Sealey VS2030.V2 Instructions

Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and properly
maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS
& CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO
DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS
SAFE FOR FUTURE USE.
1. SAFETY
WARNING! Ensure Health & Safety, local authority and general workshop practice regulations are adhered to when using this

equipment.
Read instructions thoroughly to ensure safe and effective use. Important! Read instructions in conjunction with vehicle or

equipment manufacturer's workshop manual.
Maintain the apparatus in good condition (use an authorised service agent). Before each use check condition of each component. If any

component is damaged, replace immediately. Use genuine parts only. Unauthorised parts may not function correctly and will invalidate
the warranty.
Use in a suitable work area. Keep area free from unrelated materials and ensure that there is adequate lighting.

WARNING! Always wear approved eye, face and hand protection when pressure leakage testing.

Keep children and unauthorised persons away from the working area.

DO NOT operate the leakage tester when you are tired or under the influence of alcohol, drugs or intoxicating

medication.
DO NOT clean the equipment with solvents or other harsh chemicals.

DO NOT use the leakage tester for any purpose other than that for which it is designed.

When not in use return parts to the case, and store it in a safe, dry, childproof location.

2. INTRODUCTION
Designed to charge the turbo system with a low pressure of regulated workshop mains air supply; to indicate the presence of leaks within the
system. The kit includes a pressure gauge, a shut off ball valve, a pressure relief valve, a mains air male barbed quick coupler and four pairs of
system stepped adaptors for use on a wide range of hose sizes. The kit can also be used on cooling system hoses. All items supplied in a storage
case.
3. CONTENTS
fig.1
Item No:. . . . . . . . . . Part No:. . . . . . . . . . . . . . . . .Diameter:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Description
1. . . . . . . . . . . . . . . . VS2030.01. . . . . . . . . . . . . . . . . . . . 80/85/90mm. . . . . . . . . . . . . . . . . Inlet Adaptor c/w Air Coupling
2. . . . . . . . . . . . . . . . VS2030.01A. . . . . . . . . . . . . . . . . . . 80/85/90mm. . . . . . . . . . . . . . . . . . . . . . . . . .Adaptor Blank End
3. . . . . . . . . . . . . . . . VS2030.02. . . . . . . . . . . . . . . . . . . . 65/70/75mm. . . . . . . . . . . . . . . . . Inlet Adaptor c/w Air Coupling
4. . . . . . . . . . . . . . . . VS2030.02A. . . . . . . . . . . . . . . . . . . 65/70/75mm. . . . . . . . . . . . . . . . . . . . . . . . . .Adaptor Blank End
5. . . . . . . . . . . . . . . . VS2030.03. . . . . . . . . . . . . . . . . . . . 50/55/60mm. . . . . . . . . . . . . . . . . Inlet Adaptor c/w Air Coupling
6. . . . . . . . . . . . . . . . VS2030.03A. . . . . . . . . . . . . . . . . . . 50/55/60mm. . . . . . . . . . . . . . . . . . . . . . . . . .Adaptor Blank End
7. . . . . . . . . . . . . . . . VS2030.04. . . . . . . . . . . . . . . . . . . . 35/40/45mm. . . . . . . . . . . . . . . . . Inlet Adaptor c/w Air Coupling
8. . . . . . . . . . . . . . . . VS2030.04A. . . . . . . . . . . . . . . . . . . 35/40/45mm. . . . . . . . . . . . . . . . . . . . . . . . . .Adaptor Blank End
9. . . . . . . . . . . . . . . . VS2030.05. . . . . . . . . . . . . . . . . . . . N/A. . . . . . . . . . . . . . . . . . . . . . . . . . Pressure Gauge Assembly
© Jack Sealey Limited
INSTRUCTIONS FOR:
TURBO SYSTEM LEAKAGE TESTER
VS2030.V2
MODEL NO:
Original Language Version
fig.2
VS2030.V2 Issue: 1 - 09/10/14