Related Manuals for Asus AAEON UP Squared i12 Edge
Summary of Contents for Asus AAEON UP Squared i12 Edge
- Page 1 UP Squared i12 Edge Maker Board System UPS-EDGE-ADLP01 User’s Manual 2 Last Updated: November 14, 2023...
- Page 2 Copyright Notice This document is copyrighted, 2023. All rights are reserved. The original manufacturer reserves the right to make improvements to the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any means without the prior written permission of the original manufacturer.
- Page 3 Acknowledgement All other products’ name or trademarks are properties of their respective owners. Microsoft®, Windows® and Windows® 10 IoT Enterprise are registered ⚫ trademarks of Microsoft Corp. Intel® and Celeron® are registered trademarks of Intel Corporation ⚫ Core™ is a trademark of Intel Corporation ⚫...
- Page 4 Packing List Before setting up your product, please make sure the following items have been shipped: Item Quantity UPS-EDGE-ADLP01 (UP Squared i12 Edge) ⚫ If any of these items are missing or damaged, please contact your distributor or sales representative immediately. Preface...
- Page 5 About this Document This User’s Manual contains all the essential information, such as detailed descriptions and explanations on the product’s hardware and software features (if any), its specifications, dimensions, jumper/connector settings/definitions, and driver installation instructions (if any), to facilitate users in setting up their product. Users may refer to the product page at AAEON.com for the latest version of this document.
- Page 6 Safety Precautions Please read the following safety instructions carefully. It is advised that you keep this manual for future references All cautions and warnings on the device should be noted. Make sure the power source matches the power rating of the device. Position the power cord so that people cannot step on it.
- Page 7 If any of the following situations arises, please the contact our service personnel: Damaged power cord or plug Liquid intrusion to the device iii. Exposure to moisture Device is not working as expected or in a manner as described in this manual The device is dropped or damaged Any obvious signs of damage displayed on the device...
- Page 8 FCC Statement This device complies with Part 15 FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received including interference that may cause undesired operation.
- Page 9 China RoHS Requirements (CN) 产品中有毒有害物质或元素名称及含量 AAEON System QO4-381 Rev.A0 部件名称 有毒有害物质或元素 铅 汞 镉 六价铬 多溴联苯 多溴二苯醚 (Pb) (Hg) (Cd) (Cr(VI)) (PBB) (PBDE) 印刷电路板 × ○ ○ ○ ○ ○ 及其电子组件 外部信号 × ○ ○ ○ ○ ○ 连接器及线材 ○ ○...
- Page 10 China RoHS Requirement (EN) Hazardous and Toxic Materials List AAEON System QO4-381 Rev.A0 Hazardous or Toxic Materials or Elements Component Name PCB and Components Wires & Connectors for Ext.Connections Chassis CPU & RAM HDD Drive LCD Module Optical Drive Touch Control Module Battery This form is prepared in compliance with the provisions of SJ/T 11364.
-
Page 11: Table Of Contents
Table of Contents Chapter 1 - Product Specifications..................1 Specifications ......................2 Chapter 2 – Hardware Information ..................5 Dimensions ....................... 6 Jumpers and Connectors ..................7 List of Jumpers and Connectors ................9 2.3.1 Power Button (SW1) ..................10 2.3.2 Audio (CN1) .................... -
Page 12: Chapter 1 - Product Specifications
Chapter 1 Chapter 1 - Product Specifications... -
Page 13: Specifications
Specifications System 12th Gen Intel® Core™ Processor SoC Intel® Core™ i7-1270PE Intel® Core™ i7-1260P Intel® Core™ i5-1250PE Intel® Core™ i5-1240P Intel® Core™ i3-1220PE Intel® Celeron® Processor 7305E 13th Gen Intel® Core™ Processor SoC Intel® Core™ i7-1370PE Intel® Core™ i7-1360P Intel® Core™ i5-1340PE Intel®... - Page 14 System OS Support Windows® 10 IoT Enterprise Ubuntu 22.04 LTS Yocto 4 USB 3.2 Gen 2 (Type-A) x 2 USB 3.2 Gen 2 (Type-C) x 1 Display Port HDMI 1.4b/DP 1.2 STACK Connector x 1 DP 1.4a x 1 (via USB Type-C) Ethernet 1GbE RJ45 x 2 (Dual Stacked) (Realtek 8111H CG) —...
- Page 15 Environmental Operating Temperature 32°F ~ 140°F (0°C ~ 60°C) / 0.5 airflow Storage Temperature 0% ~ 90% relative humidity, non-condensing Operating Humidity -4°F ~ 158°F (-20°C ~ 70°C) MTBF 522,716 Certification CE/FCC Class A, RoHS Compliant, REACH Chapter 1 – Product Specifications...
-
Page 16: Chapter 2 - Hardware Information
Chapter 2 – Hardware Information Chapter 2... -
Page 17: Dimensions
Dimensions Chapter 2 – Hardware Information... -
Page 18: Jumpers And Connectors
Jumpers and Connectors Chassis Front I/O Rear I/O Chapter 2 – Hardware Information... - Page 19 Board Note: Not all PCBA-level internal connector pins are accessible via edge system external ports. Chapter 2 – Hardware Information...
-
Page 20: List Of Jumpers And Connectors
List of Jumpers and Connectors Please refer to the table below for all of the board’s jumpers and connectors that you can configure for your application Label Function Power Button Audio Power Input USB 3.0 Port (Type-A) DP/HDMI CN11 CN12 USB Type-C Port CN14 SATA... -
Page 21: Power Button (Sw1)
2.3.1 Power Button (SW1) Signal Signal PWRBTN_N 2.3.2 Audio (CN1) Signal Signal LOUT_R LOUT_L AUD_GND MIC_L_CN Chapter 2 – Hardware Information... -
Page 22: Power Input (Cn5)
2.3.3 Power Input (CN5) Signal Signal VCC_12V 2.3.4 USB 3.0 Port (CN6) Signal Signal USB2_C_DN1 USB2_C_DP1 USB3_RXN_CON_P1 USB3_RXP_CON_P1 Chapter 2 – Hardware Information... -
Page 23: Dp/Hdmi (Cn8)
Signal Signal USB3_TXN_CON_P1 USB3_TXP_CON_P1 USB2_C_DN2 USB2_C_DP2 USB3_RXN_CON_P2 USB3_RXP_CON_P2 USB3_TXN_CON_P2 USB3_TXP_CON_P2 2.3.5 DP/HDMI (CN8) Signal Signal DDI0_TXP_DP_0 DDI0_TXN_DP_0 DDI0_TXP_DP_1 DDI0_TXN_DP_1 DDI0_TXP_DP_2 DDI0_TXN_DP_2 DDI0_CLK_DP_DP DDI0_CLK_DP_DN DP_AUX_P Chapter 2 – Hardware Information... -
Page 24: Lan (Cn11)
Signal Signal DP_AUX_N DDI0_TYPE_C_HPD +3.3V DDI1_TXP_HDMI_2 DDI1_TXN_HDMI_2 DDI1_TXP_HDMI_1 DDI1_TXN_HDMI_1 DDI1_TXP_HDMI_0 DDI1_TXN_HDMI_0 DDI1_CLK_HDMI_DP DDI1_CLK_HDMI_DN HDMI_CEC_D HDMI_SCL HDMI_SDA HDMI_HPD_R 2.3.6 LAN (CN11) Signal Signal LAN1_ACTLEDN LAN2_ACTLEDN LAN1_ACTLEDP LAN2_ACTLEDP LAN1_LINK1000# LAN2_LINK1000# Chapter 2 – Hardware Information... -
Page 25: Usb Type-C (Cn12)
Signal Signal LAN1_LINK100# LAN2_LINK100# LAN1_MDI0+ LAN2_MDI0+ LAN1_MDI0- LAN2_MDI0- LAN1_MDI1+ LAN2_MDI1+ LAN1_MDI1- LAN2_MDI1- LAN1_MDI2+ LAN2_MDI2+ LAN1_MDI2- LAN2_MDI2- LAN1_MDI3+ LAN2_MDI3+ LAN1_MDI3- LAN2_MDI3- LAN1_DAC LAN2_DAC R10A LAN1_GND R10B LAN2_GND 2.3.7 USB Type-C (CN12) Signal Signal TCP0_RT_TX0_C_DP TCP0_RT_TX1_C_DP TCP0_RT_TX0_C_DN TCP0_RT_TX1_C_DN +VTCPC0_CC1_CONN +VTCPC0_CC2_CONN Chapter 2 – Hardware Information... -
Page 26: Sata (Cn14)
Signal Signal USB2_P5_R_DP USB2_P5_R_DP USB2_P5_R_DN USB2_P5_R_DN TCP0_SBU1_CONN TCP0_SBU2_CONN TCP0_RT_TXRX1_C_DN TCP0_RT_TXRX0_C_DN TCP0_RT_TXRX1_C_DP TCP0_RT_TXRX0_C_DP 2.3.8 SATA (CN14) Signal Signal SATA_C_TXP0 SATA_C_TXN0 SATA_C_RXN0 SATA_C_RXP0 Chapter 2 – Hardware Information... -
Page 27: Chapter 3 - Software Installation
Chapter 3 Chapter 3 – Software Installation... -
Page 28: Linux Setup
Linux Setup The UP Squared i12 Edge supports Linux operating systems (see Chapter 1 for specifications). For instructions on how to install a Linux OS onto your UP Squared i12 Edge, you can find several guides and tutorials in the wiki section of the UP website at https://up-board.org for both installing supported distributions as well as porting your own Linux build. -
Page 29: Appendix A - Up Framework Sdk Installation
Appendix A Appendix A – UP Framework SDK Installation... -
Page 30: Introduction
Introduction This section provides instructions for the installation of the UP Framework SDK. Instructions are provided for Windows 10. You can download the latest version of the UP Framework SDK from the UP community: https://downloads.up-community.org/download/up-sdk-for-windows-10-and-windows -iot/ A.2 Installation for Windows 10 Step 1 Locate the downloaded file UpFrameworkSetup.msi and run the installer. - Page 31 Step 2 Select the installation folder. Default destination path is C:\Program Files(x86)\AAEON\ You may also choose to install the UP Framework SDK for all users or only the current user. Press “Next” to continue installation. Step 3 Press “Next” to confirm the installation. Appendix A –...
- Page 32 Step 4 Press “Close” to exit once setup is complete. Appendix A – UP Framework SDK Installation...