Related Manuals for Fujitsu SK-96620_350-64PMC(1)
Summary of Contents for Fujitsu SK-96620_350-64PMC(1)
- Page 1 Fujitsu Semiconductor Europe FMEMCU-UG-960028-12 User Guide F²MC-16LX/FX FAMILY MB96620/350 SERIES MB90350 SERIES EVALUATION BOARD SK-96620_350-64PMC(1) USER GUIDE...
-
Page 2: Revision History
V1.2, SWi: new chapter about CE conformity declaration This document contains 47 pages. Abbreviations / Definitions microcontroller MB96600 F²MC16FX Fujitsu 16-bit microcontroller 300 super series MB96300 F²MC16FX Fujitsu 16-bit microcontroller 600 super series MB966xx Derivate of MB96600 super series MB963xx... -
Page 3: Warranty And Disclaimer
Product or parts thereof, if the Product is returned to Fujitsu Semiconductor Europe GmbH in original packing and without further defects resulting from the customer‟s use or the transport. -
Page 4: Table Of Contents
LIN”A”, LIN”B” Interface connector (X6, X8) ............32 CAN”A”, CAN”B” Interface connector (X10, X11)........... 32 USER-LEDs & LC-Display (optional) ..............32 In-Circuit-Programming Connector (X17) .............. 33 Debug Connector (X21) ..................33 © Fujitsu Semiconductor Europe GmbH - 4 - UG-960028-12... - Page 5 List of Figures ......................43 Table of Figures ....................43 8 INFORMATION IN THE WWW..................44 9 EU-KONFORMITÄTSERKLÄRUNG / EU DECLARATION OF CONFORMITY ..... 45 10 CHINA-ROHS REGULATION ..................46 11 RECYCLING ........................47 © Fujitsu Semiconductor Europe GmbH - 5 - UG-960028-12...
-
Page 6: Overview
Chapter 1 Overview 1 Overview 1.1 Abstract The SK-96620_350-64PMC(1) is a multifunctional evaluation board for the Fujitsu F²MC- 16FX Flash microcontroller MB96620 series and MB96350 series as well as 16LX Flash microcontroller MB90350 series. It can be used stand alone for software development and testing or as a simple target board to work with the emulator system. -
Page 7: Features
SK-96620_350-64PMC(1) User Guide Chapter 1 Overview 1.2 Features Supports following Fujitsu products: F²MC-16FX Microcontroller MB96620 Series with in FPT-64P-M23/24 package Embedded Emulator MB2100-01-E F²MC-16FX Microcontroller MB96350 Series with in FPT-64P-M23/24 package MB2198 Emulator System with the Probe Cable MB2198-504 ... -
Page 8: General Description
In case of the MB963xx and 16LX microcontroller the board can be used as an emulator target board. In this case the microcontroller must be removed from the socket and the corresponding probe cable has to be mounted. © Fujitsu Semiconductor Europe GmbH - 8 - UG-960028-12... - Page 9 1.3.9 On-Chip Debug System (OCDS) If the On-Chip debugging on the MB96600 super series is used, then the embedded emulator MB2100-01-E must be connected to the target board via SMA jack. © Fujitsu Semiconductor Europe GmbH - 9 - UG-960028-12...
-
Page 10: Installation
Do not screw the cover too tight (max 0.054 Nm). If you have connectivity problems then please loosen the screws and tighten again the screws equally. Do not clean NQPACK, YQPACK, and YQSOCKET with steam. Cleaning material will contaminate inside of connector. © Fujitsu Semiconductor Europe GmbH - 10 - UG-960028-12... -
Page 11: Default Jumper Settings
Closed Closed Closed LIN “B” VBAT JP45 Jumper 2 pin Open Open Open LIN “A” VBAT JP46 Jumper 2 pin Open Open Open JP47 Power Jumper 2 pin Closed Closed Closed © Fujitsu Semiconductor Europe GmbH - 11 - UG-960028-12... - Page 12 CAN “B” TxD: TX2 JP60 Jumper 2 pin Closed Closed Open *1: If JP51B is assembled, then JP51A must be open, because both jumpers are in parallel. Table 2-1: Default Jumper Settings © Fujitsu Semiconductor Europe GmbH - 12 - UG-960028-12...
-
Page 13: Jumper Location
The following pictures show the silk plot of the starter-kit with marked default jumper settings depending on the applied microcontroller series. 2.2.1 MB96620 Series Figure 2-1: Default Jumper Settings with MB96620 Series © Fujitsu Semiconductor Europe GmbH - 13 - UG-960028-12... - Page 14 SK-96620_350-64PMC(1) User Guide Chapter 2 Installation 2.2.2 MB96350 Series Figure 2-2: Default Jumper Settings with MB96350 Series © Fujitsu Semiconductor Europe GmbH - 14 - UG-960028-12...
- Page 15 SK-96620_350-64PMC(1) User Guide Chapter 2 Installation 2.2.3 MB90350 Figure 2-3: Default Jumper Settings with MB90350 Series © Fujitsu Semiconductor Europe GmbH - 15 - UG-960028-12...
-
Page 16: Location Of Components
Connector (X21) DIP Switch 3.3V LED (S2) (LD9) VCC LED (LD11) Pin Header Pin Header (X2) (X1) Main Clock (Q1) Sub Clock (Q2) VG96 male (X4) Figure 3-1: Location of Components © Fujitsu Semiconductor Europe GmbH - 16 - UG-960028-12... -
Page 17: Jumpers And Switches
(OFF) S2-6 not connected (OFF) ON (closed) 1 (high) S2-7 (P00_1) OFF (open) 0 (low) ON (closed) 1 (high) S2-8 (P00_0) OFF (open) 0 (low) Table 4-1: MCU Operating Mode © Fujitsu Semiconductor Europe GmbH - 17 - UG-960028-12... - Page 18 Note: JP50 don‟t care, JP51A/B open Note: JP50, JP51A/B closed P00_1 16LX P00_0 1 2 3 4 5 6 7 8 Note: JP50, JP51A/B closed Figure 4-2: MCU mode switch: Flash Programming mode © Fujitsu Semiconductor Europe GmbH - 18 - UG-960028-12...
-
Page 19: P17_0 (Jp50)
Pin 17 disconnected from DIP Switch Open Open Open MB963xx: MD0) Table 4-3: Mode Pin DEBUG I/F (MD0) Settings Note: If one of both jumpers is closed, then the other one must not be closed either! © Fujitsu Semiconductor Europe GmbH - 19 - UG-960028-12... -
Page 20: Fkp (Jp54, Jp55)
P00_1 is disconnected from Flash-Kit Connector (X17) JP55 Closed P00_0 is connected to Flash-Kit Connector (X17) (P00_1) Open P00_0 is disconnected from Flash-Kit Connector (X17) Table 4-4: Flash Kit Program Port Pin P00_1 Settings © Fujitsu Semiconductor Europe GmbH - 20 - UG-960028-12... -
Page 21: Power Supply (Jp: 29, 30, 34, 40, 47)
Rule 4: By default, all Board supplies are set to 5V. Note: In case that the board is powered via the VG-connector (X4), a regulated 5 V power source has to be used and JP29 setting must be 2-3. © Fujitsu Semiconductor Europe GmbH - 21 - UG-960028-12... -
Page 22: Analogue Power Supply Voltage (Jp: 11, 13, 15)
(AVcc and AVss) to the A/D-converter. If JP13 is open, the resistors R11 and R23 define AVRH. By default the resistor network (R11 and R23) is not mounted on the board. © Fujitsu Semiconductor Europe GmbH - 22 - UG-960028-12... -
Page 23: Reset Generation (Jp: 4, 7, 24, 35)
DTR/RTS (JP3 and JP5) jumper have to be set, too (see chapter 4.10.2 or 4.11). If the reset LED is steadily on, check the power supply input voltage and the settings for the reset-generation by UART. © Fujitsu Semiconductor Europe GmbH - 23 - UG-960028-12... -
Page 24: Sub Clock (Jp: 36, 37)
Pin 20 is connected to the 32kHz sub clock (X1A) JP37 (X1A/P04_1) Pin 20 is used as P04_1 Table 4-8: Sub Clock Settings Rule 7: By default the 32 kHz sub-clock-crystal is connected to the microcontroller. © Fujitsu Semiconductor Europe GmbH - 24 - UG-960028-12... -
Page 25: Uart "A" / Lin "A" (Jp: 1, 2, 9, 10, 45)
No control signal as reset source selected Closed RTS and CTS of X3 are connected JP31 (RTS-CTS) Open RTS and CTS of X3 are not connected Table 4-10: UART "A" Settings © Fujitsu Semiconductor Europe GmbH - 25 - UG-960028-12... - Page 26 (LIN ”A” Vbat) LIN ”A” bus (X6 pin 1) is not powered by the board Open Table 4-11: LIN “B” Settings Note: Concerning pin assignment on the LIN DSUB-9 connector see chapter 5.4. © Fujitsu Semiconductor Europe GmbH - 26 - UG-960028-12...
-
Page 27: Uart"B" (Jp: 5, 6, 8, 32)
UART7_R means a relocation of the UART7 to other port pins. Additionally to the usual port pin configurations the relocated UART pins have to be activated in the peripheral resource relocation register 8 (PRRR8). PRRR8_SIN7_R :=1 PRRR8_SOT7_R :=1 © Fujitsu Semiconductor Europe GmbH - 27 - UG-960028-12... -
Page 28: Lin "B" (X6, Jp: 9, 10, 38, 39, 45)
UART8_R means a relocation of the UART8 to other port pins. Additionally to the usual port pin configurations the relocated UART pins have to be activated in the peripheral resource relocation register 8 (PRRR8). PRRR8_SIN8_R :=1 PRRR8_SOT8_R :=1 © Fujitsu Semiconductor Europe GmbH - 28 - UG-960028-12... -
Page 29: Can "A" (Jp: 25, 26)
There is no connection between MB90350 series and CAN “B”. Not all MB963xx microcontrollers have included the CAN-Interface. Please see datasheet for details. On the board there is no 120Ω termination for the CAN-bus. © Fujitsu Semiconductor Europe GmbH - 29 - UG-960028-12... -
Page 30: User Buttons Sw1, Sw2, Sw3, Sw4, Sw5 (Jp: 12, 14, 16, 20, 23)
Pin 51 (P07_0/IN1) of the MCU is connected to “SW5” Closed JP23 (SW5) Open No connection to the microcontroller Table 4-16: User Push Buttons Rule 8: By default all push-buttons are connected to the microcontroller. © Fujitsu Semiconductor Europe GmbH - 30 - UG-960028-12... -
Page 31: Connectors
TXD is the transmit output, RXD is the receive input. The DTR or RTS signal can be used to generate a reset. Please use 1:1 cable for PC-connection. CTS RTS DSR Connectors X3, X5 © Fujitsu Semiconductor Europe GmbH - 31 - UG-960028-12... -
Page 32: Lin"A", Lin"B" Interface Connector (X6, X8)
N1 can be removed. Instead of the user-LEDs one alphanumeric LC-Display (optional) can be connected. The following control-signals are reserved: VCC GND P06_7 P06_6 P06_5 P06_4 P06_3 P06_2 P06_1 P06_0 Port © Fujitsu Semiconductor Europe GmbH - 32 - UG-960028-12... -
Page 33: In-Circuit-Programming Connector (X17)
The MB96600 super series facilitates on-chip debugging via a single-wire system with the embedded emulator MB2100-01-E. The emulator is connected to the starter kit via SMA jack. Figure 5-2: Debug Connector © Fujitsu Semiconductor Europe GmbH - 33 - UG-960028-12... -
Page 34: Vcc 5 Volts (X18)
On this connector the VCC3V3 supply can be measured. 5.11 VCC Connector (X13) On this connector the VCC supply (see chapter 4.6) can be measured. 5.12 GND Connector (X14) Ground reference GND. © Fujitsu Semiconductor Europe GmbH - 34 - UG-960028-12... -
Page 35: Programming The Internal Flash Memory
Setting Description UART UART2 SIN2 is connected to RxD of X3 (SIN2) UART2 SOT2 is connected to TxD of X3 (SOT2) Table 6-2: Jumper Settings for Programming via UART “A” (X3) © Fujitsu Semiconductor Europe GmbH - 35 - UG-960028-12... - Page 36 UART8_R means a relocation of the UART8 to other port pins. Additionally to the usual port pin configurations the relocated UART pins have to be activated in the peripheral resource relocation register 8 (PRRR8). PRRR8_SIN8_R :=1 PRRR8_SOT8_R :=1 © Fujitsu Semiconductor Europe GmbH - 36 - UG-960028-12...
- Page 37 UART B (X5) is used to generate reset UART3 (MB96350) A/B) JP35 UART2 or No negation for the DTR/RTS signal UART7(MB96620) / (DTR / UART3 (MB96350) DTRx) DTR/RTS signal is negated Table 6-4: Jumper Settings for reset signal © Fujitsu Semiconductor Europe GmbH - 37 - UG-960028-12...
- Page 38 Rule 10: Use serial 1:1 cable for connection between PC and starter kit. 5. Connect the configured UART (see above) to your serial PC communication port. A straight 1:1 cable connection has to be used. 6. Power-on the board again. © Fujitsu Semiconductor Europe GmbH - 38 - UG-960028-12...
- Page 39 SK-96620_350-64PMC(1) User Guide Chapter 6 Programming the internal Flash Memory 7. Start the tool “Fujitsu Flash MCU Programmer” software and make the settings: Select your Device Type Select COM Port MB96F625 Select Crystal 4 MHz Open Source Application.MHX (MHX-File) Start programming 8.
-
Page 40: Synchronous Mode
In case that another Programming-Tool is used and the Mode-settings have to be done manually, then use the following configuration of DIP-switch S2 in order to select the synchronous-serial Flash-programming mode: © Fujitsu Semiconductor Europe GmbH - 40 - UG-960028-12... - Page 41 1 2 3 4 5 6 7 8 Mode Note: JP50 don‟t care, JP51A/B open Note: JP50, JP51A/B closed P00_1 16LX P00_0 1 2 3 4 5 6 7 8 Note: JP50, JP51A/B closed © Fujitsu Semiconductor Europe GmbH - 41 - UG-960028-12...
-
Page 42: Appendix
MB96F35xRS Flash MCU (Single Clock) with CAN MB96F35xRW Flash MCU (Dual Clock) with CAN MB96F35xAS Flash MCU (Single Clock) without CAN MB96F35xAW Flash MCU (Dual Clock) without CAN © Fujitsu Semiconductor Europe GmbH - 42 - UG-960028-12... -
Page 43: List Of Figures
Table 6-2: Jumper Settings for Programming via UART “A” (X3) ......... 35 Table 6-3: Jumper Settings for Programming via UART “B” ..........36 Table 6-4: Jumper Settings for reset signal ................37 © Fujitsu Semiconductor Europe GmbH - 43 - UG-960028-12... -
Page 44: Information In The Www
Microcontrollers (8-, 16- and 32-bit), Graphics Controllers Datasheets and Hardware Manuals, Support Tools (Hard- and Software) http://mcu.emea.fujitsu.com/ Power Management Products http://www.fujitsu.com/emea/services/microelectronics/powerman/ Media Products: SAW filters, acoustic resonators and VCOs http://www.fujitsu.com/emea/services/microelectronics/saw/ For more information about FUJITSU SEMICONDUCTOR http://www.fujitsu.com/emea/services/microelectronics/ © Fujitsu Semiconductor Europe GmbH - 44 - UG-960028-12... -
Page 45: Eu-Konformitätserklärung / Eu Declaration Of Conformity
9 EU-Konformitätserklärung / EU declaration of conformity Hiermit erklären wir, Fujitsu Semiconductor Europe GmbH, Pittlerstrasse 47, 63225 Langen, Germany dass dieses Board aufgrund seiner Konzipierung und Bauart sowie in den von uns in Verkehr gebrachten Ausführung(en) den grundlegenden Anforderungen der EU-Richtlinie 2004/108/EC „Elektromagnetische Verträglichkeit“... -
Page 46: China-Rohs Regulation
SK-96620_350-64PMC(1) User Guide Chapter 10 China-RoHS regulation 10 China-RoHS regulation This board is compliant with China RoHS. © Fujitsu Semiconductor Europe GmbH - 46 - UG-960028-12... -
Page 47: Recycling
According to the European WEEE-Directive and its implementation into national laws we take this device back. For disposal please send the device to the following address: Fujitsu Semiconductor Europe GmbH Warehouse/Disposal Monzastraße 4a 63225 Langen © Fujitsu Semiconductor Europe GmbH - 47 - UG-960028-12...