Advertisement
Step1 Fix the mount bracket and hang the camera (continued)
◆ Here explains an example of installation on a wall
Mount bracket (example: WV-Q122A)
using wall mount bracket (WV-Q122A). For detailed
installation information and procedure, refer to
operating instructions of each mount bracket.
【3】Process the installation surface
150~160mm
Decide the attachment position and bore holes for
{5-29/32 inches~
screws or anchors on the wall and a hole for wiring
6-5/16 inches}
Camera
as occasion demands.
attachment port
【4】 Pass a cable into mount bracket and fix it
Fixing screws (4 pcs.) (M10: locally procured)
on the installation surface
① Insert the cables coming from installation surface from rear
surface of mount bracket to internal and pull them out from
camera attachment port (cable cover attachment side).
* When passing the cables into mount bracket, take
care not to apply unreasonable force to the cables.
② Apply waterproof treatment to the installation sur-
150~160mm
{5-29/32 inches~
face and the cap of the mount bracket backside.
6-5/16 inches}
③ Attach the mount bracket to wall surface using
fixing screws (4 pcs.) (M10: locally procured).
IMPORTANT:
• After waterproofing the hole for fixing mount bracket, the port for pulling out the cable on
installation surface, and the cap part on rear surface of mount bracket, fix the mount
bracket on the installation surface.
• Fixing screw: Minimum pull-out strength (per 1 pc.)
WV-Q121B
1411 N {317 lbf}
WV-Q122A
823 N {185 lbf}
• Adjust the length of cable from camera attachment port of mount bracket to cable end to
150~160mm {5-29/32 inches~6-5/16 inches}. (If the cable that is pulled out is too long,
storage after wiring becomes difficult. On the contrary, if it is too short, the cable cannot
reach to the camera when installing the camera. Adjust the cable length carefully.)
◆The following works are common to Q121B/Q122A (option) and mount bracket (locally procured).
【5】Process the Ethernet cable (locally procured) and attach
RJ45
the waterproof connector cover and cap (accessory)
waterproof
RJ45 plug
connector
First pass the Ethernet cable through the RJ45
(locally
cover
waterproof connector cap (accessory) and then
pocured)
(accessory)
through the RJ45 waterproof connector cover
(accessory). Next, use a specialized tool (locally
procured) to crimp the RJ45 plug (locally procured) to
the end of the Ethernet cable.
Ethernet cable (locally procured)
IMPORTANT:
• Take care not to remove the rubber parts from inside the RJ45 waterproof connector cover (accessory).
• The maximum length of the Ethernet cable (locally procured) is 100 m, and the external
dimensions of it are from ø5 mm {ø3/16 inches} to ø6.5 mm {ø1/4 inches}.
Step2 Making connections
【2】Power cable
Brown
To the power supply (24 V AC 50 Hz/60 Hz)
Blue
Black
GND
Ethernet cable
【1】RJ45 (female) Network cable
(category 5e or better, straight)
To a PoE+ hub
RJ45 waterproof connector (accessory)
【3】Alarm input/output cable
【3】8P alarm cable (accessory)
To a sensor
【4】Audio input cable (white)
To a plug-in power type microphone
【5】Audio output cable (black)
To an external powered speaker
*This illustration represents WV-X6531N.
【1】Connect an Ethernet cable (category 5e or better, straight) to RJ45 (female)
network cable.
RJ45
waterproof
① Insert the RJ45 plug (locally procured) into
RJ45
RJ45 plug
connector
the RJ45 waterproof jack connected to
waterproof
(locally
cover
the camera.
jack
pocured)
(accessory)
② Connect the RJ45 waterproof connector
cover (accessory) to the RJ45 waterproof
jack and then rotate the RJ45 waterproof
connector cover until the "⇦" marks align.
③ Connect the RJ45 waterproof connector cap
(accessory) to the RJ45 waterproof connector
cover and rotate the RJ45 waterproof
connector cap until there is no gap between it
and the RJ45 waterproof connector cover.
IMPORTANT:
• If the procedure for the RJ45 waterproof connector (accessory) part is not correctly fol-
lowed, the waterproofing may be compromised. Do not install the camera where the RJ45
waterproof connector is exposed to constant rain or moisture.
• When you remove the RJ45 waterproof connector, be sure to follow the reverse order of the con-
necting procedures. (The RJ45 waterproof jack may be damaged when you try to remove the RJ45
waterproof connector cover with its "⇦" mark matching "▶" mark of the RJ45 waterproof jack.)
【6】 Attach the cable cover (accessory)
① Fix the cable cover to WV-Q121B/WV-Q122A or
attachment pipe using hexagon screws (4 pcs.)
(M5: accessory).
Adjust the orientation of cable cover so that the
line part of cable cover faces front of the bracket.
Line part of
IMPORTANT:
cable cover
• "Camera mounting screw (hexagon screw (M6))"
included with WV-Q121B/WV-Q122A cannot be
used. Use the "hexagon screw (M5)" included with
the camera.
• Recommended tightening torque: 2.45 N·m
{1.81 lbf·ft}
② Remove the tape as the installed auxiliary wire is
temporarily fixed to the inside of the cable cover
with tape.
* Image seen from front surface of bracket
【7】 Hang the camera at the installed auxiliary
wire of the cable cover and fix the safety wire
① Move the camera to the installation location and
hitch the installed auxiliary wire of the cable cover
to the wire hook on the upper part of camera.
Next, lower the wire stopper to prevent the
Cable
installed auxiliary wire from coming off.
cover
② Attach the safety wire of the camera to the wire
hook section of mount bracket.
* For the safety wire attachment position, refer to
Camera
operating instructions of each mount bracket.
Note:
• The camera is not fixed. Take care not to hit
RJ45
the camera against periphery (especially the
Wire hook on the upper part of camera
waterproof
dome cover).
connector cap
• Retain a work space of 500 mm {1ft 7-11/16
(accessory)
inches} or more from the cable cover when
you hang the camera from it.
• The installed auxiliary wire and the safety wire
are designed assuming the only camera body
is suspended. Do not apply other loads.
【2】Assemble 24 V AC connector kit (accessory) and connect it to the power cable
of camera body as occasion demands.
① Recommended wire rod and array of pins of connector housing (accessory)
AWG size
#24
#22
#20
#18
2
2
2
(stranded wire)
(0.22 mm
)
(0.33 mm
)
(0.52 mm
)
(0.83 mm
Wire length
20 m
30 m
45 m
75 m
Power supply connector housing
Pin No.
Signal
1
24 V AC LIVE (Brown)
2
24 V AC NEUTRAL (Blue)
3
Ground (Black)
4
Not use
② How to assemble the 24 V AC power supply connector kit
• Remove approx. 3 mm {1/8 inches} of the
Approx. 3 mm {1/8 inches}
outer jacket of the cable and twist the cable
core to prevent the short circuit first.
Upper
• Insert the tip of the cable into the point A of
the contact (accessory), and hold the cable
using the cable clamp.
• Procure either of the following tools for
clamping.
Molex manual clamp tool:
57027-5000 (For UL1015),
57026-5000 (For UL1007)
RJ45
• After clamping the contact and the cable,
waterproof
insert the contact properly into the power
connector
cap
supply connector housing.
Power supply connector housing (accessory)
(accessory)
Caution:
• A READILY ACCESSIBLE DISCONNECT DEVICE SHALL BE INCORPORATED TO THE
EQUIPMENT POWERED BY 24 V AC POWER SUPPLY.
• ONLY CONNECT 24 V AC CLASS 2 POWER SUPPLY (UL 1310/CSA 223) or LIMITED POWER
SOURCE (IEC/EN/UL/CSA 60950-1).
• ONLY CONNECT POWER OVER ETHERNET 54 V DC / PoE+ 54 V DC LIMITED POWER
SOURCE (IEC/EN/UL/CSA 60950-1).
IMPORTANT:
• The 24 V AC power supply shall be insulated from the commercial AC power.
• Be sure to use the 24 V AC power supply connector kit (accessory) provided with this product.
• After processing 24 V AC connector, actually connect it to the camera and ensure it operates
normally before using it.
• Be sure to fully insert the 24 V AC power supply connector into the power cable.
Otherwise, it may damage the camera or cause malfunction.
• When installing the camera, make sure that excessive force is not applied to the power cable.
Mount bracket
Step2 Making connections (continued)
(example: WV-Q122A)
Front of the bracket
【3】Connect 8P alarm cable (accessory) as occasion demands.
ALARM IN1 / Black & white input / Auto time adjustment input (Black) (EXT I/O 1)
GND (Brown)
ALARM IN2 / Alarm output (Red) (EXT I/O 2)
Hexagon screw
GND (Orange)
(4 pcs.)
ALARM IN3 / AUX output (Yellow) (EXT I/O 3)
(M5: accessory)
GND (Light blue or green)
Cable cover
Unused (Blue)
(accessory)
Unused (Purple)
Installed
auxiliary wire
Note:
• The default of EXT I/O terminals is "Off". Refer to the Operating Instructions on the
provided CD-ROM for further information about the EXT I/O terminal settings.
【4】Connect a microphone or external audio line to the audio input cable as
Line part of
cable cover
occasion demands.
【5】Connect a powered speaker to the audio output cable as occasion demands.
Note:
• The audio output can be switched to monitor output. The default is "Audio". Refer to the
Mount bracket
Operating Instructions on the provided CD-ROM for descriptions of how to switch the output.
(example: WV-Q122A)
• If the audio output is used for the monitor output, connect a ø3.5 mm
stereo mini connector (locally procured) to the wire as shown in the
Wire hook
section
right figure and use it.
【6】 If you use a cable other than Ethernet
cable, waterproof it.
②Safety wire
The camera body is waterproof, but the cable
ends and the inside of the mount bracket are not
waterproof. Waterproof the connection part of
①Installed
auxiliary wire
each cable.
＜Waterproof treatment＞
Waterproof by using the waterproof tape
(accessory) as shown in the right-hand figure.
IMPORTANT:
• Stretch the tape by approx. twice (see the illustra-
tion) and wind it around the cable. Insufficient tape
stretch causes insufficient waterproofing.
Wire stopper
Step3 Fixing the camera (continued)
③ Joint both sides of front/rear sunshields (accessory).
First, hook the wire side, and then hook the other
side.
2
)
IMPORTANT:
• Joint both sides of the front/rear sunshields
(accessory) before fitting in the main sunshield.
• Do not trap the safety wire inside.
④ Fix the front/rear sunshields on the camera
temporarily.
Cable
• Align the arrow (▽) with the arrow (△) of "START"
on the main sunshield to embed it, and then
rotate it toward arrow (△) of "LOCK" until it
Insert
Contact
"clicks".
A
(accessory)
Upper
Cable
⑤ Fix the front/rear sunshields on the camera using
the front/rear sunshields fixing screw (accessory).
Contact (accessory)
Recommended tightening torque:
Note:
• When removing the front/rear sunshields
(accessory), perform steps ①~⑤ in the
reverse order.
⑥ When the camera has been installed, remove the
protection sheet from the dome cover.
After removal, be sure not to touch the clear part of
the dome cover.
⑦ Turn on the power supply of camera and check the
screens of camera following Step 4 "Configure the
network settings" and adjust the angular field of
view. For details on adjustment of angular field of
view of camera, refer to Operating Instructions on
the provided CD-ROM.
Step3 Fixing the camera
【1】Attach the camera to the cable cover (accessory).
① Make the Panasonic logo mark on the
camera body face the front side and the
main sunshield rear cover (where SD memory
card is inserted) face the mount bracket side.
② Insert the positioning pins on the upper part
of camera into cable cover attachment hole.
③ Rotate the camera part in a clockwise
direction when looking from the bottom and
confirm it is temporarily fixed.
④ Tighten it securely with 3 special screws
(fixing screws) of the cable cover.
Recommended tightening torque:
Note:
• Special screw (fixing screw): As these are hexa-
gon screws, use a hexagon wrench (locally pro-
cured) "for M6".
• Bend it to the inside of the cable cover to pre-
vent the installed auxiliary wire and the wiring
section from being caught in the periphery of
N.C.
the cable cover.
【2】Attach the front/rear sunshields
Video output
GND
(accessory) to the camera.
Waterproof tape (accessory)
① Put a finger on the dent of front/rear
sunshields and unhook both sides to split it.
One side is fixed with wire to prevent loss.
Wind the tape in a
half-overlapping
manner
② Locate the front/rear sunshields to the
position that covers the cable cover.
Stretch the tape to approx.
twice its length.
x2
Precautions
• Attach the "Rain wash coating caution label" carried by the camera to the surface of the camera
(Refer to the illustration below).
Front/rear sunshields (accessory)
Main sunshield
Safety wire
Front/rear sunshields (accessory)
Live indicator
Main sunshield
Align "▽" to this "△"
The live indicator will light or blink as follows depending on the camera status.
Camera operation status
0.72 N·m {0.53 lbf·ft}
When the
power is
turned on
Front/rear sunshields fixing screw (accessory)
During the standby or connection (Cable is not connected.)
During the standby or connection (Cable is connected.) Lights green
During the upgrade process
Initialization (When the network connection is
established)
Port forwarding error caused by the UPnP function Blinks orange (in 2 seconds intervals
Trouble happening on the camera
Failure in writing data on the SD memory card
Special screw (fixing
screw) (3 pcs.)
Cable cover
(accessory)
Installed
auxiliary
Fitting hole of
wire
the cable cover:
3 points
Safety wire
Positioning
pin (3 pcs.)
Mount bracket
2.45 N·m {1.81 lbf·ft}
side
Main sunshield
rear cover
Dents
Wire
Unhook
Cable cover
START
LOCK
Front/rear sunshields
(accessory)
INITIAL SET switch
Power indicator
(OFF⇔ON)
Live indicator
SD memory card slot
Live indicator status
Lights orange → Lights off →
Before the network connection is
Blinks orange → Lights orange
established
Lights orange → Lights off →
When the network connection is
Blinks orange → Blinks green →
established
Lights green
Lights orange
Blinks orange
Lights orange → Lights off →
Blinks orange → Lights orange →
Blinks orange → Blinks green →
Lights green
(on for 1 second / off for 1 second))
Blinks red
Lights red
Advertisement
