How To Use Electric Home Shower; How To Use - Panasonic DH-3MS1 Operating Instructions Manual

HOW TO USE ELECTRIC HOME SHOWER

1. HOW TO USE

1. Turn "On" the Main Water Valve.
2. Switch "On" the Miniature Circuit Breaker (MCB) and ON/OFF DP (double pole) Switch.
3. Push the ELB Reset Lever if it is down.
4. Turn Water Volume Knob to clockwise.
• Turning it clockwise increases the volume of water thus decrease the water temperature.
• Turning it anticlockwise decreases the volume of water thus increase the water temperature.
5. Press the Push On-Off Lever, water will start flowing from the Shower Head and the ELB light
will turn red.
• To stop the water flow, press the Push On-Off Lever again (the position of the Push On-Off
Lever remains the same).
• This button controls both water and electricity supply to the set.
• Adjust to the desired shower condition by operating the Water Volume Knob and the Power
Control Knob / Temperature Control Knob.
Then the operation can be made easily by pushing the Push On-Off Lever only.
Press Push On-Off Lever before and after each shower.
Press the Push On-Off Lever only.
CAUTION
Do not pull.
6. Temperature setting
DH-3MS1
(a) The shower temperature can be gradually controlled by setting the Power Control Knob to the
desired position.
(b) If you turn the Power Control Knob clockwise the shower temperature will go up, reaching the
highest temperature at "High". The temperature can be gradually controlled.
(c) If the Power Control Knob is at "Off" position, the water temperature will remain at inlet temperature.
(d) In case of continuous usage at high temperature setting, water temperature will increase and it may
cause the control device in the set to activate temporarily resulting water temperature to drop.
DH-3MT1
(a) The shower temperature can be gradually controlled by setting the Temperature Control Knob to the
desired position.
(b) If the Temperature Control Knob is turned clockwise to 'Recommended Temp', you can get comfortable
water temperature.
(c) If the Temperature Control Knob is at "Off" position, the water temperature will remain at inlet water
temperature.
(d) Control Lamp (orange) will light up when water temperature is stable at the desired position.
(e) Control Lamp will turn off when water flow is too much, and it is beyond the controllable range.
(f) Reduce the water flow by turning the Water Volume Knob anticlockwise until Control Lamp is "On".
(g) In case of continuous usage at high temperature setting, water temperature will increase and it may
cause the control device to activate temporarily resulting water temperature to drop.
7. Select the preferred shower with the Shower Select Button. Please press the button fully.
8. Shower head can be set to various position.
(a) Loosen Shower Hanger Knob and adjust higher or lower.
Tighten Shower Hanger Knob.
(b) Loosen Shower Hanger Knob and Shower Hanger can be adjusted to the left or right.
Tighten Shower Hanger Knob.
(c) The angle of Shower Head can be adjusted by moving the Shower Head upper or lower.
Shower Select
Button
Press
Shower Head
(a)
Shower Hanger
Knob
Shower
Hanger
- 15 -
ELB Test
ELB Reset
Push Up
ELB: ON condition
ELB Test
ELB Reset
Push Up
ELB: OFF condition
Off High
Make sure push
Temp Control
ELB Control at the center of
Push On-Off
Lever only.
ELB Test
Push On-Off
ELB Reset DH-3MT1
Push Up
DH-3MS1
Power Control Knob
Off
Power Control
ELB
ELB Test
Push On-Off
ELB Reset
Push Up
ELB Lamp
DH-3MT1
Temperature Control Knob
Off
Temp Control
ELB
ELB Test
Push On-Off
ELB Reset
Push Up
ELB Lamp
Control Lamp
(b) (c)
Off High
Temp Control
ELB Control
Off High
Push On-Off
DH-3MT1
Temp Control
ELB Control
Push On-Off
DH-3MT1
High
DH-3MS1
High
Control
DH-3MT1