Mitsubishi Electric CITY MULTI PUHY-P72-432TNU-A Data Book page 11

1. SPECIFICATIONS
Outdoor Model
Indoor Model
Power source
Cooling capacity
(Nominal)
Power input
(208-230) Current input
(Rated)
Power input
(208-230) Current input
Temp. range of Indoor
cooling Outdoor
Heating capacity
(Nominal)
Power input
(208-230) Current input
(Rated)
Power input
(208-230) Current input
Temp. range of Indoor
heating *3 Outdoor
Indoor unit Total capacity
connectable Model/Quantity
Sound power level (measured in anechoic room) *4
Refrigerant Liquid pipe
piping diameter Gas pipe
Set Model
Model
Minimum Circuit Ampacity
Maximum Overcurrent Protection
FAN Type x Quantity
Airflow rate
Control, Driving mechanism
Motor output
*5 External static press.
Compressor Type x Quantity
Manufacture
Starting method
Motor output
Case heater
Lubricant
External finish
External dimension H x W x D
Protection High pressure protection
devices Inverter circuit (COMP./FAN)
Fan motor
Refrigerant Type x original charge
Control
Net weight
Heat exchanger
HIC circuit (HIC: Heat Inter-Changer)
Pipe between unit and Liquid pipe
distributor Gas pipe
Defrosting method
Drawing External
Wiring
Standard Document
attachment Accessory
Optional parts
Remarks
Notes:
1.Nominal cooling conditions (Test conditions are based on AHRI 1230)
Indoor: 80°FD.B./67°FW.B. (26.7°CD.B./19.4°CW.B.), Outdoor: 95°FD.B. (35°CD.B.)
2.Nominal heating conditions (Test conditions are based on AHRI 1230)
Indoor: 70°FD.B. (21.1°CD.B.), Outdoor: 47°FD.B./43°FW.B. (8.3°CD.B./6.1°CW.B.)
3.When applying product below -4°F, consult your design engineer for cold climate application best practices,
including the use of a backup source for heating.
4.Cooling mode/Heating mode
5.External static pressure option is available (0.12 in.WG, 0.24 in.WG, 0.32 in.WG/30 Pa, 60 Pa, 80 Pa).
* Due to continuing improvement, above specifications may be subject to change without notice.
MEES23K040
Non-Ducted
*1 BTU/h
kW
kW
A
BTU/h
kW
kW
A 47.3-42.8
W.B.
D.B.
*2 BTU/h
kW
kW
A
BTU/h
kW
kW
A 51.8-46.9
D.B.
W.B.
dB <A>
in. (mm)
in. (mm)
PUHY-P120TNU-A (-BS)
A
A
Propeller fan x 2
cfm
3
m /min
L/s
Inverter-control, Brushless DC motor
kW 0.46+0.46
0 in.WG (0 Pa)
Inverter scroll hermetic compressor x 1
MITSUBISHI ELECTRIC
Inverter
kW 7.7 x 1
kW
MEL32
Pre-coated galvanized steel sheet (+powder coating for -BS
<MUNSELL 3Y 7.8/1.1 or similar>
in. 71-5/8 x 48-7/8 x 29-3/16
mm 1,818 x 1,240 x 740
High pressure sensor, High pressure switch at 4.15 MPa
(601 psi)
Over-current protection
R410A x 21 lbs + 9 oz (9.8 kg)
lbs (kg) 605 (274)
Salt-resistant cross fin & copper tube
Copper pipe, tube-in-tube structure
in. (mm) 1/2 (12.7) Brazed
in. (mm) 1-1/8 (28.58) Brazed
KE94G655
Details on foundation work, duct work, insulation work, electrical wiring, power source switch, and other items shall be
referred to the Installation Manual.
PUHY-P216TSNU-A (-BS)
3-phase 3-wire 208-230 V ±10% 60 Hz
216,000
63.3
16.78
51.7-46.8
206,000
60.4
15.36
59~75°F (15~24°C)
23~126°F (-5~52°C)
243,000
71.2
18.63
57.4-51.9
232,000
68.0
16.82
59~81°F (15~27°C)
-13~60°F (-25~15.5°C)
50~130% of outdoor unit capacity
P04~P96/2~50
81.5/83.0
5/8 (15.88) Brazed
1-1/8 (28.58) Brazed
50-46
80-70
7,750
220
3,670
-
Pre-coated galvanized steel sheet (+powder coating for -BS
type)
High pressure sensor, High pressure switch at 4.15 MPa
-
LEV and HIC circuit
Auto-defrost mode (Reversed refrigerant cycle)
KL94T773
Installation Manual
Details refer to External Drw
Outdoor Twinning kit: CMY-Y100CBK3
joint: CMY-Y102SS/102LS-G2,CMY-Y202S/302S-G2
Header: CMY-Y104/108/1010C-G
Y-Series
Ducted
15.71
48.4-43.8
17.68
54.5-49.3
PUHY-P96TNU-A (-BS)
40-36
60-50
Propeller fan x 2
6,700
190
3,170
Inverter-control, Brushless DC motor
0.46+0.46
0 in.WG (0 Pa)
Inverter scroll hermetic compressor x 1
MITSUBISHI ELECTRIC
Inverter
5.5 x 1
-
MEL32
type)
<MUNSELL 3Y 7.8/1.1 or similar>
71-5/8 x 48-7/8 x 29-3/16
1,818 x 1,240 x 740
(601 psi)
Over-current protection
-
R410A x 21 lbs + 9 oz (9.8 kg)
580 (263)
Salt-resistant cross fin & copper tube
Copper pipe, tube-in-tube structure
3/8 (9.52) Brazed
7/8 (22.2) Brazed
KE94G655
Unit converter
BTU/h =kW x 3,412
3
cfm =m /min x 35.31
lbs =kg/0.4536
*Above specification data is
subject to rounding variation.
8