Epson S1C31 Setup Manual
  1. Manuals
  2. Brands
  3. Epson Manuals
  4. Microcontrollers
  5. S1C31
  6. Setup manual
Epson S1C31 Setup Manual

Epson S1C31 Setup Manual

Cmos 32-bit single chip microcontroller
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
CMOS 32-BIT SINGLE CHIP MICROCONTROLLER
S1C31 Family
Software Development
Setup Guide Rev.4
Rev.4.0

Advertisement

Table of Contents
loading

Related Manuals for Epson S1C31

Summary of Contents for Epson S1C31

  • Page 1 CMOS 32-BIT SINGLE CHIP MICROCONTROLLER S1C31 Family Software Development Setup Guide Rev.4 Rev.4.0...
  • Page 2 2. This evaluation board/kit or development tool is intended for use by an electronics engineer and is not a consumer product. The user should use it properly and in a safe manner. Seiko Epson dose not assume any responsibility or liability of any kind of damage and/or fire coursed by the use of it. The user should cease to use it when any abnormal issue occurs even during proper and safe use.

  • Page 3: Table Of Contents

    Connection of Hardware ......................8 3.3.1 When Using the I-jet ......................8 3.3.2 When Using the J-Link ......................9 Installation of peripheral circuit sample software package ..........11 Revision History ......................12 Seiko Epson Corporation S1C31 Family Software Development Setup Guide (Rev.4.0)

  • Page 4: Overview

    * 1: S1C31 Family is a microcontroller equipped with ARM Cortex -M0+ processor and is a product of Seiko Epson Corporation. 1.1 Software development environment list Figure 1.1.1 shows the software development environment set (toolchain) of the S1C31 Family. When software S1C31xxx Peripheral development *1 Provided by us...

  • Page 5: Acquisition Of Software Development Environment

    Environment (Integrated Development Environment /IDE and Debug Probe) to development the software for the S1C31 Family. Table 2.1.1 shows the recommended development Environment for S1C31 Family. Please contact the tool vendors or the tool vendor’s distributors to obtain these tools.

  • Page 6: Documents For Referencing Detailed Information

    The URL of this web site is as follows: < http://www.keil.com/ > *3: Please download from the SEGGER web site. The URL of this web site is as follows: < https://www.segger.com/ > *4: Please download from the Seiko Epson microcontroller web site. Seiko Epson Corporation S1C31 Family Software Development...

  • Page 7: Setup Of Software Development Environment

    The procedure of license registration varies depending on the type of license you purchased. For more information on the procedure of license registration, refer to “Quick Reference”(listed in Table 2.2.1). Seiko Epson Corporation S1C31 Family Software Development Setup Guide (Rev.4.0)

  • Page 8: When Using The Mdk-Arm

    For more information on the procedure of license registration, refer to “Getting Started with MDK”(listed in Table 2.2.1). Seiko Epson Corporation S1C31 Family Software Development Setup Guide (Rev.4.0)

  • Page 9: Installing The S1C31Setuptool Package

    If the software development environment to be used is not installed, "Destination Folder" will be displayed in an empty state. Exit the installer * When IAR EWARM is selected in [3] Seiko Epson Corporation S1C31 Family Software Development Setup Guide (Rev.4.0)
  • Page 10 3. Setup of Software Development Environment * When KEIL MDK-AMR is selected in [3] Seiko Epson Corporation S1C31 Family Software Development Setup Guide (Rev.4.0)

  • Page 11: Connection Of Hardware

    3. Setup of Software Development Environment 3.3 Connection of Hardware This section describes how to connect the hardware of the software development. The debug probe recommended for the S1C31 Family is I-jet or J-Link. 3.3.1 When Using the I-jet (1) Connect I-jet to the PC with IAR EWARM installed using the USB micro cable included with I-jet. This enables the PC to automatically install the device driver.

  • Page 12: When Using The J-Link

    (SEGGER) (S5U1C31xxxTx) Figure 3.3.2.1 Hardware Connection using J-Link *1: Figure 3.3.2.1 shows an example when the evaluation board (S5U1C31xxxTx) works using 5V power supply supplied from a debug probe (J-Link). Seiko Epson Corporation S1C31 Family Software Development Setup Guide (Rev.4.0)
  • Page 13 For more information on the connection of the hardware with J-Link, refer to the “J-Link/J-Trace User Guide”, “S5U1C31xxxTx Manual” and “S5U1C31001L1100 (Bridge Board Ver.2) Manual” (listed in Table 2.2.1) as necessary. Seiko Epson Corporation S1C31 Family Software Development Setup Guide (Rev.4.0)

  • Page 14: Installation Of Peripheral Circuit Sample Software Package

    3.4 Installation of peripheral circuit sample software package All kind of sample software and demo software for the S1C31 are included in the S1C31xxx peripheral circuit sample software package. About the S1C31xxx peripheral circuit sample software package, refer to "S1C31 Family Peripheral Circuit Sample Software Manual".

  • Page 15: Revision History

    Modified section 4.1 completely for the change of the sample software installation method. Rev. 4.0 2021/01/15 Delete Deleted section 4 Modify Modified section 1 Added “installing of S1C31SetupTool package” to Section 3.2 Seiko Epson Corporation S1C31 Family Software Development Setup Guide (Rev.4.0)
  • Page 16 FAX: +86-10-3299-0560 Riesstrasse 15, 80992 Munich, Germany Phone: +49-89-14005-0 FAX: +49-89-14005-110 Epson Taiwan Technology & Trading Ltd. 15F, No.100, Songren Rd, Sinyi Dist, Taipei City 110. Taiwan Phone: +886-2-8786-6688 Epson Singapore Pte., Ltd. 438B Alexandra Road, Block B Alexandra TechnoPark, #04-01/04, Singapore 119968...

Table of Contents