Related Manuals for Asus AAEON UP-AUDIO
Summary of Contents for Asus AAEON UP-AUDIO
- Page 1 UP-AUDIO Audio HAT for UP Board User’s Manual 1 Last Updated: November 18, 2019...
- Page 2 Copyright Notice This document is copyrighted, 2019. All rights are reserved. The original manufacturer reserves the right to make improvements to the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any means without the prior written permission of the original manufacturer.
- Page 3 Acknowledgement All other products’ name or trademarks are properties of their respective owners. Microsoft Windows is a registered trademark of Microsoft Corp. ⚫ Intel, Atom are registered trademarks of Intel Corporation ⚫ Realtek is a registered trademark of Realtek Semiconductor Corp. ⚫...
- Page 4 Packing List Before setting up your product, please make sure the following items have been shipped: Item Quantity UP-AUDIO ⚫ If any of these items are missing or damaged, please contact your distributor or sales representative immediately. Preface...
- Page 5 About this Document This User’s Manual contains all the essential information, such as detailed descriptions and explanations on the product’s hardware and software features (if any), its specifications, dimensions, jumper/connector settings/definitions, and driver installation instructions (if any), to facilitate users in setting up their product. Users may refer to the product page on AAEON.com for the latest version of this document.
- Page 6 Safety Precautions Please read the following safety instructions carefully. It is advised that you keep this manual for future references All cautions and warnings on the device should be noted. Make sure the power source matches the power rating of the device. Position the power cord so that people cannot step on it.
- Page 7 If any of the following situations arises, please the contact our service personnel: Damaged power cord or plug Liquid intrusion to the device iii. Exposure to moisture Device is not working as expected or in a manner as described in this manual The device is dropped or damaged Any obvious signs of damage displayed on the device...
- Page 8 FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
- Page 9 This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation.
- Page 10 China RoHS Requirements (CN) 产品中有毒有害物质或元素名称及含量 AAEON Main Board/ Daughter Board/ Backplane 有毒有害物质或元素 部件名称 铅 汞 镉 六价铬 多溴联苯 多溴二苯醚 (Pb) (Hg) (Cd) (Cr(VI)) (PBB) (PBDE) 印刷电路板 ○ ○ ○ ○ ○ ○ 及其电子组件 外部信号 ○ ○ ○ ○ ○ ○ 连接器及线材...
- Page 11 China RoHS Requirement (EN) Poisonous or Hazardous Substances or Elements in Products AAEON Main Board/ Daughter Board/ Backplane Poisonous or Hazardous Substances or Elements Hexavalent Polybrominated Polybrominated Component Lead Mercury Cadmium Chromium Biphenyls Diphenyl Ethers (Pb) (Hg) (Cd) (Cr(VI)) (PBB) (PBDE) PCB &...
-
Page 12: Table Of Contents
Table of Contents Chapter 1 - Product Specifications..................1 Specifications ......................2 Chapter 2 – Hardware Information ..................3 Dimensions ....................... 4 Jumpers and Connectors ..................5 List of Switches and Connectors................6 2.3.1 MIC Jack (CN1) ....................7 2.3.2 Line Out Jack (CN2) .................. -
Page 13: Chapter 1 - Product Specifications
Chapter 1 Chapter 1 - Product Specifications... -
Page 14: Specifications
Specifications System Realtek ALC5672 x 1 External Ports Line out x 1 MIC x 1 Internal connector HAT 40 GPIO male (1 x I2C, 5 x I2S, 1 x PWM, 3V3, 5V, GND) x 1 Speaker x 2 D-MIC x 2 Buzzer x 1 Miscellaneous Form Factor... -
Page 15: Chapter 2 - Hardware Information
Chapter 2 Chapter 2 – Hardware Information... -
Page 16: Dimensions
Dimensions Chapter 2 – Hardware Information... -
Page 17: Jumpers And Connectors
Jumpers and Connectors Top side D_CN1 D_CN2 Bottom side HAT1 Chapter 2 – Hardware Information... -
Page 18: List Of Switches And Connectors
List of Switches and Connectors Please refer to the table below for all of the board’s jumpers that you can configure for your application Reference Function Connector Type MIC Jack 5P C1F2R1-560-R 90D Line Out Jack 5P C1F2R1-570-R 90D D_CN1 DMIC_L 4P 710-73-04TWE0 D_CN2... -
Page 19: Mic Jack (Cn1)
2.3.1 MIC Jack (CN1) Signal H_GND_AUDIO MIC_R H_GND_AUDIO H_HP_DET MIC_L 2.3.2 Line Out Jack (CN2) Signal H_GND_AUDIO H_HP_OUT_R H_GND_AUDIO H_HP_DET H_HP_OUT_L 2.3.3 DMIC_L Wafer (D_CN1) Signal Signal DMIC_PW DMIC_SDA DMIC_SCL H_GND H_GND H_GND Chapter 2 – Hardware Information... -
Page 20: Dmic_R Wafer (D_Cn2)
2.3.4 DMIC_R Wafer (D_CN2) Signal Signal DMIC_PW DMIC_SDA DMIC_SCL H_GND H_GND H_GND 2.3.5 Speaker L Wafer (CN6) Signal Signal H_SPO_LP H_SPO_LN 2.3.6 Speaker R Wafer (CN7) Signal Signal H_SPO_RP H_SPO_RN Chapter 2 – Hardware Information... -
Page 21: Hat 40-Pin Connector (Hat1)
2.3.7 HAT 40-Pin Connector (HAT1) Signal Signal +V3P3A +V5A H_HAT_I2C1_SDA +V5A H_HAT_I2C1_SCL H_GND H_GND H_HAT_I2S6_BCLK H_GND +V3P3A H_GND H_GND H_ALC5672_JD H_GND H_HAT_PWM0 H_GND H_HAT_I2S6_WS_SYNC H_HAT_I2S6_SDI H_GND H_HAT_I2S6_SDO Chapter 2 – Hardware Information... -
Page 22: Chapter 3 -Installation Guide
Chapter 3 Chapter 3 –Installation Guide... -
Page 23: Up-Audio Installation
UP-AUDIO Installation This section details the steps to install the UP-AUDIO Audio HAT onto your UP Board. Step 1: Make sure your UP Board, UP-AUDIO and all accessories needed are ready. Step 2: Remove any screws attached to the UP Board. Chapter 3 –... - Page 24 Step 3: Attach the standoffs to your UP Board. Then, attach the UP-AUDIO, making sure to connect the HAT1 connector to the GP bus. Finally, secure the UP-AUDIO to the standoffs using screws. Installation is complete! You can now power on your UP Board. Proceed to the next section for software installation.
-
Page 25: Software Installation
Software Installation *Please visit https://www.up-community.org and go to the Downloads section to find the relevant drivers. For software installation, please follow the steps according to your operating system: Linux, Ubuntu Please refer to file “UP-Audio Linux Ubuntu driver for UP-CHT01.zip” and follow “RT5672_Installation_Guide_V1.0.pdf”...