Motorola 110502USM001 - Vanguard 60 Router User Manual page 56

Configuration
Step (continued)
Configure the Configure --> Configure
LCON LAN Connections -->
Configure LAN Connection
Parameter
Configure --> Configure
LAN Connections -->
Configure LAN Connection
Table
Configure the Configure --> Configure
Mnemonic Table Network Service -->
Configure Mnemonic Table
Configure the Configure --> Configure
Router Interface Router --> Configure
Router Interface State
Configure --> Configure
Router --> Configure IP -->
Interface
Configure the Configure --> Configure
Route Selection Network Services -->
Table Route Selection Table
Configuration Tips These tips may be useful when configuring the example above:
3-6
Menu Node 100
Maximum Number of LAN
Connections: 32 (Default)
Entry Number: 1
Interface Number: 5
LAN Forwarder Type: ROUT
LAN Connection Type:
PT-to-PT
Entry Number:2
Interface Number: 6
LAN Forwarder Type: ROUT
LAN Connection Type:
PT-to-PT
N/A
Interface #1 State: Enabled
Interface #5 State: Enabled
Interface #6 State: Enabled
Entry Number: 1
Interface : 1
IP Address: 10.33.6.10
Entry Number: 2
Interface: 5
IP Address: 10.33.1.1
Entry Number: 2
Interface: 6
IP Address: 10.33.2.1
Entry Number:1
Address: 10094
Destination: LCON
• Remote Connection ID - the Remote Connection ID specifies exactly where
within the receiving node the call is to terminate. You specify the Remote
Connection ID in the LAN Connection Table for the node that initiates call. In
this example, for Node 200, you must specify a Remote Connection ID of 1
which corresponds to Node 100's LCON-1 or Entry 1 of the LAN Connection
Table.
• Route Selection Table - the function of the Route Selection Table is to allow
the X.25 Call request to be routed within the node. The Route Selection Table
can be configured to pass the X.25 Call Request to a WAN Port (FRI-1s1) or
to an endpoint within the node, the LCON. Therefore, for Node 200 and 300,
which initiates calls, specify the X.25 calling address and the WAN Port as the
Destination. For the Node 100, which receives calls, specify the X.25 called
address and the LCON as the destination.
• Router Interface - for WANView, specify a router interface for each WAN
link. If for example you add additional nodes to the network, Node 400 and
500, you will be required to enable and configure two more interfaces
(interface 7 and 8) at Node 100.
Node 200
Maximum Number of LAN
Connections: 32 (Default)
Entry Number: 1
Interface Number: 5
LAN Forwarder Type: ROUT
LAN Connection Type:
PT-to-PT
Autocall Mnemonic: Call100
Maximum Number of Autocall
Attempts: 0
Remote Connection ID: 1
Entry Number: 1
Mnemonic Name: Call100
Call Parameter: 10094
Interface #1 State: Enabled
Interface #5 State: Enabled
Entry Number: 1
Interface : 1
IP Address: 10.33.7.10
Entry Number: 2
Interface: 5
IP Address: 10.33.1.2
Entry Number: 1
Address: 100
Destination: FRI-1s1
Priority 1
Configuring a Vanguard Router
Node 300
Maximum Number of LAN
Connections: 32 (Default)
Entry Number: 1
Interface Number: 5
LAN Forwarder Type: ROUT
LAN Connection Type:
PT-to-PT
Autocall Mnemonic: Call100
Maximum Number of Autocall
Attempts: 0
Remote Connection ID: 2
Entry Number: 1
Mnemonic Name: Call100
Call Parameter: 10094
Interface #1 State: Enabled
Interface #5 State: Enabled
Entry Number: 1
Interface : 1
IP Address: 10.33.10.10
Entry Number: 2
Interface: 5
IP Address: 10.33.2.2
Entry Number: 1
Address: 100
Destination: FRI-1s1
Priority 1