Table of Contents
Advertisement
Available languages
Available languages
To Change Blades (Fig. A, I–L)
WARNING: To reduce the risk of serious personal
injury, turn tool off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can cause injury.
CAUTION: Planer blades are extremely sharp. Handle
with great care.
CAUTION: Be sure that the blades are mounted as
described in the instruction manual.
CAUTION: Inspect blades, carriers, guide bars, screws
and drum covers for straightness and defects. Do not
use any components that are suspect in any way.
CAUTION: Carefully tighten all screws when attaching
blades to the tool. Always check to make sure they are
tightened securely.
CAUTION: Use planer blades of the same weight and
dimensions, otherwise drum vibration/oscillation
could cause poor planing action and tool breakdown
can result.
The planer is capable of using high-speed steel and carbide
blades. Be sure to check the planer to verify which blade it is
fitted with.
Blade Storage (Fig. A, I)
Your planer is equipped with blade storage for two
additional blades. To store or remove additional blades, turn
the blade storage knob
13
High‑Speed Steel Blades (Fig. A, J, L)
1. To Remove Blade from Planer (Fig. J1, J2)
a. Loosen and remove the three star head screws
with the T25 star head key
drum cover
from the drum
19
b. Remove the guide bar/high-speed steel blade
assembly (
21
,
22
2. To Adjust Blade Using Gauge Plate (provided with
tool) (Fig. J3)
a. Place the guide bar/high-speed steel blade assembly
on the gauge plate
high-speed steel blade flush against the gauge plate
inside wall
25
. The heel of the guide bar
overlap the end of the gauge plate
b. Loosen the two cross-shaped screws
a screwdriver.
c. Simultaneously hold the blade edge
gauge plate inside wall
bar
23
against the back edge of the gauge plate.
Securely tighten the cross-shaped screws
3. To Reinstall Blade (Fig. J1, J2)
a. Cautiously remove the adjusted guide bar/high-speed
steel blade assembly from the gauge plate
place the heel of the guide bar
the drum
20
.
b. Set the drum cover
high-speed steel blade assembly and securely tighten
the three star head screws
counterclockwise to open.
provided. Remove the
16
.
20
,
23
).
24
with the cutting edge of the
23
24
.
22
with
21
against the
25
and the heel of the guide
22
24
23
into the groove in
19
over the adjusted guide bar/
18
to the drum.
4. Repeat procedure for the other blade.
NOTE: In order to use high-speed steel blades with this
planer, the sharpening holder
high-speed steel blades and is available at additional cost
from your local D
Reversible Carbide Blades (Fig. A, K)
1. To Remove Blade from Planer (Fig. K2)
a. Loosen and remove the three star head screws
with the T25 star head key
drum cover
b. Remove the blade carrier/guide bar assembly
(
,
22
2. To Adjust Blade Using Gauge Plate (provided with
tool) (Fig. K3)
a. Cautiously place the sharp edge of the carbide
blade
side of the carbide blade facing up. Either edge of the
reversible carbide blade can be set flush against the
gauge plate inside wall
b. Place the blade carrier/guide bar assembly on the
blade so that the rib on the blade carrier
the groove on the carbide blade
guide bar
plate
c. Loosen the two cross-shaped screws
a screwdriver.
d. Simultaneously hold the blade carrier
blade
while holding the heel of the guide bar
the back edge of the gauge plate. Securely tighten
18
the cross-shaped screws
3. To Replace the Blade (Fig. K1, K2)
a. Remove the adjusted blade carrier/guide bar
assembly from the gauge plate
of the guide bar
b. Place the drum cover
guide bar assembly. Loosely screw the three star head
screws
gap between the drum and the blade carrier
c. Slide the carbide blade between the drum
will
the blade carrier
the blade carrier sets into the groove in the blade.
d. Center the carbide blade
carrier
housing on both sides.
e. Securely tighten the three star head screws
the drum.
.
4. Repeat procedure for the other blade.
NOTE: Before installing or replacing blades, clean out all
chips or any foreign matter adhering to the planer blade
and
or drum.
NOTE: If your planer is not fitted with carbide blades,
the blade carrier
available at additional cost from your local D
authorized service center.
28
is required to sharpen
WALT authorized service center.
e
16
19
from the drum
,
). Carefully remove the carbide blade
23
27
on the gauge plate
27
24
.
25
23
will overhang the end of the gauge
24
.
27
against the gauge plate inside wall
22
.
23
into the groove on the drum
over the blade carrier/
19
into the drum
so that there is a small
18
20
26
from the side so that the rib on
under the blade
27
making sure the blade is clear of the tool
26
26
required for carbide blades is
ENGLISH
18
provided. Remove the
20
.
.
27
with the grooved
26
fits into
27
. The heel of the
with
22
26
and carbide
25
23
against
24
and place the heel
20
.
.
26
20
and
18
to
WALT
e
11
Advertisement
Table of Contents
