Download
Share
Print this page
Toro Ultra Sonic Boom 130-8227 Installation Instructions Manual
  1. Manuals
  2. Brands
  3. Toro Manuals
  4. Paint Sprayer
  5. Ultra Sonic Boom 130-8227
  6. Installation instructions manual
Toro Ultra Sonic Boom 130-8227 Installation Instructions Manual

Toro Ultra Sonic Boom 130-8227 Installation Instructions Manual

Finishing kit for toro after multi pro 1750 turf sprayer
Hide thumbs
1
2
3
4
5
6
7
8

Advertisement

Quick Links

Download this manual
Ultra Sonic Boom
2013 and After Multi Pro
Model No. 130-8227
Note:
The Ultra Sonic Boom Leveling Kit (Model No. 41219) is required to install this kit.
Note:
Determine the left and right sides of the machine from the normal operating position.
This product contains a chemical or chemicals known to the State of California
Use of this product may cause exposure to chemicals known to the State of California
to cause cancer, birth defects, or other reproductive harm.
Loose Parts
Use the chart below to verify that all parts have been shipped.
Procedure
1
2
3
4
5
© 2017—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
Proposition 65 Warning
to cause cancer, birth defects, or reproductive harm.
Description
No parts required
No parts required
Wire harness
Lift-manifold bracket
Electronic controller cover
No parts required
Register at www.Toro.com.
™
Finishing Kit
®
1750 Turf Sprayer
WARNING
CALIFORNIA
Qty.
–
–
1
1
1
–
Form No. 3396-895 Rev A
Installation Instructions
Use
Prepare the machine.
Disconnect the battery.
Route the wire harness.
Install the lift-manifold bracket and
cover.
Connect the battery.
Original Instructions (EN)
All Rights Reserved *3396-895* A
Printed in the USA

Advertisement

loading

Related Manuals for Toro Ultra Sonic Boom 130-8227

Summary of Contents for Toro Ultra Sonic Boom 130-8227

  • Page 1 Install the lift-manifold bracket and cover. Electronic controller cover – No parts required Connect the battery. © 2017—The Toro® Company Register at www.Toro.com. Original Instructions (EN) All Rights Reserved *3396-895* A 8111 Lyndale Avenue South Printed in the USA Bloomington, MN 55420...

  • Page 2: Preparing The Machine

    Preparing the Machine Disconnecting the Battery No Parts Required No Parts Required Procedure Procedure 1. Park the machine on a level surface. WARNING 2. Engage the parking brake. Incorrect battery cable routing could damage 3. Shut off the engine and remove the key. the sprayer and cables causing sparks.
  • Page 3 Routing the Wire Harness Parts needed for this procedure: Wire harness g024082 Figure 2 Preparing to Route the Wire 1. Nut 3. Terminal (positive-battery Harness cable) 2. Battery post 4. Bolt Use the following graphic as an outline of routing the wire harness to the machine (Figure g209688...
  • Page 4 Routing the Wire Harness to the Front of the Machine Route the wire harness from the rear of the machine to the console as shown in Figure g208589 Figure 4 1. Wire harness Installing the Switches 1. Route the 8-socket connectors through the console (Figure 2.
  • Page 5 Installing the Wire Harness to the Fuse Block 1. Route the wire harness under the seat (Figure g210250 Figure 8 1. Connector—ultra sonic 2. Connector—machine boom finishing kit g210299 Figure 6 Installing the Wire Harness to the 1. Wire harness 2.
  • Page 6 Installing the Wire Harness to the Battery 1. Route the harness to the left from the side console to the flasher module. 2. Route the harness leg with the ring terminal to the positive post of the battery (Figure 10). g036958 Figure 10 g208941...

  • Page 7: Connecting The Battery

    5. Install the electronic controller cover; refer to the Installation Instructions for the ultra sonic boom leveling kit. Connecting the Battery No Parts Required Procedure 1. Align the ring terminal for the machine wire harness, the ring terminal of the kit wire harness, and the terminal for the positive battery cable to the positive battery post (Figure...