JVC GR-DVL100U Manual page 20

Audio/Video
Tos
'able
(provided)
S-Video cable
(optional)
White to
AUDIO LIN
To Yellow to Red to
S-VIDEO IN VIDEO IN Be AUDIO R
if
Connect when an S-Video cable is not used.
" * When connecting the cables, open this cover.
(OTT ING:
Dubbing To A VCR
Following the illustration, connect the camcorder and
the VCR. Also refer to pg. 34 and 35.
Set the camcorder's Power Switch to " EQ" while
pressing down the Lock Button located on the switch,
'turn on the VCR's power, and insert the appropriate
cassettes in the camcorder and the VCR.
3 Engage the VCR's AUX and Record-Pause modes.
Pa § Engage the camcorder's Play mode to find a spot just
before the edit-in point. Once it is reached, press
®/U on the camcorder,
fox) Press P/II on the camcorder and engage the VCR's
F894 Record mode.
Engage the VCR's Record-Pause mode and press
»/I8 on the camcorder.
Repeat steps 4 through 6 for additional editing, then
stop the VCR and camcorder when finished.
NOTES:
© Use the provided Audio/Video cable, making sure to
connect the end with a core filter to the camcorder. The
core filter reduces interference.
© You can use Playback Zoom (= pg. 42) or Playback
Special Effects (CF pg. 43) in step 5.
© Before you start dubbing, make sure that the indications
do not appear on the connected TV. If they do, they are
being recorded onto the new tape.
To choose whether or not the following displays appear
'on the connected TV...
* Date/Time
vn Set "DATETIME" to "ON" or "OFF in the Menu
Screen (7 pg. 32).
ime Code
set "TIME CODE' to "ON" or "OFF" in the Menu
Screen (CF pg, 32).
'Playback Sound Mode, Tape Speed And Tape Running
Displays
vn Set "ON SCREEN' to "LCD" or "SIMPLE" in the
Menu Screen (CF pg. 32). Or, press DISPLAY on the
remote control.
To DV IN/OUT
Core filter
DV cable
(optional)
a filter
i t equipped
To Use This Camcorder As A Recorder . . .
1. Turn the Power Switch to "El
a EN
Dubbing To Or From A Video Unit Eq
With A DV Connector (Digital Dubbing)
Itis also possible to copy recorded scenes from the
camcorder onto another video unit equipped with a DV
connector. Since a digital signal is sent, there is little if any
image or sound deterioration.
[To use this camcorder as a player]
fp Make sure the camcorde's power i of
Connect the camcorder to your video unit equipped
with a DV connector using a DV cable as shown in
the illustration.
i Fess >to lay back the source tape
While watching the playback on the monitor, engage
the DV connecior-equipped video unit's record mode
from the spot on the source tape you want to begin
recording,
NOTES:
© itis recommended to use the AC Power Adapter/Charger as
the power supply instead of the battery pack (7 pg. 9).
© If the remote control is used when both the player and
recorder are JVC video units, both units will perform the
same operation. To prevent this from happening, press the
buttons on both units.
© For Digital Dubbing, this camcorder can be connected only
to one device at a time. This camcorder can also be used as
a recorder.
Ifa blank portion or disturbed image is played back on the
player during dubbing, the dubbing may stop so that an
unusual image is not dubbed.
@ Even though the DV cable is connected correctly, some-
times the image may not appear in step 3. f this occurs, turn
off the power and make connections again.
© If "Playback Zoom" (1 pg. 42), "Playback Special Effects"
(EF pg, 43) or "Snapshot" is attempted during playback,
only the original playback image recorded on the tape is
output from the DV IN/OUT connector.
'© When using a DV cable, be sure it has a core filter
attached. The core filter eeduces interference.
while pressing down the Lock Button located on the switch.
2, Set "REC MODE" to "SP" or "LP" in the Menu Screen (C# pg. 32)
3. Connect the DV cable as shown in the illustration and load a cassette to record on.
4, Press the Recording Start/Stop button to engage the Record-Pause made. "DV. IN" appears on the screen.
5, Press the Recording Stary/Stop button to start recording. "DV. IN" changes to "
6, Press the Recording Starv/Stop button again to engage the Record-Pause mode. " EXAIN" returns to
"DV, IN".
NOTES:
© Digital Dubbing is performed in the sound mode recorded on the original tape, regardless of the current
"SOUND MODE" setting (CF pg. 23).
'© During Digital Dubbing, no signals are output from the video or audio connectors.