JVC GR-DVL100U Manual page 29

30.
appear all over the LCD.
monitor or the viewfinder.
FROUBLESHOOTING (coni
Cepeetas
PSSIBEE |
The LCD monitor and the
viewfinder are made with
high-precision technology.
However, black spots or
bright spots of light (red,
green or blue) may appear
Constantly on the LCD
monitor or the viewdinder.
These spots are not recorded
con the tape. This is not due to
any defect of the unit.
(Effective dots: more than
99.99 %)
ome
30.
39. An error indication
(€01 — £06) appears.
POs
39. *A malfunction of some kind
has occurred. In this case
the camcorder's functions
become unusable.
mar:
'* Remove the power supply
(battery pack, etc.) and wait a
few minutes for the indication
to clear. When it does, you
can resume using the
camcorder.
Ifthe indication remains even
though you repeat the above
two or three times, please
consult your nearest VC
dealer.
40, The charger indicator on
the AC Power Adapter/
31. During recording, sound
cannot be heard,
© This is normal.
a. Charger does not light.
32. Play, Rewind and Fast-
Forward functions do not
work.
. * The Power Switch is not set
to" i".
32, # Set the Power Switch to
40. « The temperature of the
battery is extremely high/low.
'Charging is dificult in
places subject to extremely
high/low temperatures.
} . *To protect the battery, itis
recommended to charge it
in places with a temperature
of 10°C to 35°C (50°F to
95°F) ( pg. 64).
GED" (CF pg. 31). 41, Picture does not appear on
the LCD monitor.
33. The tape is moving, but
there is no picture.
. # Your TV has AV input
terminals, but is not set to its
VIDEO mode.
* The cassette holder cover is
open.
33, ¢ Set the TV to the mode
or channel appropriate
ck
for video play!
(> pg. 34, 35).
* Close the cassette holder
41. The lens cap is attached.
The LCD monitor's
brightness setting is too
dark.
| . *Remove the lens cap
( pg. 14).
© Adjust the brightness of the
(F pg. 14),
r is tilted
upward 180 degrees, open
the monitor fully (= pg. 15).
cover (CF pg. 12). 42, When the image is printed
34. The LCD monitor image is 34.
distorted.
* During playback of the
unrecorded portion, High-
speed Search and still
playback, LCD monitor
indications appear distorted.
This is not a defect.
from the printer, a black
#4.
bar appears at the bottom
oF the screen,
42, » This is not a malfunction. . + By recording with "DiS"
activated (7 pg. 24) this
can be avoided:
43. When the camcorder is
connected via the DV
connector, the camcorder
35. Images on the LCD. 35.
monitor are jittery.
The speaker volume is too
great.
does not o p e r a t e .
35. «Turn the speaker volume
loes not operate.
down (¥ pg. 31).
36. Blocks of noise appear 36.
during playback, or there is
no playback picture and
the screen becomes blue.
36. #Clean the video heads with
an optional cleaning
cassette (C7 pg. 65).
37. The LCD monitor, the
viewfinder and the lens
have become dirty (ex.
fingerprints)
37. «Wipe them gently with soft
cloth. Wiping strongly can
cause damage (7 pg. 58).
38. An unusual mark appears. 38, © Check the section of the
manual that explains LCD.
monitor/viewfinder
indications (C7 pg. 59 - 61).
43, ¢ The DV cable was plugged/
unplugged with power
tured on.
. * Turn the camcorder's power
off and on again, then
operate it.