OAM Guide" Item Description Context configure>system>security>cpu-filter Description This command configures default action (accept or drop) for CPU filters which are common for both IP and IPv6. This default action of IP/IPv6 is applicable for the relevant version of IP traffic when the admin status of the IP-filter/IPv6-filter is up and no matching is available with any Ipv4/Ipv6 entries.
Page 53: Action
"FD 100/320Gbps NT and FX NT IHub System Security Basics, Management and OAM Guide" Item Description Parameters entry-id — Specifies the CPU filter policy ID number. Values: 1 — 1536 ISAM limits the number of entries to 256. Rules for counting entries: •...
Page 54: Match
Security "FD 100/320Gbps NT and FX NT IHub System Basics, Management and OAM Guide" 4.4.2.6 match Table 41 match command Item Description Syntax [no] match [protocol protocol-id] Context configure>system>security>cpu-filter>ip-filter>entry Description This command enables the context to enter match criteria for the filter entry. When the match criteria have been satisfied the action associated with the match criteria is executed.
Page 55: Dscp
"FD 100/320Gbps NT and FX NT IHub System Security Basics, Management and OAM Guide" Protocol Protocol ID Description rsvp Reservation Protocol General Routing Encapsulation ipv6-icmp ICMP for IPv6 ipv6-notxt No Next Header for IPv6 ipv6-opts Destination Options for IPv6 iso-ip ISO Internet Protocol eigrP EIGRP...
Page 56: Dst-Ip
Security "FD 100/320Gbps NT and FX NT IHub System Basics, Management and OAM Guide" Item Description Parameters dscp-name — Configures a DCSP name that represents a DiffServ code point. The mapping between a DCSP name and a DiffServ code point is fixed. Values: be, cp1, cp2, cp3, cp4, cp5, cp6, cp7, cs1, cp9, af11, cp11, af12, cp13, af13, cp15, cs2, cp17, af21, cp19, af22, cp21, af23, cp23, cs3, cp25, af31, cp27, af32, cp29, af33, cp31, cs4, cp33, af41, cp35, af42,cp37, af43,...
Page 57: Fragment
"FD 100/320Gbps NT and FX NT IHub System Security Basics, Management and OAM Guide" Item Description Description This command configures a destination TCP or UDP port number for an CPU filter match criterion. The no form of the command removes the destination port match criterion. Default None Parameters...
Page 58: Icmp-Type
Security "FD 100/320Gbps NT and FX NT IHub System Basics, Management and OAM Guide" Item Description Default no icmp-code Parameters icmp-code — The ICMP code values that must be present to match. (2 of 2) 4.4.2.12 icmp-type Table 48 icmp-type command Item Description Syntax...
Page 59: Service
"FD 100/320Gbps NT and FX NT IHub System Security Basics, Management and OAM Guide" 4.4.2.14 service Table 50 service command Item Description Syntax [no] service service-id Context configure>system>security>cpu-filter>ip-filter>entry>match Description This command specifies a service-id to be used in the match criteria. Parameters service-id —...
Page 60: Tcp-Ack
Security "FD 100/320Gbps NT and FX NT IHub System Basics, Management and OAM Guide" Item Description Context configure>system>security>cpu-filter>ip-filter>entry>match Description This command configures a source TCP or UDP port number or port range for an CPU filter match criterion. The no form of the command removes the source port match criterion. Default None Parameters...
Page 61: Shutdown
"FD 100/320Gbps NT and FX NT IHub System Security Basics, Management and OAM Guide" Item Description Description This command configures matching on the SYN bit being set or reset in the control bits of the TCP header of an IP packet as an CPU filter match criterion. The SYN bit is normally set when the source of the packet wants to initiate a TCP session with the specified destination IP address.
Page 62: Entry
Security "FD 100/320Gbps NT and FX NT IHub System Basics, Management and OAM Guide" 4.4.2.21 entry Table 57 entry command Item Description Syntax [no] entry entry-id [create] Context configure>system>security>cpu-filter>ipv6-filter Description This command creates a configuration context for a CPU filter entry. CPU filter entries specify either a forward or a drop action for packets based on specified match criteria.
Page 63: Dscp
"FD 100/320Gbps NT and FX NT IHub System Security Basics, Management and OAM Guide" Item Description Context configure>system>security>cpu-filter>ipv6-filter>entry Description This command enables the context to enter match criteria for the filter entry. Without any match criterion, the CPU filter is not effective in the hardware. When the match criteria have been satisfied the action associated with the match criteria is executed.
Page 64: Dst-Ip
Security "FD 100/320Gbps NT and FX NT IHub System Basics, Management and OAM Guide" 4.4.2.25 dst-ip Table 61 dst-ip command Item Description Syntax [no] dst-ip {ipv6-address[/prefix-length] Context configure>system>security>cpu-filter>ipv6-filter>entry>match Description This command matches a destination IPv6 address. To match on the destination IP address, specify the address and prefix length. For example, 11::12/128.
Page 65: Icmp-Code
"FD 100/320Gbps NT and FX NT IHub System Security Basics, Management and OAM Guide" 4.4.2.27 icmp-code Table 63 icmp-code command Item Description Syntax [no] icmp-code icmp-code Context configure>system>security>cpu-filter>ipv6-filter>entry>match Description Configures matching on ICMP code field in the ICMP header of an IPv6 packet as a filter match criterion.
Page 66: Service
Security "FD 100/320Gbps NT and FX NT IHub System Basics, Management and OAM Guide" Item Description Default None Parameters router-name — Base (2 of 2) 4.4.2.30 service Table 66 service command Item Description Syntax [no] service service-id Context configure>system>security>cpu-filter>ipv6-filter>entry>match Description This command specifies a service-id to be used in the match criteria.
Page 67: Src-Port
"FD 100/320Gbps NT and FX NT IHub System Security Basics, Management and OAM Guide" 4.4.2.32 src-port Table 68 src-port command Item Description Syntax [no] src-port src-port-number [mask] Context configure>system>security>cpu-filter>ipv6-filter>entry>match Description This command configures a source TCP or UDP port number for an IPv6 filter match criterion. The no form of the command removes the source port match criterion.
Page 68: Shutdown
Security "FD 100/320Gbps NT and FX NT IHub System Basics, Management and OAM Guide" Item Description Context configure>system>security>cpu-filter>ipv6-filter>entry>match Description This command configures matching on the SYN bit being set or reset in the control bits of the TCP header of an IP packet as an CPU filter match criterion. The SYN bit is normally set when the source of the packet wants to initiate a TCP session with the specified destination IP address.
Page 69: Keychain Commands
"FD 100/320Gbps NT and FX NT IHub System Security Basics, Management and OAM Guide" Item Description Parameters old-entry-id — Enter the entry number of an existing entry. Values: 1 — 1536 new-entry-id — Enter the new entry-number to be assigned to the old entry. Values: 1 —...
Page 70: Uni
Security "FD 100/320Gbps NT and FX NT IHub System Basics, Management and OAM Guide" 4.4.3.3 Table 75 bi command Item Description Syntax Context configure>system>security>keychain>direction Description This command configures keys for both send and receive stream directions. Default None 4.4.3.4 Table 76 uni command Item Description...
Page 71: Send
"FD 100/320Gbps NT and FX NT IHub System Security Basics, Management and OAM Guide" 4.4.3.6 send Table 78 send command Item Description Syntax send Context configure>system>security>keychain>direction>uni Description This command specifies the send nodal context to sign TCP segments that are being sent by the router to another device.
Page 72: Begin-Time
Security "FD 100/320Gbps NT and FX NT IHub System Basics, Management and OAM Guide" Item Description Parameters entry-id — Specifies an entry that represents a key configuration to be applied to a keychain. Values: 0 — 63 | null-key key — Specifies a key ID which is used along with keychain-name and direction to uniquely identify this particular key entry.
Page 73: End-Time
"FD 100/320Gbps NT and FX NT IHub System Security Basics, Management and OAM Guide" Item Description Parameters date hours-minutes — Specifies the date and time for the key to become active. Values: date: YYYY/MM/DD hours-minutes: hh:mm[:ss] UTC — Indicates that time is given with reference to Coordinated Universal Time in the input. now —...
Page 74: Tcp-Option-Number
Security "FD 100/320Gbps NT and FX NT IHub System Basics, Management and OAM Guide" Item Description Context configure>system>security>keychain>direction>bi>entry configure>system>security>keychain>direction>uni>receive>entry Description This command configures the amount of time that an eligible receive key should overlap with the active send key or to never expire. Parameters seconds —...
Page 75: Send
"FD 100/320Gbps NT and FX NT IHub System Security Basics, Management and OAM Guide" 4.4.3.13 send Table 85 send command Item Description Syntax send option-number no send Context configure>system>security>keychain>tcp-option-number Description This command configures the TCP option number accepted in TCP packets sent. The no form of this command returns the number to the default value.
Page 76: Cpu-Filter Ipv6-Filter
Security "FD 100/320Gbps NT and FX NT IHub System Basics, Management and OAM Guide" 4.4.4.2 cpu-filter ipv6-filter Table 87 cpu-filter ipv6-filter command Item Description Syntax cpu-filter ipv6-filter [entry entry-id] Context show>system>security Description This command displays a single filter or a summary of all filters. In the case that entryId is not specified, the output consists of a list of all CPU filters.
Page 77: Monitor Commands
"FD 100/320Gbps NT and FX NT IHub System Monitor Commands Basics, Management and OAM Guide" 5 Monitor Commands 5.1 Monitor Commands 5.2 Monitor CLI Command Reference 5.3 Monitor CLI Commands 5.1 Monitor Commands Monitor commands display specified statistical information related to the monitor subject (such as filter, port, lag, router) at a configurable interval until a count is reached.
Page 78: Monitor Cli Command
Monitor Commands "FD 100/320Gbps NT and FX NT IHub System Basics, Management and OAM Guide" 5.2.1 Monitor CLI Command monitor — filter — ip-filter-id entry entry-id [interval seconds] [repeat repeat] [absolute | rate] — ipv6 ipv6-filter-id entry entry-id [interval seconds] [repeat repeat] [absolute | rate] —...
Page 79: Table 91 Ip Command
"FD 100/320Gbps NT and FX NT IHub System Monitor Commands Basics, Management and OAM Guide" Item Description Description This command enables the context to configure criteria to monitor IP and MAC filter statistics. (2 of 2) 5.3.1.2 Table 91 ip command Item Description Syntax...
Page 80: Ipv6
Monitor Commands "FD 100/320Gbps NT and FX NT IHub System Basics, Management and OAM Guide" ---------------------------------------------------------------------------- At time t = 5 sec (Mode: Absolute) ---------------------------------------------------------------------------- Ing. Matches: 0 Egr. Matches ---------------------------------------------------------------------------- At time t = 10 sec (Mode: Absolute) ---------------------------------------------------------------------------- Ing.
Page 81: Mac
"FD 100/320Gbps NT and FX NT IHub System Monitor Commands Basics, Management and OAM Guide" Item Description Description This command enables IPv6 filter monitoring. The statistical information for the specified IPv6 filter entry displays at the configured interval until the configured count is reached. The first screen displays the current statistics related to the specified IPv6 filter.
Page 82 Monitor Commands "FD 100/320Gbps NT and FX NT IHub System Basics, Management and OAM Guide" Item Description Parameters mac-filter-id — The MAC filter policy ID. Values: 1 — 65535 entry entry-id — Displays information on the specified filter entry ID for the specified filter ID only.
Page 83: Lag Commands
"FD 100/320Gbps NT and FX NT IHub System Monitor Commands Basics, Management and OAM Guide" ---------------------------------------------------------------------------- Ing. Matches: 0 Egr. Matches ---------------------------------------------------------------------------- At time t = 15 sec (Mode: Rate) ---------------------------------------------------------------------------- Ing. Matches: 0 Egr. Matches ============================================================================ A:ALA-1>monitor>filter# 5.3.2 LAG Commands 5.3.2.1 Table 94 lag command...
Page 84: Port Commands
Monitor Commands "FD 100/320Gbps NT and FX NT IHub System Basics, Management and OAM Guide" A:ALA-12# monitor lag 12 ============================================================================ Monitor statistics for LAG ID 12 ============================================================================ Port-id Input Input Output Output Input Output Bytes Packets Bytes Packets Errors Errors ---------------------------------------------------------------------------- At time t = 0 sec (Base Statistics) ----------------------------------------------------------------------------...
Page 85 "FD 100/320Gbps NT and FX NT IHub System Monitor Commands Basics, Management and OAM Guide" Item Description Parameters port port-id — Specify up to 5 port IDs. The port can be either a network port (nwport-id) or an LT port (ltport-id). The syntax is: •...
Page 86: Router Commands
Monitor Commands "FD 100/320Gbps NT and FX NT IHub System Basics, Management and OAM Guide" Packets Errors ============================================================================ A:ALA-12>monitor# A:ALA-12>monitor# nt-a:sfp:1 interval 5 repeat 3 rate ============================================================================ Monitor statistics for nt-a:sfp:1 ============================================================================ Input Output ---------------------------------------------------------------------------- At time t = 0 sec (Base Statistics) ---------------------------------------------------------------------------- Octets Packets...
Page 87: Neighbor
"FD 100/320Gbps NT and FX NT IHub System Monitor Commands Basics, Management and OAM Guide" Item Description Parameters router-id — Specify the router name or service ID. Values: router-name: Base service-id: 1 — 2147483647 Default: Base (2 of 2) 5.3.4.2 neighbor Table 97 neighbor command...
Page 88: Statistics
Monitor Commands "FD 100/320Gbps NT and FX NT IHub System Basics, Management and OAM Guide" At time t = 0 sec ---------------------------------------------------------------------------- Recd. Prefixes Sent Prefixes Recd. Paths Suppressed Paths : 0 Num of Flaps i/p Messages : 916 o/p Messages : 916 i/p Octets : 17510...
Page 89 "FD 100/320Gbps NT and FX NT IHub System Monitor Commands Basics, Management and OAM Guide" Item Description Description This command displays statistical IS-IS traffic information at the configured interval until the configured count is reached. The first screen displays the current statistics related to the specified router statistics. The subsequent statistical information listed for each interval is displayed as a delta to the previous display.
Page 90 Monitor Commands "FD 100/320Gbps NT and FX NT IHub System Basics, Management and OAM Guide" ---------------------------------------------------------------------------- CSNP PSNP Unknown ---------------------------------------------------------------------------- At time t = 10 sec (Mode: Absolute) ---------------------------------------------------------------------------- ISIS Instance SPF Runs Purge Initiated LSP Regens. : 11 CSPF Statistics Requests Request Drops Paths Found...
Page 91: Session
"FD 100/320Gbps NT and FX NT IHub System Monitor Commands Basics, Management and OAM Guide" At time t = 10 sec (Mode: Rate) ---------------------------------------------------------------------------- ISIS Instance SPF Runs Purge Initiated LSP Regens. CSPF Statistics Requests Request Drops Paths Found Paths Not Found: 0 ---------------------------------------------------------------------------- PDU Type Received...
Page 92 Monitor Commands "FD 100/320Gbps NT and FX NT IHub System Basics, Management and OAM Guide" Item Description Parameters ldp-id — Specify the IP address of the LDP session to display. Values: ip-address[:label-space] ip-address — a.b.c.d label-space — [0 — 65535] interval seconds —...
Page 93 "FD 100/320Gbps NT and FX NT IHub System Monitor Commands Basics, Management and OAM Guide" Address Withdraw ---------------------------------------------------------------------------- At time t = 10 sec (Mode: Absolute) ---------------------------------------------------------------------------- FECs Hello 5288 5290 Keepalive 8226 8226 Init Label Mapping Label Request Label Release Label Withdraw Label Abort Notification...
Page 94: Statistics
Monitor Commands "FD 100/320Gbps NT and FX NT IHub System Basics, Management and OAM Guide" Init Label Mapping Label Request Label Release Label Withdraw Label Abort Notification Address Address Withdraw ---------------------------------------------------------------------------- At time t = 10 sec (Mode: Rate) ---------------------------------------------------------------------------- FECs Hello Keepalive...
Page 95 "FD 100/320Gbps NT and FX NT IHub System Monitor Commands Basics, Management and OAM Guide" Item Description Description Monitor statistics for LDP instance at the configured interval until the configured count is reached. The first screen displays the current statistics related to the specified router statistics. The subsequent statistical information listed for each interval is displayed as a delta to the previous display.
Page 96: Interface
Monitor Commands "FD 100/320Gbps NT and FX NT IHub System Basics, Management and OAM Guide" At time t = 0 sec (Base Statistics) ---------------------------------------------------------------------------- Addr FECs Sent : 0 Addr FECs Recv : 0 Serv FECs Sent : 1 Serv FECs Recv : 2 ---------------------------------------------------------------------------- At time t = 5 sec (Mode: Rate) ----------------------------------------------------------------------------...
Page 97 "FD 100/320Gbps NT and FX NT IHub System Monitor Commands Basics, Management and OAM Guide" Item Description Parameters interface — Specify the interface's IP address (ip-address) or interface name (ip-int-name). Up to 5 interfaces can be specified. If the string contains special characters (#, $, spaces, etc.), the entire string must be enclosed within double quotes.
Page 98 Monitor Commands "FD 100/320Gbps NT and FX NT IHub System Basics, Management and OAM Guide" Bad Versions ---------------------------------------------------------------------------- At time t = 10 sec (Mode: Absolute) ---------------------------------------------------------------------------- Tot Rx Packets : 8380 Tot Tx Packets : 8529 Rx Hellos : 8226 Tx Hellos : 8369 Rx DBDs...
Page 99 "FD 100/320Gbps NT and FX NT IHub System Monitor Commands Basics, Management and OAM Guide" ---------------------------------------------------------------------------- Tot Rx Packets : 0 Tot Tx Packets : 0 Rx Hellos Tx Hellos Rx DBDs Tx DBDs Rx LSRs Tx LSRs Rx LSUs Tx LSUs Rx LS Acks Tx LS Acks...
Page 100: Neighbor
Monitor Commands "FD 100/320Gbps NT and FX NT IHub System Basics, Management and OAM Guide" 5.3.4.7 neighbor Table 102 neighbor command Item Description Syntax neighbor interface [interface...(up to 5 max)] [interval seconds] [repeat repeat] [absolute | rate] Context monitor>router>ospf Description This command displays statistical OSPF or OSPF3 neighbor information at the configured interval until the configured count is reached.
Page 101 "FD 100/320Gbps NT and FX NT IHub System Monitor Commands Basics, Management and OAM Guide" At time t = 10 sec (Mode: Absolute) ---------------------------------------------------------------------------- Bad Nbr States LSA Inst fails Bad Seq Nums Bad MTUs Bad Packets LSA not in LSDB Option Mismatches: 0 Nbr Duplicates ----------------------------------------------------------------------------...
Page 102: Neighbor
Monitor Commands "FD 100/320Gbps NT and FX NT IHub System Basics, Management and OAM Guide" 5.3.4.8 neighbor Table 103 neighbor command Item Description Syntax neighbor interface [interface...(up to 5 max)] [interval seconds] [repeat repeat] [absolute | rate] Context monitor>router>rip Description This command displays statistical RIP neighbor information at the configured interval until the configured count is reached.
Page 103: Sdp
"FD 100/320Gbps NT and FX NT IHub System Monitor Commands Basics, Management and OAM Guide" Item Description Description This command enables the context to configure criteria to monitor specific service SAP criteria. (2 of 2) 5.3.5.2 Table 105 id command Item Description Syntax...
Page 104 Monitor Commands "FD 100/320Gbps NT and FX NT IHub System Basics, Management and OAM Guide" Item Description Parameters sdp-id[:vc-id] — Specify the SDP identifier. sdp-id: 1 — 17407 vc-id: 1 — 4294967295 far-end ip-address — The system address of the far-end ISAM for the SDP in dotted decimal notation.
Page 105: Events And Logs
"FD 100/320Gbps NT and FX NT IHub System Events and Logs Basics, Management and OAM Guide" 6 Events and Logs 6.1 In this Chapter 6.2 Logging Overview 6.3 Log Destinations 6.4 Event Logs 6.5 Configuration Notes 6.6 Configuring Logging with CLI 6.7 Log CLI Command Reference 6.8 Log CLI Commands 6.1 In this Chapter...
Page 106: 6.3 Log Destinations
Events and Logs "FD 100/320Gbps NT and FX NT IHub System Basics, Management and OAM Guide" • A subject identifying the affected object. • A short text description. Event control assigns the severity for each application event and whether the event should be generated.
Page 107: Session
"FD 100/320Gbps NT and FX NT IHub System Events and Logs Basics, Management and OAM Guide" 6.3.1 Session A session destination is a temporary log destination which directs entries to the active telnet or SSH session for the duration of the session. When the session is terminated, for example, when the user logs out, the event log is removed.
Page 108: Event Sources
Events and Logs "FD 100/320Gbps NT and FX NT IHub System Basics, Management and OAM Guide" 6.4.1 Event Sources In Figure 2, the event sources are the main categories of events that feed the log manager. • Security — The security event source is all events that affect attempts to breach system security such as attempts to access MIB tables to which the user is not granted access or attempts to enter a branch of the CLI to which access has not been granted.
Page 109: Log Manager And Event Logs
"FD 100/320Gbps NT and FX NT IHub System Events and Logs Basics, Management and OAM Guide" 2011 tmnxOspf VirtIfTxRetransmit WA sup 0 2012 tmnxOspf AreaOriginateLsa WA sup 0 2013 tmnxOspf AreaMaxAgeLsa WA gen 0 2014 tmnxOspf LsdbOverflow WA gen 0 2015 tmnxOspf LsdbApproachingOverflow...
Page 110: Event Log Entries
Events and Logs "FD 100/320Gbps NT and FX NT IHub System Basics, Management and OAM Guide" Each entry contains a combination of matching criteria that define the application, event number, router, severity, and subject conditions. The entry’s action determines how the packets should be treated if they have met the match criteria. Entries are evaluated in order from the lowest to the highest entry ID.
Page 111: Default System Log
"FD 100/320Gbps NT and FX NT IHub System Events and Logs Basics, Management and OAM Guide" Table 109 Log Entry Field Descriptions Label Description nnnn The log entry sequence number. YYYY/MM/DD The UTC date stamp for the log entry. • YYYY —...
Page 112: 6.5 Configuration Notes
Events and Logs "FD 100/320Gbps NT and FX NT IHub System Basics, Management and OAM Guide" log-id 99 description "Default System Log" no filter from main to memory no shutdown exit log-id 100 description "Default Serious Errors Log" filter 1001 from main to memory no shutdown...
Page 113: Log Types
"FD 100/320Gbps NT and FX NT IHub System Events and Logs Basics, Management and OAM Guide" • Allows you to assign a severity to the log messages. • Allows you to select the source and target of logging information. 6.6.1.1 Log Types Logs can be configured in the following contexts: •...
Page 114: Configuring An Event Log
Events and Logs "FD 100/320Gbps NT and FX NT IHub System Basics, Management and OAM Guide" 6.6.3.1 Configuring an Event Log A event log file contains information used to direct events and debug information to their respective destinations. One or more event sources can be specified. Use the following CLI syntax to configure an event log: configure>log log-id log-id...
Page 115: Log Management Tasks
"FD 100/320Gbps NT and FX NT IHub System Events and Logs Basics, Management and OAM Guide" configure>log filter (event filter) filter-id default-action (event filter) {drop|forward} description description-string entry (event filter) entry-id action (event filter) {drop|forward} description description-string match (event filter) application {eq|neq} application-id number {eq|neq|lt|lte|gt|gte} event-id router {eq|neq} router-name [regexp]...
Page 116: Deleting A Log File
Events and Logs "FD 100/320Gbps NT and FX NT IHub System Basics, Management and OAM Guide" log-id log-id description description-string filter 1 filter-id from {[main] [security] [change] [debug-trace]} to session The following displays the current log configuration: ALA-12>configure>log>log-id# info ---------------------------------------------- log-id 2 description "This is a test log file."...
Page 117: Modifying A Log Filter
"FD 100/320Gbps NT and FX NT IHub System Events and Logs Basics, Management and OAM Guide" ---------------------------------------------- A:ALA-12>configure>log# Use the following CLI syntax to delete a log file: configure>log no log-id log-id shutdown The following displays an example to delete a log file: configure# log configure>log# log-id 2 configure>log>log-id# shutdown...
Page 118: Deleting A Log Filter
Events and Logs "FD 100/320Gbps NT and FX NT IHub System Basics, Management and OAM Guide" The following displays an example of the log filter modifications: configure# log configure>log# filter 1 configure>log>filter # description "This allows <n>." configure>log>filter # default-action forward configure>log>filter # entry 1 configure>log>filter >entry $ action drop configure>log>filter >entry # match...
Page 119: Modifying Event Control Parameters
"FD 100/320Gbps NT and FX NT IHub System Events and Logs Basics, Management and OAM Guide" ---------------------------------------- A:ALA-12>configure>log>filter# The following displays an example of the command usage to delete a log filter: configure>log# no filter 1 6.6.4.5 Modifying Event Control Parameters Use the following CLI syntax to modify event control parameters: configure>log event-control application-id [event-name|event-number]...
Page 120: 6.7 Log Cli Command Reference
Events and Logs "FD 100/320Gbps NT and FX NT IHub System Basics, Management and OAM Guide" no event-control application [event-name |event-number] The following displays an example of the command usage to return to the default values: configure# log configure>log# no event-control "bgp" 2001 configure>log# no event-control "bgp"...
Page 121: Show Commands
"FD 100/320Gbps NT and FX NT IHub System Events and Logs Basics, Management and OAM Guide" — no description — [no] entry entry-id — action {drop | forward} — no action — description description-string — no description — [no] match —...
Page 122: Generic Commands
Events and Logs "FD 100/320Gbps NT and FX NT IHub System Basics, Management and OAM Guide" 6.8.1 Generic Commands 6.8.1.1 description Table 110 description command Item Description Syntax description description-string no description Context configure>log>filter filter-id configure>log>filter filter-id>entry entry-id configure>log>log-id log-id Description This command creates a text description stored in the configuration file for a configuration context.
Page 123: Event Control
"FD 100/320Gbps NT and FX NT IHub System Events and Logs Basics, Management and OAM Guide" 6.8.2 Event Control 6.8.2.1 event-control Table 112 event-control command Item Description Syntax event-control application-id [event-name | event-number] generate [severity-level] event-control application-id [event-name | event-number] suppress no event-control application-id [event-name | event-number] Context configure>log...
Page 124: Log Filter Commands
Events and Logs "FD 100/320Gbps NT and FX NT IHub System Basics, Management and OAM Guide" Item Description Parameters application-id — The application whose events are affected by this event control filter. Default: None, this parameter must be explicitly specified. Values: A valid application name.
Page 125: Default-Action
"FD 100/320Gbps NT and FX NT IHub System Events and Logs Basics, Management and OAM Guide" Item Description Default No event filters are defined. Parameters filter-id — The filter ID uniquely identifies the filter. Values: 1 —1001 (2 of 2) 6.8.3.2 default-action Table 114...
Page 126: Entry
Events and Logs "FD 100/320Gbps NT and FX NT IHub System Basics, Management and OAM Guide" Item Description Description This command specifies a drop or forward action associated with the filter entry. Multiple action statements entered will overwrite previous actions. The no form of the command removes the specified action statement.
Page 127: Log Filter Entry Match Commands
"FD 100/320Gbps NT and FX NT IHub System Events and Logs Basics, Management and OAM Guide" 6.8.5 Log Filter Entry Match Commands 6.8.5.1 match Table 117 match command Item Description Syntax [no] match Context configure>log>filter filter-id>entry entry-id Description This command creates context to enter/edit match criteria for a filter entry. When the match criteria is satisfied, the action associated with the entry is executed.
Page 128: Number
Events and Logs "FD 100/320Gbps NT and FX NT IHub System Basics, Management and OAM Guide" Item Description Parameters eq | neq — The operator specifying the type of match. Valid operators are: • eq: equal to • neq: not equal to application-id —...
Page 129: Router
"FD 100/320Gbps NT and FX NT IHub System Events and Logs Basics, Management and OAM Guide" 6.8.5.4 router Table 120 router command Item Description Syntax router {eq | neq} router-name [regexp] no router Context configure>log>filter>entry>match Description This command specifies the log event matches for the router. Parameters eq —...
Page 130: Subject
Events and Logs "FD 100/320Gbps NT and FX NT IHub System Basics, Management and OAM Guide" 6.8.5.6 subject Table 122 subject command Item Description Syntax subject {eq | neq} subject [regexp] no subject Context configure>log>filter filter-id>entry entry-id>match Description This command adds an event subject as a match criterion. The subject is the entity for which the event is reported, such as a port.
Page 131: Log-Id
"FD 100/320Gbps NT and FX NT IHub System Events and Logs Basics, Management and OAM Guide" Item Description Description This command selects the source stream to be sent to a log destination. One or more source streams must be specified. The source of the data stream must be identified using the from command before you can configure the destination using the to command.
Page 132: Show Commands
Events and Logs "FD 100/320Gbps NT and FX NT IHub System Basics, Management and OAM Guide" Item Description Default No log destinations are defined. Parameters log-id — The log ID number, expressed as a decimal integer. Values: 1 — 100 (2 of 2) 6.8.6.3 Table 125...
Page 133: Filter-Id
"FD 100/320Gbps NT and FX NT IHub System Events and Logs Basics, Management and OAM Guide" Item Description Parameters application-id — Only displays event control for the specified application Default: All applications Values: A valid application name. Valid applications are: bgp, debug, dhcp, filter, igmp_snooping, ip, isis, lag, ldp, logger, mirror, mpls, ospf, port, rip, route_policy, security, snmp, stp, svcmgr, system, user, vrtr event-name —...
Page 134: Log-Id
Events and Logs "FD 100/320Gbps NT and FX NT IHub System Basics, Management and OAM Guide" Item Description Parameters filter-id — Displays detailed information on the specified event filter policy ID. (2 of 2) Table describes the command output fields. Table 129 Filter ID Output Fields Label...
Page 135: Clear Commands
"FD 100/320Gbps NT and FX NT IHub System Events and Logs Basics, Management and OAM Guide" Label Description Filter ID The value is the index to the entry which defines the filter to be applied to this log's source event stream to limit the events output to this log's destination. If the value is 0, then all events in the source log are forwarded to the destination.
Page 136 Events and Logs "FD 100/320Gbps NT and FX NT IHub System Basics, Management and OAM Guide" 3HH-11982-AAAA-TQZZA Issue: 10...
Page 137: Tools
"FD 100/320Gbps NT and FX NT IHub System Tools Basics, Management and OAM Guide" 7 Tools 7.1 Tools CLI Command Reference 7.2 Tools CLI Configuration Commands 7.1 Tools CLI Command Reference This section shows the following command hierarchies: • Tools Dump Commands •...
Page 138: Tools Perform Commands
Tools "FD 100/320Gbps NT and FX NT IHub System Basics, Management and OAM Guide" — asbr [detail] — bad-packet interface-name — leaked-routes [summary | detail] — memory-usage [detail] — request-list [neighbor ip-address] [detail] — request-list virtual-neighbor ip-address area-id area-id [detail] —...
Page 139: 7.2 Tools Cli Configuration Commands
"FD 100/320Gbps NT and FX NT IHub System Tools Basics, Management and OAM Guide" 7.2 Tools CLI Configuration Commands The following commands are described below: • Generic Commands • Dump Commands • Perform Commands 7.2.1 Generic Commands 7.2.1.1 tools Table 133 tools command Item Description...
Page 140: Eth-Ring
Tools "FD 100/320Gbps NT and FX NT IHub System Basics, Management and OAM Guide" Item Description Parameters router-id - Specify the router ID. Default: Base (2 of 2) 7.2.2.2 eth-ring Table 135 eth-ring command Item Description Syntax eth-ring <ring-index> [clear] Context tools>dump>eth-ring Description...
Page 141: Persistence
"FD 100/320Gbps NT and FX NT IHub System Tools Basics, Management and OAM Guide" 7.2.2.4 persistence Table 137 persistence command Item Description Syntax persistence Context tools>dump Description This command dumps persistence information. 7.2.2.5 submgt Table 138 submgt command Item Description Syntax submgt Context...
Page 142: Router
Tools "FD 100/320Gbps NT and FX NT IHub System Basics, Management and OAM Guide" 7.2.2.7 router Table 140 router command Item Description Syntax router [router-instance] Context tools>dump tools>perform Description This command enables tools for the router instance. Default none Parameters router router-instance - Specifies the router instance.
Page 143: Non-Protocol-Counter
"FD 100/320Gbps NT and FX NT IHub System Tools Basics, Management and OAM Guide" 7.2.2.10 non-protocol-counter Table 143 non-protocol-counter command Item Description Syntax non-protocol-counter] Context tools>dump>router>jumbo-frame Description This command displays jumbo frame non-protocol drop counters. For example, non-protocols like SLF, IP, DLF, etc. 7.2.2.11 Table 144 fib command...
Page 144: Fec
Tools "FD 100/320Gbps NT and FX NT IHub System Basics, Management and OAM Guide" 7.2.2.13 Table 146 fec command Item Description Syntax fec prefixip-prefix/mask fec vc-type {ethernet | vlan} vc-id vc-id Context tools>dump>router>ldp Description This command displays information for an LDP FEC. Parameters prefix ip-prefix/mask —...
Page 145: Interface
"FD 100/320Gbps NT and FX NT IHub System Tools Basics, Management and OAM Guide" 7.2.2.15 interface Table 148 interface command Item Description Syntax interface [ip-int-name | ip-address] Context tools>dump>router>ldp Description This command displays information for an LDP interface. Parameters ip-int-name — Specifies the interface name. ip-address —...
Page 146: Session
Tools "FD 100/320Gbps NT and FX NT IHub System Basics, Management and OAM Guide" 7.2.2.18 session Table 151 session command Item Description Syntax session [ip-addr[:label-space] [connection | peer | adjacency] Context tools>dump>router>ldp Description This command displays information for an LDP session. Parameters ip-address —...
Page 147: Mpls
"FD 100/320Gbps NT and FX NT IHub System Tools Basics, Management and OAM Guide" 7.2.2.21 mpls Table 154 mpls command Item Description Syntax mpls Context tools>dump>router Description This command enables the context to display MPLS information. 7.2.2.22 Table 155 ftn command Item Description Syntax...
Page 148: Ilm
Tools "FD 100/320Gbps NT and FX NT IHub System Basics, Management and OAM Guide" 7.2.2.23 Table 156 ilm command Item Description Syntax ilm [endpoint endpoint | sender sender | nexthop nexthop | lsp-id lsp-id| tunnel-id tunnel-id | label start-label end-label] Context tools>dump>router>mpls Description...
Page 149: Memory-Usage
"FD 100/320Gbps NT and FX NT IHub System Tools Basics, Management and OAM Guide" 7.2.2.25 memory-usage Table 158 memory-usage command Item Description Syntax memory-usage Context tools>dump>router>mpls Description This command displays memory usage information for MPLS. 7.2.2.26 ospf Table 159 ospf command Item Description Syntax...
Page 150: Abr
Tools "FD 100/320Gbps NT and FX NT IHub System Basics, Management and OAM Guide" 7.2.2.28 Table 161 abr command Item Description Syntax abr [detail] Context tools>dump>router>ospf tools>dump>router>ospf3 Description This command enables to dump Area Border Router (ABR) information for OSPF. 7.2.2.29 asbr Table 162...
Page 151: Leaked-Routes
"FD 100/320Gbps NT and FX NT IHub System Tools Basics, Management and OAM Guide" 7.2.2.31 leaked-routes Table 164 leaked-routes command Item Description Syntax leaked-routes [summary | detail] Context tools>dump>router>ospf tools>dump>router>ospf3 Description This command enables to dump information about external routes leaked in to OSPF. 7.2.2.32 memory-usage Table 165...
Page 152: Retransmission-List
Tools "FD 100/320Gbps NT and FX NT IHub System Basics, Management and OAM Guide" 7.2.2.34 retransmission-list Table 167 retransmission-list command Item Description Syntax retransmission-list [neighbor ip-address] [detail] retransmission-list virtual-neighbor ip-address area-id area-id [detail] Context tools>dump>router>ospf tools>dump>router>ospf3 Description This command enables to dump retransmission list for OSPF. 7.2.2.35 route-summary Table 168...
Page 153: Service
"FD 100/320Gbps NT and FX NT IHub System Tools Basics, Management and OAM Guide" 7.2.2.37 service Table 170 service command Item Description Syntax service Context tools>dump Description Use this command to configure tools to display service dump information. 7.2.2.38 base-stats Table 171 base-stats command Item...
Page 154: L2Pt-Diags
Tools "FD 100/320Gbps NT and FX NT IHub System Basics, Management and OAM Guide" 7.2.2.40 l2pt-diags Table 173 l2pt-diags command Item Description Syntax l2pt-diags l2pt-diags clear l2pt-diags detail Context tools>dump>service Description Use this command to display L2pt diagnostics. Default none Parameters clear - Clears statistics after reading.
Page 155: Grp-Fdb
"FD 100/320Gbps NT and FX NT IHub System Tools Basics, Management and OAM Guide" 7.2.2.43 grp-fdb Table 176 grp-fdb command Item Description Syntax grp-fdb group-id Context tools>dump>service Description Use this command to display to display the number of MAC entries on a port protection group. Default none Parameters...
Page 156: Pred-Cpm-Stats
Tools "FD 100/320Gbps NT and FX NT IHub System Basics, Management and OAM Guide" 7.2.2.46 pred-cpm-stats Table 179 pred-cpm-stats command Item Description Syntax pred-cpm-stats pred-cpm-stats clear pred-cpm-stats detail Context tools>dump>pred Description Use this command to display CPM statistics related to port protection. Default none Parameters...
Page 157: Perform Commands
"FD 100/320Gbps NT and FX NT IHub System Tools Basics, Management and OAM Guide" Item Description Description Use this command to display port protection group configuration. Default none (2 of 2) 7.2.3 Perform Commands 7.2.3.1 perform Table 182 perform command Item Description Syntax...
Page 158: Mep
Tools "FD 100/320Gbps NT and FX NT IHub System Basics, Management and OAM Guide" 7.2.3.3 Table 184 mep command Item Description Syntax mep <mep-id> Context tools>perform>cfm Description The MEP index. Parameters <mep-id> Values: 1 - 8191 7.2.3.4 domain Table 185 domain command Item Description...
Page 159: Cvlan
"FD 100/320Gbps NT and FX NT IHub System Tools Basics, Management and OAM Guide" 7.2.3.6 cvlan Table 187 cvlan command Item Description Syntax cvlan <vlan-id> Context tools>perform>cfm Description Provides the C-VLAN with which the downstream LBM is to be inner-tagged. Parameters <vlan-id>...
Page 160: Lsp-Sync-Exit
Tools "FD 100/320Gbps NT and FX NT IHub System Basics, Management and OAM Guide" 7.2.3.9 lsp-sync-exit Table 190 lsp-sync-exit command Item Description Syntax [no] ldp-sync-exit Context tools>perform>router>isis tools>perform>router>ospf Description This command restores the actual cost of an interface at any time. When this command is executed, IGP immediately advertises the actual value of the link cost for all interfaces which have the IGPLDP synchronization enabled if the currently advertised cost is different.
Page 161: Cspf
"FD 100/320Gbps NT and FX NT IHub System Tools Basics, Management and OAM Guide" 7.2.3.12 cspf Table 193 cspf command Item Description Syntax cspf to ip-addr [from ip-addr] [bandwidth bandwidth] [include-bitmap bitmap] [exclude-bitmap bitmap] [hop-limit limit] [exclude-address excl-addr [excl-addr ...(up to 8 max)]] [srlg-group grp-id...(up to 8 max)] Context tools>perform>router>mpls...
Page 162: Trap-Suppress
Tools "FD 100/320Gbps NT and FX NT IHub System Basics, Management and OAM Guide" Item Description Parameters lsp lsp-name — Specifies the name that identifies the LSP. The LSP name can be up to 32 characters long and must be unique. path path-name —...
Page 163: Run-Manual-Spf
"FD 100/320Gbps NT and FX NT IHub System Tools Basics, Management and OAM Guide" 7.2.3.16 run-manual-spf Table 197 run-manual-spf command Item Description Syntax run-manual-spf externals-only Context tools>perform>router>ospf Description This command runs the Shortest Path First (SPF) algorithm. Default None Parameters externals-only - Specify the route preference for OSPF external routes.
Page 164: Service
Tools "FD 100/320Gbps NT and FX NT IHub System Basics, Management and OAM Guide" 7.2.3.19 service Table 200 service command Item Description Syntax service Context tools>perform Description This command enables the context to configure tools for services. 7.2.3.20 Table 201 id command Item Description...
Page 165: Force-Switchover
"FD 100/320Gbps NT and FX NT IHub System Tools Basics, Management and OAM Guide" 7.2.3.22 force-switchover Table 203 force-switchover command Item Description Syntax force-switchover sdp-id:vc-id no force-switchover Context tools>perform>service>id>endpoint Description This command forces a switch of the active spoke SDP for the specified service. Parameters sdp-id:vc-id —...
Page 166 Tools "FD 100/320Gbps NT and FX NT IHub System Basics, Management and OAM Guide" 3HH-11982-AAAA-TQZZA Issue: 10...
Page 167: Ethernet Connection Fault Management
"FD 100/320Gbps NT and FX NT IHub System Ethernet Connection Fault Management Basics, Management and OAM Guide" 8 Ethernet Connection Fault Management 8.1 Introduction 8.2 ETH-CFM Building Blocks 8.3 Loopback 8.4 Linktrace 8.5 Continuity Check (CC) 8.6 Two-Way Delay Measurement (ETH-DMM Y.1731) 8.7 Synthetic Loss Measurement (ETH-SL) 8.8 Loss Measurement (ETH-LM) 8.9 Y1731 proactive performance monitoring...
Page 168: Acronym Callout
Ethernet Connection Fault Management "FD 100/320Gbps NT and FX NT IHub System Basics, Management and OAM Guide" CFM uses Ethernet frames and is distinguishable by ether-type 0x8902. In certain cases the different functions will use a reserved multicast address that could also be used to identify specific functions at the MAC layer.
Page 169: 8.2 Eth-Cfm Building Blocks
"FD 100/320Gbps NT and FX NT IHub System Ethernet Connection Fault Management Basics, Management and OAM Guide" Acronym Callout Remote Defect Indication Synthetic Loss Message Synthetic Loss Reply Ethernet Test (Y.1731) (2 of 2) 8.2 ETH-CFM Building Blocks The IEEE and the ITU-T use their own nomenclature when describing administrative contexts and functions.
Page 170 Ethernet Connection Fault Management "FD 100/320Gbps NT and FX NT IHub System Basics, Management and OAM Guide" • 4 (VPN ID) - Hex value as described in RFC 2685, Virtual Private Networks Identifier • 32 (icc-format) - Exactly 13 characters from the ITU-T recommendation T.50. When a VID is used as the short MA name, 802.1ag Note —...
Page 171: Table 205 Eth-Cfm Support Matrix
"FD 100/320Gbps NT and FX NT IHub System Ethernet Connection Fault Management Basics, Management and OAM Guide" There are two locations in the configuration where ETH-CFM is defined. The domains, associations (including linkage to the service id), MIP creation method, common ETH-CFM functions and remote MEPs are defined under the top level eth-cfm command.
Page 172: Loopback
Ethernet Connection Fault Management "FD 100/320Gbps NT and FX NT IHub System Basics, Management and OAM Guide" Figure 4 MEP, MIP and MD levels 8.2.1 Loopback CFM supports a loopback test to verify the availability of a MAC address destination. When a loopback test is performed, the MEP launches an LBM to another MEP or MIP along the MA to check whether there is a failure in between the two points, and the location of the failure.
Page 173: 8.3 Loopback
"FD 100/320Gbps NT and FX NT IHub System Ethernet Connection Fault Management Basics, Management and OAM Guide" 8.3 Loopback A loopback message is generated by an MEP to its peer MEP or a MIP (Figure 5). The functions are similar to an IP ping to verify Ethernet connectivity between the nodes.
Page 174: Continuity Check (Cc)
Ethernet Connection Fault Management "FD 100/320Gbps NT and FX NT IHub System Basics, Management and OAM Guide" A traced MAC address is carried in the payload of the linktrace message. Each MIP and MEP receiving the linktrace message checks whether it has learned the target MAC address.
Page 175: Cfm Failure Check
"FD 100/320Gbps NT and FX NT IHub System Ethernet Connection Fault Management Basics, Management and OAM Guide" Figure 7 CFM Failure Check MIP10 MEP3 MIP1 MIP2 MIP3 MIP4 MIP5 MIP6 MIP7 MIP8 MEP4 MEP1 MIP11 Bridge MEP2 Port MIP12 Figure 8 CFM CC Failure Scenario MIP10 MEP3...
Page 176: Two-Way Delay Measurement (Eth-Dmm Y.1731)
Ethernet Connection Fault Management "FD 100/320Gbps NT and FX NT IHub System Basics, Management and OAM Guide" • CCM will declare a fault, when: • The CCM stops hearing from one of the remote MEPs for 3.5 times CC interval •...
Page 177: Synthetic Loss Measurement (Eth-Sl)
"FD 100/320Gbps NT and FX NT IHub System Ethernet Connection Fault Management Basics, Management and OAM Guide" 8.7 Synthetic Loss Measurement (ETH-SL) This synthetic loss measurement approach is a single-ended feature that allows the operator to run on-demand and proactive tests to determine “in”, “out” loss and “unacknowledged”...
Page 178: Loss Measurement (Eth-Lm)
Ethernet Connection Fault Management "FD 100/320Gbps NT and FX NT IHub System Basics, Management and OAM Guide" There is no way for the responding node to understand when a test is completed. For this reason a configurable “inactivity-timer” determines the length of time a test is valid.
Page 179: 8.9 Y1731 Proactive Performance Monitoring
"FD 100/320Gbps NT and FX NT IHub System Ethernet Connection Fault Management Basics, Management and OAM Guide" Y.1731 loss measurement functionality is implemented in software so the accuracy will be less. Since loss measurement is implemented in software additional data frames get transmitted and/or received between the time of reading the counter values and adding the frame with ETH-LM information to the data stream, the counter values copied in ETH-LM information become inaccurate.
Page 180: Modify Y1731 Proactive Session
Ethernet Connection Fault Management "FD 100/320Gbps NT and FX NT IHub System Basics, Management and OAM Guide" • Period The operator can specify the transmit interval for the Y1731 PM PDUs. SLM and DM will support period range from 1 secs to 10 secs (Default 1). LM will support 60 secs and 300 secs (default 60secs).
Page 181: 8.10 Y1731 Pm Restrictions
"FD 100/320Gbps NT and FX NT IHub System Ethernet Connection Fault Management Basics, Management and OAM Guide" 8.10 Y1731 PM Restrictions The following Y1731 PM restrictions exist: • Y1731 PM functionalities not supported on the following MEPs: • UP MEP •...
Page 182: Oam Commands
Ethernet Connection Fault Management "FD 100/320Gbps NT and FX NT IHub System Basics, Management and OAM Guide" — mhf-creation {default | none | explicit} — no mhf-creation — ccm-interval interval — no ccm-interval — [no] remote-mepid — slm — [no] inactivity-timer —...
Page 183: 8.12 Cli Commands
"FD 100/320Gbps NT and FX NT IHub System Ethernet Connection Fault Management Basics, Management and OAM Guide" 8.12 CLI Commands 8.12.1 CFM CLI Commands 8.12.1.1 domain Table 206 domain command Item Description Syntax domain md-index [format {mac | none | string}] [name md-name] level level domain md-index no domain md-index Context...
Page 184: Association
Ethernet Connection Fault Management "FD 100/320Gbps NT and FX NT IHub System Basics, Management and OAM Guide" 8.12.1.2 association Table 207 association command Item Description Syntax association ma-index [format {icc-based | integer | string | vid | vpn-id}] name ma-name association ma-index no association ma-index Context...
Page 185: Mhf-Creation
"FD 100/320Gbps NT and FX NT IHub System Ethernet Connection Fault Management Basics, Management and OAM Guide" 8.12.1.4 mhf-creation MIP Half-Function (MHF): MHFs generate CFM PDUs only as a response to received CFM PDUs. Table 209 mhf-creation command Item Description Syntax mhf-creation {default | none | explicit} no mhf-creation...
Page 186: Remote-Mepid
Ethernet Connection Fault Management "FD 100/320Gbps NT and FX NT IHub System Basics, Management and OAM Guide" 8.12.1.6 remote-mepid Table 211 remote-mepid command Item Description Syntax [no] remote-mepid mep-id Context configure>eth-cfm>domain>association Description This command configures the remote maintenance association end point MEP identifier. Parameters imep-id —...
Page 187: Shutdown
"FD 100/320Gbps NT and FX NT IHub System Ethernet Connection Fault Management Basics, Management and OAM Guide" Item Description Parameters domain – Connectivity Fault Management domain association- Maintenance Association for the Domain mep - CFM Maintenance Endpoint session - creates a session for the given mep (2 of 2) 8.12.1.9 shutdown...
Page 188: Mac-Address
Ethernet Connection Fault Management "FD 100/320Gbps NT and FX NT IHub System Basics, Management and OAM Guide" 8.12.1.11 mac-address Table 216 mac-address command Item Description Syntax mac-address mac-address Context configure>eth-cfm>y1731pm>domain Description Specifies the target unicast MAC address for the y1731pm session. The no form of the command reverts the value to the default.
Page 189: Period
"FD 100/320Gbps NT and FX NT IHub System Ethernet Connection Fault Management Basics, Management and OAM Guide" Item Description Default Parameters priority — <0,1,2…7> (2 of 2) 8.12.1.14 period Table 219 period command Item Description Syntax period period Context configure>eth-cfm>y1731pm>domain Description The value of period specifies the time to wait between the transmission of one OAM request and the next.
Page 190: Oam Cli Commands
Ethernet Connection Fault Management "FD 100/320Gbps NT and FX NT IHub System Basics, Management and OAM Guide" Item Description Description The value of measurement-period specifies the time after which the synthetic loss calculation is made periodically. If the value of this object is set to 'X' seconds, loss measurement calculations are done after every 'X' seconds.
Page 191: Linktrace
"FD 100/320Gbps NT and FX NT IHub System Ethernet Connection Fault Management Basics, Management and OAM Guide" Item Description Parameters mac-address -Destination MAC address. Format:xx:xx:xx:xx:xx:xx or xx-xx-xx-xx-xx-xx mep-id - MEP ID Values: 1..8191 md-index - MD index. Values: 1..4294967295 ma-index - MA index. Values: 1..4294967295 send-count - Number of loop back message to send Values: 1..5...
Page 192: Two-Way-Delay-Test
Ethernet Connection Fault Management "FD 100/320Gbps NT and FX NT IHub System Basics, Management and OAM Guide" Item Description Parameters mac-address - Destination MAC address. Format:xx:xx:xx:xx:xx:xx or xx-xx-xx-xx-xx-xx mep-id - MEP ID Values: 1..8191 md-index - MD index. Values: 1..4294967295 ma-index - MA index.
Page 193: Two-Way-Slm-Test
"FD 100/320Gbps NT and FX NT IHub System Ethernet Connection Fault Management Basics, Management and OAM Guide" 8.12.2.4 two-way-slm-test Table 224 two-way-slm-test command Item Description Syntax two-way-slm-test mac-address mep mep-id domain md-index association ma-index [priority priority] [send-count send-count] [size data-size] [timeout timeout] [interval interval] Context oam>eth-cfm Description...
Page 194: Single-Ended-Loss-Test
Ethernet Connection Fault Management "FD 100/320Gbps NT and FX NT IHub System Basics, Management and OAM Guide" 8.12.2.5 single-ended-loss-test Table 225 single-ended-loss-test command Item Description Syntax single-ended-loss-test mac-address mep mep-id domain md-index association ma-index [priority priority] [interval {1s}] [send-count send-count] Context oam>eth-cfm Description...
Page 195: Table 227 Show Eth-Cfm Association Command Output Fields
"FD 100/320Gbps NT and FX NT IHub System Ethernet Connection Fault Management Basics, Management and OAM Guide" Item Description Parameters ma-index - Specifies the MA index. Values: 1...4294967295 detail - Displays detailed information for the eth-cfm association. (2 of 2) Table shows the command output fields.
Page 196: Cfm-Stack-Table
Ethernet Connection Fault Management "FD 100/320Gbps NT and FX NT IHub System Basics, Management and OAM Guide" 8.12.3.2 cfm-stack-table Table 228 cfm-stack-table command Item Description Syntax cfm-stack-table [{all-ports | all-sdps}] [level 0..7] [direction up | down] cfm-stack-table port port-id [vlan qtag] [level 0..7] [direction up | down] cfm-stack-table sdp sdp-id[:vc-id] [level 0..7] [direction up | down] Context show>eth-cfm...
Page 197: Domain
"FD 100/320Gbps NT and FX NT IHub System Ethernet Connection Fault Management Basics, Management and OAM Guide" nt-a:xfp:2:100 Down 2101 90:f0:01:01:00:01 ------ ============================================================================ ============================================================================ CFM SDP Stack Table ============================================================================ Lvl Dir Md-index Ma-index MepId Mac-address Defect ---------------------------------------------------------------------------- nt-a:xfp:3:20:21 Down 90:fo:01:01:00:01 ---- ============================================================================ 8.12.3.3...
Page 198: Mep
Ethernet Connection Fault Management "FD 100/320Gbps NT and FX NT IHub System Basics, Management and OAM Guide" ==================================================================== 8.12.3.4 Table 232 mep command Item Description Syntax mep mep-id domain md-index association ma-index [loopback] [linktrace] Context show>eth-cfm Description This command displays Maintenance Endpoint (MEP) information. Parameters domain md-index - Displays the index of the MD to which the MP is associated, or 0, if none.
Page 199 "FD 100/320Gbps NT and FX NT IHub System Ethernet Connection Fault Management Basics, Management and OAM Guide" Label Description VcId VC Id ControlMep Control mep status HighestDefect Highest defect present CcmLtmPriority Priority of CCM and LTM messages CcmSequenceErr Total number of out-of-sequence CCMs received from all remote MEPs R-mepId Remote Mep Id Rx CC...
Page 200 Ethernet Connection Fault Management "FD 100/320Gbps NT and FX NT IHub System Basics, Management and OAM Guide" Table 234 ETH-CFM MEP Delay Measurement Test Field Descriptions Label Description Peer Mac Addr Displays the MAC address of the peer (remote) entity. Delay (us) Displays the measured delay (in microseconds) for the DM test.
Page 201 "FD 100/320Gbps NT and FX NT IHub System Ethernet Connection Fault Management Basics, Management and OAM Guide" Table 235 ETH-CFM MEP Loss Measurement Test Field Descriptions Label Description Far-End Mac Addr Displays the MAC address of the far-end (remote) node. Duration(sec) Displays the duration that the current test has been running.
Page 202 Ethernet Connection Fault Management "FD 100/320Gbps NT and FX NT IHub System Basics, Management and OAM Guide" Accumulated Frames Near-End Far-End Total Tx Total Rx Total Loss Loss Ratio(%) 2.78 0.00 ================================================================== Table shows the synthetic loss measurement test output fields. Table 236 ETH-CFM MEP Synthetic Loss Measurement Test Field Descrip- tions...
Page 203: Mip
"FD 100/320Gbps NT and FX NT IHub System Ethernet Connection Fault Management Basics, Management and OAM Guide" 8.12.3.5 Table 237 mip command Item Description Syntax Context show>eth-cfm Description This command displays SAPs/bindings provisioned for allowing the default MIP creation. Table shows the command output fields.
Page 204 Ethernet Connection Fault Management "FD 100/320Gbps NT and FX NT IHub System Basics, Management and OAM Guide" Table 239 Y1731 proactive loss session – show field Descriptions Label Description Domain Displays the domain of the Y1731 proactive session. Association Displays the association of the Y1731 proactive session. Displays the Maintenance association End Point of the Y1731 proactive session.
Page 205 "FD 100/320Gbps NT and FX NT IHub System Ethernet Connection Fault Management Basics, Management and OAM Guide" Label Description Total Rx The value of Rx Near end is the accumulated number of frames received at the local service endpoint of this MEP(RxFCl), and within the loss test duration of 15 Minutes. Near end/Far end The value of Rx Far end is the accumulated number of frames received at the far-end service endpoint(RxFCf), and within the loss test duration of 15 Minutes.
Page 206 Ethernet Connection Fault Management "FD 100/320Gbps NT and FX NT IHub System Basics, Management and OAM Guide" Elapsed-time Measured-time Valid-Intervals PDU Sent PDU Recieved PDU Discarded UnAcknowledged Accumulated Frames Near-End Far-End Total Tx 167217762 Total Rx 167217721 Total Loss Frames Loss Ratio Minimum Average Maximum...
Page 207 "FD 100/320Gbps NT and FX NT IHub System Ethernet Connection Fault Management Basics, Management and OAM Guide" Total Rx 481737005 Total Loss Frames Loss Ratio Minimum Average Maximum Near-End(%) 0.00 0.00 0.00 Far-End(%) 0.00 0.00 0.00 ================================================================== show eth-cfm y1731pm prev-15min-stats domain 3 association 2 mep 1 session 1 interval 1 ================================================================== ETH-CFM Y.1731 Previous 15 Min Statistics...
Page 208 Ethernet Connection Fault Management "FD 100/320Gbps NT and FX NT IHub System Basics, Management and OAM Guide" Table shows the proactive delay session output fields. Table 240 Y1731 proactive delay session – show field Descriptions Label Description Domain Displays the domain of the Y1731 proactive session. Association Displays the association of the Y1731 proactive session.
Page 209 "FD 100/320Gbps NT and FX NT IHub System Ethernet Connection Fault Management Basics, Management and OAM Guide" Label Description Delay variance (us) The value of minimum delay variance indicates the minimum amount of time delay Round trip variation, measured in microseconds, from the two most recent time delay Min/Avg/Max measurements (i.e.
Page 210 Ethernet Connection Fault Management "FD 100/320Gbps NT and FX NT IHub System Basics, Management and OAM Guide" ================================================================== ------------------------------------------------------------------ Domain Association Session Test type two-way-delay Admin status Enabled Priority Period Peer Mac Addr 00:07:72:a8:54:ad Valid-Intervals Interval-status Valid Elapsed-time Measured-time PDU Sent PDU Recieved PDU Discarded Delay (us)
Page 211 "FD 100/320Gbps NT and FX NT IHub System Ethernet Connection Fault Management Basics, Management and OAM Guide" Round Trip 6141 Delay variance (us) Minimum Average Maximum Round Trip 5919 ================================================================== Issue: 10 3HH-11982-AAAA-TQZZA...
Page 212 Ethernet Connection Fault Management "FD 100/320Gbps NT and FX NT IHub System Basics, Management and OAM Guide" 3HH-11982-AAAA-TQZZA Issue: 10...
Page 213: Link Layer Discovery Protocol
"FD 100/320Gbps NT and FX NT IHub System Link Layer Discovery Protocol Basics, Management and OAM Guide" 9 Link Layer Discovery Protocol 9.1 Introduction 9.2 LLDP CLI Command Reference 9.3 LLDP CLI Commands 9.1 Introduction The IEEE 802.1ab Link Layer Discovery Protocol (LLDP) standard defines protocol and management elements that are suitable for advertising information to stations attached to the same IEEE 802 LAN (emulation) for the purpose of populating physical or logical topology and device discovery management information...
Page 214: 9.3 Lldp Cli Commands
Link Layer Discovery Protocol "FD 100/320Gbps NT and FX NT IHub System Basics, Management and OAM Guide" 9.3 LLDP CLI Commands 9.3.1 LLDP Commands 9.3.1.1 lldp Table 241 lldp command Item Description Syntax lldp Context configure>system Description This command enables the context to configure system-wide Link Layer Discovery Protocol (LLDP) parameters.
Page 215: Message- Fast-Tx-Init
"FD 100/320Gbps NT and FX NT IHub System Link Layer Discovery Protocol Basics, Management and OAM Guide" 9.3.1.3 message- fast-tx-init Table 243 message-fast-tx-init command Item Description Syntax message-fast-tx-init count no message-fast-tx-init Context configure>system>lldp Description This command configures the number of LLDPDUs to send during the fast transmission period. The no form of the command returns the number to the default number.
Page 216: Tx-Credit-Max
Link Layer Discovery Protocol "FD 100/320Gbps NT and FX NT IHub System Basics, Management and OAM Guide" Item Description Description This command enables/disables LLDP on a system wide level. Default no shutdown (2 of 2) 9.3.1.6 tx-credit-max Table 246 tx-credit-max command Item Description Syntax...
Page 217: Tx-Interval
"FD 100/320Gbps NT and FX NT IHub System Link Layer Discovery Protocol Basics, Management and OAM Guide" 9.3.1.8 tx-interval Table 248 tx-interval command Item Description Syntax tx-interval interval no tx-interval Context configure>system>lldp Description This command configures the LLDP transmit interval time. The no form of the command returns the value to the default value.
Page 218: Figure
Link Layer Discovery Protocol "FD 100/320Gbps NT and FX NT IHub System Basics, Management and OAM Guide" Label Description Message Fast Tx Shows the message-fast-tx configured to set the duration of the fast transmission period for LLDP PDUs. Message Fast Tx Init Shows the message-fast-tx configured to set duration of the fast transmission period for LLDP PDUs.
Page 219 "FD 100/320Gbps NT and FX NT IHub System Link Layer Discovery Protocol Basics, Management and OAM Guide" Label Description Rem Table Inserts Shows the number of times, remote LLDP information of LLDP remote peers are inserted in the local MIB. Rem Table Deletes Shows the number of times, remote LLDP information of LLDP remote peers are removed in the local MIB.
Page 220 Link Layer Discovery Protocol "FD 100/320Gbps NT and FX NT IHub System Basics, Management and OAM Guide" 3HH-11982-AAAA-TQZZA Issue: 10...
Page 221 Customer document and product support Customer documentation Customer Documentation Welcome Page Technical Support Product Support Portal Documentation feedback Customer Documentation Feedback...

This manual is also suitable for:

7330 7360

Nokia 7302 Basics, Management And Oam Manual

Table of Contents

List of Tables

1 Preface

2 Introduction

3 System Management

4 Security

5 Monitor Commands

6 Events and Logs

7.2.2.6 Summary

Quick Links

Chapters

Related Manuals for Nokia 7302

Summary of Contents for Nokia 7302