JVC KM-H2500 Manual page 41

Memory AI and Recall to Preview Scenarios
Table 8 shows the contents of a memory register and
the state of the switcher in various scenarios.
Table 8 Recall to Preview Scenarios
Memory
Element
Register
Input 2
PST Bus
Input 3
PGM Bus
Input 4
Key 1
Input 5
Key 2
–
Key 3
Depending on the Recall to Preview setting, the
elements recalled are as follows:
Recall to Preview Off
• Scenario 1
› Input 2 is recalled to the Preset bus.
› Input 3 is recalled to the Program bus (on-air
image instantly cuts to Input 3).
› Input 4 is recalled to Key 1 (on-air image
instantly cuts to Input 4).
› Input 5 is recalled to Key 2 (on-air image not
affected as Key 2 is off-air).
• Scenario 2
› Input 2 is recalled to the Preset bus.
› Input 3 is recalled to the Program bus (on-air
image instantly cuts to Input 3).
› Input 4 is recalled to Key 1 (on-air image is not
affected as Key 1 is off-air).
› Input 5 is recalled to Key 2 (on-air image is not
affected as Key 2 is off-air).
Recall to Preview On
• Scenario 1
› Input 2 is recalled to the Preset bus.
› Input 3 is not recalled to the Program bus (on-air
image is not affected).
› Input 4 is not recalled to Key 1 as Key 1 is on-air
(on-air image is not affected).
› Input 5 is recalled to Key 2 (on-air image is not
affected as Key 2 is off-air).
• Scenario 2
› Input 2 is recalled to the Preset bus.
› Input 3 is not recalled to the Program bus (on-air
image is not affected).
› Input 4 is recalled to Key 1 (on-air image is not
affected as Key 1 is off-air).
› Input 5 is recalled to Key 2 (on-air image is not
affected as Key 2 is off-air).
Scenario
1 2
Any Input Any Input
Input 1 Input 1
(on-air) (on-air)
Input 6 –
(on-air)
– –
Memory AI
• Scenario 1
› Input 3 is recalled to the Preset bus (on-air
image is not affected).
› Input 4 is recalled to Key 2 as Key 1 is on-air
(on-air image is not affected).
› KM-H3000: Input 5 is recalled to Key 3 as Key 2
is now in-use (on-air image is not affected).
› KM-H2500: Input 5 is not recalled as both keys
are now in use.
› Next Transition area is set to transition
background, Key 1 off-air, Key 2 on-air, and Key
3 on-air (KM-H3000 only).
• Scenario 2
› Input 3 is recalled to the Preset bus (on-air
image is not affected).
› Input 4 is recalled to Key 1 (on-air image is not
affected).
› Input 5 is recalled to Key 2 (on-air image is not
affected).
› Next Transition area is set to transition
background, Key 1 on-air, and Key 2 on-air.
To set the Memory AI or Recall to Preview mode:
1
4
2
1. Press RECALL.
2. Press NEXT.
3. Push the RclPv knob to select the Recall to
Preview Mode. You can choose from the
following:
• On — Enables Recall to Preview mode.
• Off — Disables Recall to Preview and
Memory AI modes.
• MemAI — Enables Memory AI mode.
4. Select the memory register you wish to recall
from as follows:
• If you are using Bank Mode, press one of the
10 Wipe Pattern buttons to designate the
memory register in the selected bank. You
may also use the Bank knob to change the
selected bank before storing.
• If you are using Direct Access Mode, press
one of the 10 Wipe Pattern buttons to
designate the desired bank and then press a
3
35