Page 4
■ 製品の呼び方 本文中の製品名称を次のように略して表記します。 製品名称 本文中の表記 ® Microsoft Windows Server™ 2003, Standard Edition ® Windows Server 2003 Microsoft Windows Server™ 2003, Enterprise Edition ® Microsoft Windows Server™ 2003, Standard x64 Edition Windows Server 2003 Windows ® Microsoft Windows Server™ 2003, Enterprise x64 Edition ®...
LAN ドライバのインストール この章では、LAN ドライバのインストール方法について説明します。 モジュールのバージョンレベル 本製品は、次の LAN ドライバで動作します。 OS の種類 LAN ドライバのバージョン Windows Server 2003 『PG-185x/186x/187x/188x/189x/PG-LND101 LAN ドライ Windows 2000 Server バ V9.1』 『PG-185x/186x/187x/188x/189x/PG-LND101 LAN Driver & Windows Server 2003 x64 Intel(R) PROSet LAN ドライバ V9.2』以降 LAN ドライバは、次のいずれかから入手してインストールしてください。 ・サーバブレード添付の ServerStart CD-ROM 内の LAN ドライバ ・富士通パソコン情報サイト...
3.1.1 バージョンレベルの確認方法 バージョンレベルの確認方法は次のとおりです。 OS の種類 確認方法 ® Windows Server 2003 ・ Intel PROSet の「ネットワークドライバ」のドライバ情 報の e1000325.sys のバージョン ・ 「デバイスマネージャ」で表示される LAN アダプタの名 称を右クリック後、 「プロパティ」→「ドライバ」→「ド ライバの詳細」で表示される e1000325.sys のバージョン ® Windows Server 2003 x64 ・ Intel PROSet の「ネットワークドライバ」のドライバ情 報の e1G5132e.sys のバージョン ・ 「デバイスマネージャ」で表示される LAN アダプタの名 称を右クリック後、...
Page 20
[デバイスマネージャ]をクリックします。 デバイスマネージャの一覧で、認識されているネットワークアダプタが存在するか を確認します。 認識されているネットワークアダプタが存在する場合は、 「ネットワークアダプタ」 が表示されます。 ・ 認識されているネットワークアダプタが存在する場合 最初に「ネットワークアダプタ」配下の LAN デバイス名に対して「3.2.2 LAN ド ライバの更新」 (→ P.21)を行ったあと、 「その他のデバイス」配下の「イーサ ネットコントローラ」に対して「3.2.3 LAN ドライバのインストール」 (→ P.23) を行ってください。 OS インストール直後に認識されたネットワークアダプタのドライバの更新を行 う前に、 「その他のデバイス」に対して LAN ドライバをインストールした場合...
Page 21
ドライバのインストールが開始されたあと、次の画面が表示されます。 [完了]をクリックすると、 「ヘルプとサポートセンター」の画面が表示されま すが、 [×]を クリックして画面を閉じてください。インストール後、デバイ スマネージャの LAN デバイス名に「!」マークが表示されますが、 すべての LAN ドライバインストール後、再起動すると正常に表示されます。 認識されているネットワークアダプタが存在しない場合 「その他のデバイス」配下の「イーサネットコントローラ」に対して、 「3.2.3 LAN ドライバのインストール」 (→ P.23)を行ってください。 3.2.2 LAN ドライバの更新 [デバイスマネージャ]の[ネットワークアダプタ]配下のすべての LAN デバイス名に対 して、 次の手順に従って行います。 ■ Windows Server 2003 / Windows 2000 Server の場合 「ネットワークアダプタ」配下の LAN デバイス名をダブルクリックしま す。 LAN デバイス名は、次のように表示されます。...
Page 22
LAN デバイスのアイコンをダブルクリックします。 プロパティが表示されます。 [ドライバ]タブをクリックし、 [ドライバの更新]をクリックします。 「ハードウェアの更新ウィザード」画面が表示されます。 「ソフトウェアを自動的にインストールする」を選択し、 [次へ]をクリッ クします。 ドライバのインストールが開始されます。 [完了]をクリックします。 [閉じる]をクリックします。 ■ Windows Server 2003 x64 の場合 「ネットワークアダプタ」配下の LAN デバイス名をダブルクリックしま す。 LAN デバイス名は、次のように表示されます。 LAN カード LAN デバイス名 PG-LND101 Intel(R) PRO/1000 MB Dual Port Server Connection AFT などが作成済みの場合、次の仮想アダプタが存在しますが、選択しな いでください。 ・Intel(R) Advanced Network Service Virtual Adapter LAN ドライバの...
Page 23
「製造元のファイルのコピー元」を LAN ドライバの格納されている場所 に指定し、 [OK]をク リックします。 「Intel(R) PRO/1000 MB Dual Port Server Connection」が表示された ら、 [次へ]をクリックします。 ドライバのインストールが開始されます。 [完了]をクリックします。 [閉じる]をクリックします。 ドライバの更新を行ったすべての LAN アダプタに対して正しく更新されていることを、 「3.1 モジュールのバージョンレベル」 (→ P.18)を参照して、バージョンが正しいことを 確認してください。 LAN アダプタのプロパティで「受信記述子」の値を小さく設定しないでください。 3.2.3 LAN ドライバのインストール [デバイスマネージャ]の[その他のデバイス]配下のすべての「イーサネットコント ローラ」 に対して、次の手順に従って LAN ドライバのインストールを行ってください。 ■ Windows Server 2003 の場合 LAN ドライバの...
Page 24
■ Windows Server 2003 x64 の場合 LAN ドライバの CD またはフロッピーディスクをセットします。 ダウンロードした LAN ドライバの格納したフォルダを確認しておいてください。 「その他のデバイス」配下の「イーサネットコントローラ」をダブルク リックします。 「イーサネットコントローラのプロパティ」画面が表示されます。 [ドライバ]タブをクリックし、 [ドライバの更新]をクリックします。 「ハードウェアの更新ウィザードの開始」画面が表示されます。 「一覧または特定の場所からインストールする」を選択し、 [次へ]をク リックします。 「検索しないで、インストールするドライバを選択する」を選択し、 [次 へ] をクリックします。 [ディスク使用]をクリックします。 「製造元のファイルのコピー元」を LAN ドライバの格納されている場所 に指定し、 [OK]をク リックします。 「Intel(R) PRO/1000 MB Dual Port Server Connection」が表示された ら、...
Page 25
[次へ]をクリックします。 「デバイスに最適なドライバをインストールする(推奨) 」を選択し、 [次 へ]をクリックします。 ドライバファイルの特定画面が表示されます。 検索場所のオプションに「CD-ROM ドライブ」または「フロッピーディ スクドライブ」などを選択し、 [次へ]をクリックします。 検出されたドライバが表示されます。 [次へ]をクリックします。 ドライバのインストールが開始され、終了すると完了画面が表示されます。 [完了]をクリックします。 [閉じる]をクリックします。 LAN ドライバの CD またはフロッピーディスクを取り出し、サーバブ レードを再起動します。 ドライバのインストールを行ったすべての LAN アダプタに対して、正しく更新されてい ることを、 「3.1 モジュールのバージョンレベル」 (→ P.18)を参照して、バージョンが正 しいか確認して ください。 LAN デバイス名は、次のように表示されます。 LAN カード LAN デバイス名 PG-LND101 Intel(R) PRO/1000 MB Dual Port Server Connection LAN アダプタのプロパティで「受信記述子」の値を小さく設定しないでください。...
Windows Server 2003 / Windows 2000 Server システムでの注意事項 ® ・ ServerStart を利用してドライバを自動インストールした場合は、Intel PROSet も自動的 にインストールされます 。 ® ・ Intel PROSet が「コントロールパネル」に表示されていれば、インストール済みです。 ® 本製品は、次の Intel PROSet でサポートされます。 - Windows Server 2003 / Windows 2000 Server の場合 ® 「V9.1(V9.1.0.0) 」の Intel PROSet - Windows Server 2003 x64 の場合...
その他の注意事項 ・ LAN ドータカードの LAN ポートに対して、PXE ブート(ネットワークブート)はサ ポートされません。 オンボードの LAN コントローラに対して、PXE ブートを実行してください。 ・ LAN ドータカードの WakeOnLAN 機能はサポートされません。 ・ LAN ドータカードの MAC アドレスおよび IP アドレスは、マネジメントブレードでは 確認できません。 ® PROSet または OS 上のハードウェア管理プログラムにて確認してくださ 同情報は、Intel い。 付録 A ...
Page 43
Thank you for purchasing the PRIMERGY 1Gbit/s Ethernet I/O Module (hereinafter referred to as this product or the card). The card can be installed in the daughter card slot of the Fujitsu server blade to configure the Local Area Network (LAN) system. This manual explains the 1Gbit/s Ethernet I/O Modules and the LAN driver (for Windows).
Page 44
Remarks Warning Descriptions Various symbols are used throughout this manual. These are provided to emphasize important points for your safety and that of others. The symbols and their meanings are as follows. Be sure to fully understand these before reading this manual. Ignoring this symbol could be potentially lethal.
Page 45
Abbreviations The following expressions and abbreviations are used throughout this manual. Product names Expressions and abbreviations ® Microsoft Windows Server™ 2003, Standard Edition Windows Server ® 2003 Microsoft Windows Server™ 2003, Enterprise Edition ® Microsoft Windows Server™ 2003, Standard x64 Edition Windows Server ®...
1Gbit/s Ethernet I/O Module This chapter explains the features and specifications of this product. Overview This product is an expansion LAN card exclusive to BX620 S2 Server Blade. This product has a dual-port (2 ports) LAN controller, and provides LAN connection completely separate/ independent of the onboard LAN.
A server blade installed with a 1Gbit/s Ethernet I/O Module and a server blade installed with a 2Gbit/s FC I/O Module cannot be installed to the same chassis. When a Switch Blade or a GbE Pass-Thru Blade is installed to network blade slot 3 or 4 (NET3 or 4), a FC Pass-Thru Blade cannot be installed at the same time.
Installing a 1Gbit/s Ethernet I/O Module This chapter explains how to install a 1Gbit/s Ethernet I/O Module to the server blade. WARNING • When installing or removing the 1Gbit/s Ethernet I/O Module, make sure to remove the server blade from the chassis. Failure to do so may cause electric shock.
Installing to BX620 S2 Server Blade To connect a 1Gbit/s Ethernet I/O Module to the external LAN (device), it is necessary to install a Switch Blade or GbE Pass-Thru Blade to network blade slot 3 or 4 (NET3 or 4) of the chassis.
Page 52
Install the 1Gbit/s Ethernet I/O Module. Check that the 1Gbit/s Ethernet I/O Module is securely inserted to the slot. 1Gbit/s Ethernet I/O Module Daughter card slot Secure the 1Gbit/s Ethernet I/O Module with the screws. Fix the 1Gbit/s Ethernet I/O Module using the three screws supplied with the card. Screws Attach the top cover.
Obtain and install a LAN driver from any of the following: • The LAN driver in the ServerStart CD-ROM provided with the server blade • The LAN driver available on the Fujitsu PRIMERGY website (http:// primergy.fujitsu.com) When using a LAN driver with a newer version than that of the above, refer to the user's guide or help file supplied with the driver.
3.1.1 How to check version level How to confirm the version level is described below. OS types Confirmation method Windows Server 2003 • Intel(R) PROSet [Network Driver] driver information e1000325.sys version • Right-click the LAN adapter name displayed in [Device Man- ager], and [Properties] →...
Page 55
Click [Device Manager]. On the Device Manager list, check if a recognized network adapter is present. Recognized network adapters Unrecognized network adapters When a recognized network adapter is present, [Network adapters] appears. • When a recognized network adapter is present Perform "3.2.2 Updating LAN Drivers"...
Page 56
Perform "3.2.3 Installing the LAN Driver" ( pg.58) on [Ethernet controller] under [Other devices]. 3.2.2 Updating LAN Drivers Perform the following procedures on all LAN device names under [Network adapters] in [Device Manager]. Windows Server 2003/Windows 2000 Server Double-click a LAN device name under [Network adapters]. The LAN device names are displayed as follows.
Page 57
When AFT is already created, the virtual adapter below exists. Do not select it. • Intel(R) Advanced Network Service Virtual Adapter Insert the LAN driver CD or floppy disk. Confirm the folder that contains the downloaded LAN driver in advance. Double-click the LAN device icon.
Page 58
3.2.3 Installing the LAN Driver According to the procedures below, install the LAN driver for all the Ethernet controllers listed under Other Devices of Device Manager. Windows Server 2003 Insert a CD or floppy disk of the LAN driver. Confirm the folder that contains the downloaded LAN driver in advance. Double-click [Ethernet controller] under [Other devices].
Page 59
When [Intel(R) PRO/1000MB Dual Port Server Connection] appears, click [Next]. The driver will be installed. Click [Finish]. Click [Close] to exit the properties window. Properties window closes. Eject the ServerStart CD-ROM, and restart the server blade. 3 Installing the LAN Driver...
Page 60
Windows 2000 Server Insert a CD or floppy disk of the LAN driver. Confirm the folder that contains the downloaded LAN driver in advance. Double-click [Ethernet controller] under [Other devices]. The [Ethernet Controller Properties] window appears. Click the [General] tab and click [Reinstall Driver]. The [Device Driver Upgrade Wizard] window appears.
Page 61
3.2.4 Removing the Driver Perform the following procedures to remove the driver. Log on with administrator privileges. ® Remove Intel PROSet. "4.4 Uninstalling"(pg.64) Click [Start] → [Settings] → [Control Panel] → [Add or Remove Applications] or [Add or Remove Programs]. Select [Intel(R) PRO Network Connections Drivers] and click [Change/Remove].
Obtain and install Intel PROSet from and of the following: • Intel(R)PROSet in the ServerStart CD-ROM provided with the server blade • Intel(R)PROSet available on the Fujitsu PRIMERGY website (http:// primergy.fujitsu.com) • For Windows Server 2003/ Windows 2000 Server Intel(R)PROSet "PG-185x/186x/187x/188x/189x/PG-LND101 LAN driver V9.1"...
Log on with the administrator privileges. ® Execute "ProSet.EXE" in the CD containing Intel PROSet or downloaded from the Fujitsu PRIMERGY website. [Automatic execution - runs setup immediately] appears. Click [OK]. [InstallShield Wizard] appears. Follow the instruction on the window for installation.
Uninstalling ® Perform the following procedures to uninstall Intel PROSet. Log on with the administrator privileges. Click [Start] → [Settings] → [Control Panel]. ® If team and VLAN are included, remove both of them using Intel PROSet before uninstallation. "5.3 Removing a Team"(pg.69) "6.3 Removing VLAN"(pg.74) Click [Add or Remove Programs] or [Add/Remove Applications].
Teaming(AFT/ALB/SFT) This chapter explains Teaming (AFT/ALB/SFT). In a system configuration containing a Switch Blade in the BX600 Server Blade, the Adaptive Load Balancing (ALB) function is not available. Teaming(AFT/ALB/SFT) AFT/ALB Adapter Fault Tolerance (AFT) is a technology of redundant paths between the server and switch (hub) using multiple Ethernet controllers (LAN adapters).
Page 66
Switch Fault Tolerance (SFT) is a redundant function with a configuration in which each LAN card is connected to a different switch. Spanning tree function on the switch is enabled, so that the switch can be used in the redundant configuration. When an error occurs (*) between the LAN card and its connected switch, the path to use is switched.
Page 67
Teaming 1Gbit/s Ethernet I/O Module during use When teaming this product, the possible software and teaming combinations will vary depending on the OS being used. Adhere to the table below. 2nd Port 1Gbit/s Ethernet Expansion Onboard LAN 1st Port I/O Module card slot Windows Onboard LAN...
Creating a Team Perform the following procedures to create a team. Log on with the administrator privileges. Click [Start] → [Settings] → [Control Panel] → [Intel®PROSet ® Wired], and start Intel PROSet. Select a LAN adapter to build in the team, and right click. Click [Add to Team] →...
Removing a Team Perform the following procedures to remove a team. Log on with the administrator privileges. Click [Start] → [Settings] → [Control Panel] → [Intel®PROSet ® Wired], and start Intel PROSet. Select the team to delete. Click [Remove team]. A confirmation message appears.
Event Log When AFT, ALB, or SFT is used, the following event logs will be generated (source: i ANSMiniport). Type Message Information Primary adapter is initialized: (adapter name) Information Adapter is initialized: (adapter name) Information (team name): Team is initialized. Information Current primary adapter is switched from the following adapter: (adapter name)
Detecting an Error in 1Gbit/s Ethernet I/O Modules Composing a Team and Replacing a Defective Card Follow the steps below to replace a 1Gbit/s Ethernet I/O Module composing a team. Replace a 1Gbit/s Ethernet I/O Module in the server blade. Start the server blade.
• Do not use protocol other than IP on the VLAN. Installing the LLC and LNDFC protocols using the Fujitsu communication control service will cause them to be bound (connected) unconditionally with the VLAN. In a system where protocols other than IP are installed with a VLAN, release the bind between the protocols and the VLAN.
Creating VLAN Perform the following procedures to create a VLAN. Log on with administrator privileges. Set the port of the switch connected to the Ethernet controller to enable send/receive of VLAN tag frames. Click [Start] → [Settings] → [Control Panel] → [Intel®PROSet ®...
Removing VLAN Follow the steps below to delete a VLAN. Log on with administrator privileges. Click [Start] → [Settings] → [Control Panel] → [Intel®PROSet ® Wired], and start Intel PROSet. Select the VLAN to delete and click it. Click [Remove VLAN]. A confirmation message appears.
Appendix A Setting Local Address Perform the following procedures to set a local address. Log on with administrator privileges. Click [Start] → [Settings] → [Control Panel] → [Intel®PROSet ® Wired], and start Intel PROSet. Select a LAN adapter to set the local address and click the [Advanced] tab.
Other Notes • The PXE boot (network boot) function is not supported for the LAN port of the 1Gbit/s Ethernet I/ O Module. Execute PXE boot to the onboard LAN controller. • WakeOnLAN function of the 1Gbit/s Ethernet I/O Module is not supported. •...
Fax: +852-2827-4724 Address: 10/F., Lincoln House, 979 King's Road Taikoo Place, Island East, Hong Kong • Indonesia: PT. Fujitsu Systems Indonesia Offices Headquarters Tel: +62-21-570-9330 (Hunting) Fax: +62-21-573-5150 Address: Wisma Kyoei Prince 10th Floor Jl. Jend. Sudirman Kav 3-4 Jakarta, Indonesia 10220 •...
Page 78
Address: Unit 802-8th floor, Fortuna Tower Hanoi 6B Lang ha Street, Ba dinh District, Hanoi Socialist Republic of Vietnam • United States: Fujitsu Computer Systems Corporation Tel: +1-800-831-3183 Fax: +1-408-496-0575 Address: 1250 East Arques Avenue, Sunnyvale, CA USA 94088-3470 For the latest information, refer to the Fujitsu PRIMERGY website (http://primergy.fujitsu.com).
Page 79
● 落丁、乱丁本は、お取り替えいたします。 • The contents of this manual may be revised without prior notice. • Fujitsu assumes no liability for damages to third party copyrights or other rights arising from the use of any information in this manual. • No part of this manual may be reproduced in any form without the prior written permission of Fujitsu.