Philips 55PW9383 Directions For Use Manual page 74

F_yllOw the steps below to connect a cable converter box to
our TV.
To make the connections in this example, you will need one coaxi-
al cable (75£)).
NOTE: The coaxial cable is not supplied with your TV. You should be
able to buy one at most stores that sell electronics. Or you can call our
Customer Care Center at 1-800-531-0039.
2
3
Connect your cable TV signal to the INPUT jack on the
back of the cable converter box.
Connect a coaxial cable from the OUTPUT jack on the
back of the cable converter box to the ANTENNA IN 75_
jack on the rear of the TV.
Insert the TV's power plug into the wall socket.
Coaxial Cable Coaxial Cable
Leadqn from
NOTE: This example shows the type ofc_le converter
box most commonly used. The RF outputs on cable convert-
er boxes, usually labeled "OUTPUT" or "TO TV," will not
pass a stereo sound signal to the TV. it; however, your cable
converter box has separate Audio/Video outputs, using A/V
cables to connect to those outputs and to the,*ZV inputs on
the TV might pass a stereo sound signal to the 'IV. Contact
your cable TV company for more information.
Rear of TV
D
USING THE
TV
BUTTONS
S_ould your remote control be lost or broken, you can still
hange some of the basic picture and sound settings with the
buttons on the TV. Follow the steps below to jamiliarize yourself
with the.[unctions qf the TV buttons.
3
4
Press POWER/STANDBY to turn the TV on (or off).
Allow about 10 seconds for the TV to power on.
Press the VOLUME + or - buttons to decrease or
increase the sound level.
Press the VOLUME + and buttons simultaneously to dis-
play the on-screen menu. After the menu appears, use these
buttons to enter submenus and make selections or adjust-
ments. (Use the CHANNEL buttons to move up and down
in the menu or submenus.) Press both VOLUME buttons
simultaneously to back out of the on-screen menus.
Press SOURCE SELECT to choose from among the sig-
nal inputs you have connected to the TV.
Press the CHANNEL buttons to select TV channels.
L--MENU_
Remote Sensor Power Standby
Window Button
You can press any of the bu_ons on
the front of the TV to turn the TV
on, but you must press the
Power/Standby button to turn the
set ofl:
As shown in the illustration below,
pressing the VOLUME - and
SOURCE SELECT buttons simul-
taneously activates Auto
intelliSense
TM.
This feature auto-
matically adjusts the picture's con-
vergence (color alignment) if the
picture appears fuzzy. For more on
Auto IntelliSense
TM,
see page 7.
Auto IntelliSense is a trademark
of Philips Consumer Electronics
Company. Copyright 2002
Philips Consumer Electronics.
INSTALLING BATTERIES
T_ load the supplied batteries into the remote, .ibllow these
eps.
2
3
Gently press and hold the indention on the back of the
remote and slide the battery cover off the remote.
Place the two "AA" size batteries in the remote's bat-
tery case. Ensure that the (+) and (-) ends of the batteries
line up correctly with the (+) and ( ) inside the case;
Slide the battery cover back into place.
POINTING THE REMOTE
Press the TV mode button on the remote to ensure that the
remote sends its commands to the TV. When operating the remote
control, point the remote toward the remote sensor window on the
TV.
® ®
OSAG CAOTION
To prevent battery leakage that
may result in injury to you or dam-
age to the remote control:
Install ALL batteries correctly, + and -,
as marked on the unit.
Do not mix batteries (OLD and NEW
or CARBON and ALKALINE, etc.)
Remove batteries when the remote
control is not used for a long time.
Do not take apart, heat, or put bat-
teries in fire.
Be sure to point the remote toward the
sensor window on the TV or accessory
device you wish to operate.
Press the correct mode button for the
device: TV, VCR, ACC (for accessories
other than VCRs).
Be within about 30 feet (10 meters) of
the TV or accessory device you are
using the remote to operate.
Avoid dropping the remote on hard sur-
faces.
Do not use harsh chemicals to clean the
remote. Use only a soft, lightly mois-
tened cloth.