NEC Sl2100 Networking Manual page 133

ISSUE 1.0
Program Program Name
Number
84-23-05 DT800/DT700 Multiline
Basic Information Set-
up – Invite Expire Timer
84-23-06 DT800/DT700 Multiline
Basic Information Set-
up – Signal Type of
Service
84-23-07 DT800/DT700 Multiline
Basic Information Set-
up – Error Display Tim-
er
84-23-08 DT800/DT700 Multiline
Basic Information Set-
up – Digest Authoriza-
tion Registration Expire
Timer
84-23-10 DT800/DT700 Multiline
Basic Information Set-
up – Number of Pass-
word Retries
84-23-11 DT800/DT700 Multiline
Basic Information Set-
up – Password Lock
Time
84-23-12 DT800/DT700 Multiline
Basic Information Set-
up – Reference Num-
ber
84-23-13 DT800/DT700 Multiline
Basic Information Set-
up – Media Type of
Service
84-23-14 DT800/DT700 Multiline
Basic Information Set-
up – Refer Expire Tim-
er
84-24-01 DT800/DT700 Multiline
CODEC Basic Informa-
tion Setup – Number of
G.711 Audio Frames
84-24-02 DT800/DT700 Multiline
CODEC Basic Informa-
tion Setup - G.711 Si-
lence Detection Mode
Networking Manual
Description/Comments
When INVITE message received from
SIP MLT does not contain Expires
header, the CPU uses this value for
timeout of outgoing call. E.g. The SIP
MLT hears RBT for duration of this
timer and then is disconnected.
Used for updating the IP terminals
SIGNALING TOS values.
The time that an IP terminal holds an
error message in the display. Setting 0
holds the error message indefinitely.
When Digest Authentication mode is
ON, this value is available.
After receiving Initial INVITE without
authentication information, CPU will
send 401 message to the SIP MLT,
then waits for an INVITE message
with the authentication message from
SIP MLT within this timer.
Additionally, after receiving Re-REG-
ISTER message for Keep Alive pur-
pose, the CPU sends a 401 message.
The number of times an incorrect
password can be entered when the
security key is pressed.
If set to (1), only one attempt is al-
lowed. When number of password re-
tries is met an error message displays
on the phone: Incorrect security code
password entered, press call key to
contact an administrator
Time to leave the terminal Locked Out
after entering the wrong security code.
Assign the network admin telephone
number. When the user presses the
Call key to contact the network admin-
istrator, this number is dialed.
Assign the IP terminals MEDIA TOS
values.
The valid period of the REFER sub-
scription.
Amount of audio in each RTP packet.
Select whether to compress silence
with G.711. When there is silence, the
RTP packet is not sent.
When VAD is enabled the CPU will
stop sending packets but the IP
Phone will continue to transmit silence
packets.
Assigned Data
Range: 0~65535 Sec.
Default is 180
Range: 0x00 ~ 0xFF
Default is 00
Range: 0 ~ 65535 Sec.
Default is 0
Range: 0 ~ 4294967295
Default is 0
Range: 0 ~ 255
Default is 0
Range; 0 ~ 120
Default: 0
Default is 0
Up to 32 Digits
(0~9, *, #, P, R, @)
Default is No Setting
Range: 0x00 ~ 0xFF
(0~9, A~F)
Default is 00
Range: 0 ~ 65535 Sec.
Default is 60
Range: 1~4
1 = 10ms
2 = 20ms
3 = 30ms
4 = 40ms
Default is 2
0 = Disable
1 = Enable
Default = 0
SL2100
1 2 3
X
X
X
X
X
X
X
X
X
X
X
9-35