Sealey VS2030.V2 Quick Start Manual

thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY.
Refer to Wear a face
instruction shield
manual
1. SAFEtY
‰ WARNING! Ensure Health & Safety, local authority and general workshop practice regulations are adhered to when using this
equipment.
Read instructions thoroughly to ensure safe and effective use.
9
9 9
IMpORtANt! Read instructions in conjunction with vehicle or equipment manufacturer's workshop manual. 9
9
maintain the apparatus in good condition (use an authorised service agent). Before each use check condition of each component. If any
9
component is damaged, replace immediately. Use genuine parts only. Unauthorised parts may not function correctly and will invalidate
the warranty.
Use in a suitable work area. Keep area free from unrelated materials and ensure that there is adequate lighting.
9
WARNING! Always wear approved eye, face and hand protection when pressure leakage testing.
‰
Keep children and unauthorised persons away from the working area.
9
DO NOt operate the leakage tester when you are tired or under the influence of alcohol, drugs or intoxicating medication.
8
DO NOt clean the equipment with solvents or other harsh chemicals.
8
DO NOt use the leakage tester for any purpose other than that for which it is designed.
8
When not in use return parts to the case, and store it in a safe, dry, childproof location.
9
2. INtRODUctION
Designed to charge the turbo system with a low pressure of regulated workshop mains air supply; to indicate the presence of leaks within the
system. The kit includes a pressure gauge, a shut off ball valve, a pressure relief valve, a mains air male barbed quick coupler and four pairs of
system stepped adaptors for use on a wide range of hose sizes. The kit can also be used on cooling system hoses. All items supplied in a storage
case.
3. SpEcIFIcAtION
model no .............................................................. VS2030.V2
Adaptor size ............................................................ 35-90mm
Weight ......................................................................... 2.52kg
4. cONtENtS
fig.1
5. OpERAtION
5.1. Follow the manufacturer's instructions for the removal, if required, of the device or hose to be tested. Use cloth or gloves and arm
protection if the system is known to be hot.
5.2. Connect an air line with known air pressure to the regulator of the tester with the ball valve shut (operating lever at 90° to hose axis).
IMpORtANt! Regulate air pressure in tester to 25psi maximum. Refer to manufacturer's manual relating to the maximum air
pressure of the turbo or other system being tested. Over pressurisation may damage system components.
© Jack Sealey Limited
tURBO SYStEM LEAKAGE tEStER
mODEL NO:
Wear protective
gloves
Original Language Version
VS2030.V2
Item no. part no.
1 VS2030.01
2 VS2030.01A
3 VS2030.02
4 VS2030.02A
5 VS2030.03
6 VS2030.03A
7 VS2030.04
8 VS2030.04A
9 VS2030.05
Diameter Description
80/85/90mm Inlet adaptor c/w air coupling
80/85/90mm Adaptor blank end
65/70/75mm Inlet adaptor c/w air coupling
65/70/75mm Adaptor blank end
50/55/60mm Inlet adaptor c/w air coupling
50/55/60mm Adaptor blank end
35/40/55mm Inlet adaptor c/w air coupling
35/40/45mm Adaptor blank end
N/A Pressure gauge assembly
VS2030.V2 Issue:2 (H,F) 26/04/19