Related Manuals for Fujitsu SK-91464A-100PMC
Summary of Contents for Fujitsu SK-91464A-100PMC
-
Page 1: Evaluation Board
Fujitsu Microelectronics Europe FMEMCU-UG-910025-15 User Guide MB91460 SERIES EVALUATION BOARD SK-91464A-100PMC USER GUIDE... -
Page 2: Revision History
V1.2, MH smaller corrections jumper settings 2006/11/01 V1.2, MH correction FR-type 2006/11/27 V1.3, CSc, Socket Note added 2007/03/02 V1.4 Recycling Note added 2008/09/05 V1.5, MSc, China-RoHS regulation added This document contains 28 pages. FMEMCU-UG-910025-15 - 2 - © Fujitsu Microelectronics Europe GmbH... -
Page 3: Warranty And Disclaimer
Warranty and Disclaimer To the maximum extent permitted by applicable law, Fujitsu Microelectronics Europe GmbH restricts its warranties and its liability for the SK-91464A-100PMC Board and all its deliverables (eg. software include or header files, application examples, target boards, evaluation boards, engineering samples of IC’s etc.), its performance and any consequential damages, on the use of the Product in... -
Page 4: Table Of Contents
LIN”A”, LIN”B” Interface connector (X6, X8) ............21 CAN”A” Interface connector (X10)................. 21 USER-LEDs & optional LC-Display ............... 21 VG96 connector (X4)..................... 22 6 SILK-PLOT OF THE BOARD ..................23 7 RELATED PRODUCTS ....................24 FMEMCU-UG-910025-15 - 4 - © Fujitsu Microelectronics Europe GmbH... - Page 5 SK-91464A-100PMC User Guide Contents 8 INFORMATION IN THE WWW..................25 9 CHINA-ROHS REGULATION ..................26 10 RECYCLING ........................28 © Fujitsu Microelectronics Europe GmbH - 5 - FMEMCU-UG-910025-15...
-
Page 6: Overview
Chapter 1 Overview 1 Overview 1.1 Abstract The SK-91464A-100PMC is a multifunctional evaluation board for the Fujitsu 32-bit FR60 Flash microcontroller series MB91460. It can be used stand-alone for software development and testing or as a simple target board to work with the emulator system. -
Page 7: General Description
SK-91464A-100PMC User Guide Chapter 1 Overview 1.3 General Description The SK-91464A-100PMC supports the 32-bit Flash microcontroller MB91F464AA. It can be used as a stand-alone evaluation board or as a target board for the emulator debugger. The evaluation board supports the following package: FPT-100P-M20. -
Page 8: Installation
When turning on the system, be sure to use the following power-up sequence: 1. Power up the Emulator Main Unit (MB2198-01) 2. Power up the Adapter Board (MB2198-300) 3. Power up the target Board (SK-91464A-100PMC) To turn off the system, switch off the components in reverse order, beginning with the target Board. -
Page 9: Default Jumper Settings For Mb91464A
F 19 for usage with MB2198 Emulator System and Probe Cable MB91464A-NLS-100PMC both jumpers (JP29 and JP30) must either be set to position 1-2 or both must be set to position 2-3. © Fujitsu Microelectronics Europe GmbH - 9 - FMEMCU-UG-910025-15... - Page 10 SK-91464A-100PMC User Guide Chapter 2 Installation LIN“A“ LIN“B“ UART1 UART0 UART “A” CAN “A” UART3 CAN4 UART “B” UART4 FMEMCU-UG-910025-15 - 10 - © Fujitsu Microelectronics Europe GmbH...
-
Page 11: Jumpers And Switches
ON (closed) 1 (high) S2/2 (MD1) OFF (open) 0 (low) ON (closed) 1 (high) S2/3 (MD2) OFF (open) 0 (low) S2/4 not connected MD0 MD1 MD2 nc Dip-Switch S2 (default setting) © Fujitsu Microelectronics Europe GmbH - 11 - FMEMCU-UG-910025-15... -
Page 12: Power Supply (Jp: 29, 30, 37, 43, 44, 45)
(VBAT_A) Open No voltage supply to Vs of LIN A JP45 Closed Vs of LIN B is powered by the board (VBAT_B) Open No voltage supply to Vs of LIN B FMEMCU-UG-910025-15 - 12 - © Fujitsu Microelectronics Europe GmbH... -
Page 13: Analog Power Supply Voltage (Jp: 11, 13, 15)
If JP11 and JP15 are open, the user has to supply an adequate analog voltage supply (AVcc and AVss) to the A/D-converter. If JP13 is open, the resistors R11 and R23 define AVRH. By default the resistor network (R11, R23) is not mounted on the board. © Fujitsu Microelectronics Europe GmbH - 13 - FMEMCU-UG-910025-15... -
Page 14: Uart"A" (Jp: 1, 2, 31)
RTS and CTS of X5 are connected JP32 (RTS-CTS) Open RTS and CTS of X5 are not connected By default, UART4 is connected to UART”B”. UART “B” can be used for serial asynchronous Flash programming. FMEMCU-UG-910025-15 - 14 - © Fujitsu Microelectronics Europe GmbH... -
Page 15: Lin"A" (Jp: 17, 18, 21, 22, 44)
JP45 Closed Vs of LIN B is powered by the board (VBAT_B) Open No voltage supply to Vs of LIN B By default, the LIN”B”-interface is not connected to a UART. © Fujitsu Microelectronics Europe GmbH - 15 - FMEMCU-UG-910025-15... -
Page 16: Can"A" (Jp: 25, 26)
Reset is applied when SW6 is pressed >2sec Closed External Reset generation is active JP24 (Main Reset) Open No external Reset generation No negation for the DTR/RTS signal JP35 (Polarity) DTR/RTS signal is negated FMEMCU-UG-910025-15 - 16 - © Fujitsu Microelectronics Europe GmbH... -
Page 17: Buttons Sw1, Sw2, Sw3, Sw4, Sw5, Sw6 (Jp: 12, 14, 16, 20, 23, 24)
JP24 (Reset) Open No connection to INITX Default: JP12, JP14, JP16, JP20, JP23, JP24 = Closed By default, all push-buttons as well as the reset circuit are connected to the microcontroller. © Fujitsu Microelectronics Europe GmbH - 17 - FMEMCU-UG-910025-15... -
Page 18: Programming The Internal Flash
3. Start the Flash programmer by double-clicking on the flashprg.exe icon 4. Select appropriate MCU type, COM-Port, baudrate, and the path to your HEX-File (.mhx) 5. Power-off the board or assert and hold RESET FMEMCU-UG-910025-15 - 18 - © Fujitsu Microelectronics Europe GmbH... -
Page 19: Synchronous Mode
A dedicated Flash programming socket (X17) is provided on the evaluation-board for direct connection to this programmer. n/c 1 2 n/c MD0 3 4 MD2 RST 5 6 SIN4 X17: Flash programming socket SOT4 7 8 SCK4 VCC 9 10 GND © Fujitsu Microelectronics Europe GmbH - 19 - FMEMCU-UG-910025-15... -
Page 20: Connectors
TXD is the transmit output, RXD is the receive input. The DTR or RTS signal can be used to generate a reset. Please use a 1:1 cable for PC-connection. Connectors X3, X5: CTS RTS DSR FMEMCU-UG-910025-15 - 20 - © Fujitsu Microelectronics Europe GmbH... -
Page 21: Lin"A", Lin"B" Interface Connector (X6, X8)
(Port 27), the resistor network N1 can be removed. Instead of the user-LEDs an alphanumeric LC-Display (optional) can be connected. The following control signals are provided: VCC GND Port 27_7 27_6 27_5 27_4 27_3 27_2 27_1 27_0 © Fujitsu Microelectronics Europe GmbH - 21 - FMEMCU-UG-910025-15... -
Page 22: Vg96 Connector (X4)
Crystal 32kHz P22_5/SCL0 JP47 (Pullup 10k) Crystal 32kHz P19_0/SIN4 JP6 (UART B) 3A,B,C VSS5 P19_1/SOT4 JP8 (UART B) Crystal 4MHz P19_2/SCK4 Crystal 4MHz P17_0/PPG0 Pulldown 1k P17_1/PPG1 Pulldown 1k VDD5 3A,B,C VSS5 FMEMCU-UG-910025-15 - 22 - © Fujitsu Microelectronics Europe GmbH... -
Page 23: Silk-Plot Of The Board
Pin 99 Pin 1 4MHz Pin 100 Pin 2 91F464 Pin 50 Pin 52 Pin 49 Pin 51 FlashKit Power- MAX232 Jack MAX232 optional: LCD CAN”B” UART”B” Reset CAN”A” UART”A” LIN”A” LIN”B” © Fujitsu Microelectronics Europe GmbH - 23 - FMEMCU-UG-910025-15... -
Page 24: Related Products
Socket for package FPT-100P-M20 (Tokyo Eletech Corp. www.tetc.co.jp/e_tet.htm) < HQPack100SD Header for NQPACK100SD < MB91464A-NLS-100PMC Emulator probe cable for MB91F464A MCU < MB91460 Series < MB91V460 MB91460 Series Evaluation chip < MB91F464AAPMC Flash MCU FMEMCU-UG-910025-15 - 24 - © Fujitsu Microelectronics Europe GmbH... -
Page 25: Information In The Www
Datasheets and Hardware Manuals, Support Tools (Hard- and Software) http://www.fme.gsdc.de/gsdc.htm Linear Products: Power Management, A/D and D/A Converters http://www.fujitsu.com/emea/services/microelectronics/linears/ Media Products: SAW filters, acoustic resonators and VCOs http://www.fujitsu.com/emea/services/microelectronics/saw/ For more information about FUJITSU MICROELECTRONICS http://www.fujitsu.com/emea/services/microelectronics/ © Fujitsu Microelectronics Europe GmbH - 25 - FMEMCU-UG-910025-15... -
Page 26: China-Rohs Regulation
“Year”. FMEMCU-UG-910025-15 - 26 - © Fujitsu Microelectronics Europe GmbH... - Page 27 X: Indicates that this toxic or hazardous substance contained in at least one of the homogeneous materials used for this part is above the limit requirement in SJ/T11363-2006. • Data listed in the table represents best information available at the time of publication © Fujitsu Microelectronics Europe GmbH - 27 - FMEMCU-UG-910025-15...
-
Page 28: Recycling
According to the European WEEE-Directive and its implementation into national laws we take this device back. For disposal please send the device to the following address: Fujitsu Microelectronics Europe GmbH Warehouse/Disposal Monzastraße 4a 63225 Langen FMEMCU-UG-910025-15 - 28 - © Fujitsu Microelectronics Europe GmbH...