Advertisement
Quick Links
2-Person or 4-Person Canopy Kit
Workman
Model No. 07921—Serial No. 400000000 and Up
Model No. 07922—Serial No. 400000000 and Up
Installation
1
Preparing the Machine
No Parts Required
Procedure
1.
Park the machine on a level surface.
2.
Engage the parking brake.
3.
Shut off the engine and remove the key.
4.
Disconnect the battery; refer to your Operator's
Manual.
5.
Raise the cargo bed to the dump position and
secure it with the prop rod.
2
Drilling the Holes for the
Mounting Tubes
No Parts Required
Procedure
1.
Using the dimensions shown in
hole (5/16 inch) into the outside of the floor plate
on both sides of the machine.
© 2018—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
®
GTX Utility Vehicle
Figure
1, drill 1
Register at www.Toro.com.
Figure 1
2.
Using the dimensions shown in
hole (5/16 inch) into the outside of the footboard
on the left and right sides of the machine.
Figure 2
Original Instructions (EN)
All Rights Reserved *3421-992* B
Printed in the USA
Form No. 3421-992 Rev B
Installation Instructions
Figure
2, drill 1
g259750
g259751
Advertisement
Related Manuals for Toro 07921
Summary of Contents for Toro 07921
- Page 1 Form No. 3421-992 Rev B 2-Person or 4-Person Canopy Kit Workman ® GTX Utility Vehicle Model No. 07921—Serial No. 400000000 and Up Model No. 07922—Serial No. 400000000 and Up Installation Instructions Installation Preparing the Machine No Parts Required Procedure Park the machine on a level surface.
-
Page 2: Removing The Side Panels
Installing the Front Removing the Side Panels Mounting Tubes No Parts Required Parts needed for this procedure: For Gasoline Machines Front mounting tube Important: Before performing this procedure, Flange-head bolt (5/16 x 3 inches) check your machine to see if the holes for installation already exist. - Page 3 Disconnect the vent tube and fuel line from the Remove the 4 screws securing the left side tank (Figure panel to the lower seat assembly (Figure Note: Prepare to capture and clean up any fuel that spills when you disconnect the fuel line from the tank.
- Page 4 Remove the 2 flange-head bolts securing the battery tray to the frame (Figure g035126 Figure 9 1. Right side panel 2. Self-tapping screw g033999 Figure 8 Remove the 2 bolts securing the charger bracket 1. Flange-head bolt 3. Right side panel to the battery tray (Figure 10).
- Page 5 Drilling the Support Bracket No Parts Required Procedure Drill the support bracket using the measurements shown in Figure When you drill the highest upper hole, ensure that you drill all the way through the outer bracket, frame tube, and firewall. CAUTION Use caution when drilling the holes into the right side of the frame on an electric machine.
-
Page 6: Installing The Side Panels
Installing the Side Panels No Parts Required For Gasoline Machines Secure the right side panel using the previously removed 4 screws (Figure Secure the battery tray to the frame using the previously removed 2 flange-head bolts (Figure Secure the battery cables using the previously removed 2 bolts and 2 nuts and connect the battery terminals (Figure... - Page 7 Secure the tube-mounting bracket to the rear mounting tubes using 2 flange-head bolts (5/16 x 3 inches) and 2 flange nuts (5/16 inch) as shown in Figure Installing the Rear Install the trim seal onto the tube-mounting bracket (Figure 13). Mounting Tubes and Tube-Mounting Bracket Parts needed for this procedure:...
- Page 8 Installing the Long Canopy Support Brackets For a 4-Person Canopy Only Parts needed for this procedure: Long canopy support bracket Hex-washer head bolt (5/16 x 3/4 inch) Trim seal Procedure Secure the 2 long canopy support brackets to the front and rear mounting tubes using 8 hex-washer head bolts (5/16 x 3/4 inch) as shown in Figure Install the 2 trim seals onto the 2 long canopy support brackets...
-
Page 9: Installing The Canopy
Installing the Canopy Parts needed for this procedure: Canopy Flange-head bolt (1/4 x 1-3/4 inches) Sealing washer Locknut (1/4 inch) Procedure Important: If you are installing a mirror kit, install it before installing the canopy. Secure the canopy to the front and rear mounting tubes using 4 flange-head bolts (1/4 x 1-3/4 inches), 4 sealing washers, and 4 locknuts (1/4 inch) as shown in Figure g259844... - Page 10 Installing the Canopy Support Bracket Parts needed for this procedure: Canopy support bracket Flange-head bolt (1/4 x 2-1/4 inches) Locknut (1/4 inch) Sealing washer Trim seal Spacer (1/4 inch) Procedure Install the trim seal onto the tube-mounting bracket (Figure 16). g259845 Figure 16...
- Page 11 Secure the canopy support bracket to the front support tubes and canopy using the 2 flange-head bolts (1/4 x 2-1/4 inches), 2 spacers (1/4 inch), 2 sealing washers, and 2 locknuts (1/4 inch) as shown in Figure g259846 Figure 17 2-person canopy shown 1.
- Page 12 Installing the Canopy Support Tube For a 4-Person Canopy Only Parts needed for this procedure: Canopy support tube Locknut (1/4 inch) Sealing washer Flange-head bolt (1/4 x 1-1/2 inches) Foam pad Flange-head bolt (1/4 x 1-1/4 inches) Procedure Apply the foam pad to the canopy support tube (Figure 18).
- Page 13 Secure the canopy support tube to the long canopy support brackets using 4 flange-head bolts (1/4 x 1-1/4 inches) and 4 locknuts (1/4 inch) as shown in Figure g262068 Figure 19 1. Long canopy support bracket 3. Locknut (1/4 inch) 2.
- Page 14 Notes:...
- Page 15 Notes:...
- Page 16 Countries Other than the United States or Canada Customers who have purchased Toro products exported from the United States or Canada should contact their Toro Distributor (Dealer) to obtain guarantee policies for your country, province, or state. If for any reason you are dissatisfied with your Distributor's service or have difficulty obtaining guarantee information, contact the Toro importer.