Table of Contents
Advertisement
Redialing
Both the base phone and the cordless handset can each individually
store five dialed phone numbers.
Turn
Press
(PROGRAM)
Notes
• When the Long Distance Saver function is set to "ACTIVE", "LONG
DISTANCE" call can be made (see page 19).
• The redial memory only registers up to 30 digits. Exceeding numbers will not
be redialed.
• In the case of a power failure, only the redial on the base phone will be
erased.
• The redial button does not store the access number of the Long Distance
Saver. To redial a long distance call, press (LONG DIST. SAVER), then
(REDIAL/PAUSE).
Tips
• When "p" is displayed on the right end of the phone number on the redial list
in step 2, it means that some number follows the displayed phone number.
Moreover, when the phone number is selected by turning Jog Dial, all of the
phone number is displayed in two lines.
• If you redial the same number repeatedly, this number will only be counted
as one number of the total five registered numbers that can be redialed.
• When dialing from a phone number with a registered name, that name will
be displayed in the list in step 2.
Receiving calls
(CALL WAITING/FLASH)
I (HEADSET)
jack
VOL switch
(HOLD)
(PROGRAM)
Receiving calls when the headset is connected
When a headset (optional) is connected to the I
(HEADSET) jack on the cordless handset, you can
talk through the headset.
1
Press (REDIAL/PAUSE).
2
Display the name or phone
number you want to call by
turning Jog Dial, and then press
Jog Dial. (If you're at the base
phone, press Jog Button
(ENTER).)
3
Turn Jog Dial to choose "DIAL"
or "LONG DISTANCE", and
then press Jog Dial (or Jog
Button (ENTER)).
The phone number will be
redialed.
continued
31
Basics
1
When you hear the phone ring:
• Press (TALK).
or
• Pick up the cordless handset
from the charger when the
cordless handset is placed on
the charger. (When Quick talk
is set to "USE"; see page 34)
"TALK" appears on the display
and the display also shows the
talk time in hours, minutes and
seconds.
"CORDLESS HANDSET IN
USE" appears on the display of
the base phone.
2
When you're done talking, press
(OFF) or replace the cordless
handset on the charger.
The display turns off.
Open
continued
33
Basics
Making calls (continued)
To store the dialed phone number into the Phone Directory
1
Display the name or phone number you want to store by
doing steps 1 and 2 on page 31.
2
Turn Jog Dial to choose "PROGRAM", and then press Jog
Dial. (If you're at the base phone, press Jog Button (ENTER).)
3
Enter the name by doing steps 4 and 5 on page 38.
4
Turn Jog Dial to choose "[PGM]", and then press Jog Dial (or
Jog Button (ENTER)).
You hear a long confirmation beep, and the name and the
number are stored.
Note
The dialed phone numbers of up to 20 digits can be stored in the Phone
Directory.
To erase the dialed phone number one by one
1
Display the name or phone number you want to erase by
doing steps 1 and 2 on page 31.
2
Turn Jog Dial to choose "ERASE REDIAL", and then press
Jog Dial. (If you're at the base phone, press Jog Button
(ENTER).)
3
Turn Jog Dial to choose "YES", and then press Jog Dial (or
Jog Button (ENTER)).
You hear a long confirmation beep, and the number is
erased.
To erase the entire dialed phone numbers at once
1
Press (PROGRAM).
2
Turn Jog Dial to choose "MEMORY MANAGE", and then
press Jog Dial. (If you're at the base phone, press Jog Button
(ENTER).)
3
Turn Jog Dial to choose "ERASE ALL RDL", and then press
Jog Dial (or Jog Button (ENTER)).
4
Turn Jog Dial to choose "ERASE REDIAL", and then press
Jog Dial (or Jog Button (ENTER)).
You hear a long confirmation beep, and the entire number
are erased.
US
32
US
Basics
Receiving calls (continued)
Additional tasks
To
Adjust the cordless handset
volume
Put a call on hold
Switch to another call
("call waiting" service*)
Receive a call by only picking
up the cordless handset from
the charger, without pressing
(TALK)(Quick talk)
* You need to subscribe to this service from your telephone company.
Note
If there is an incoming call during intercom conversation, intercom call will be
disconnected, and both the base phone and the cordless handset will ring.
Tip
To inform you of an incoming call, the display shows "** RINGING **" even
when you set the RING switch on the cordless handset to OFF.
If you have subscribed to the Caller ID service;
• the caller's number and/or name appears on the display when you receive a
call (see page 68) or when another call comes in by "call waiting" service.
• the name stored in the one-touch dialing or Phone Directory appears on the
display if the call matches the number stored on ONE-TOUCH DIAL buttons
or in the Phone Directory (memory match function; see page 68).
• the ringer sound changes to a higher tone if the call matches the number VIP
stored on ONE-TOUCH DIAL buttons or in the Phone Directory (memory
match function; see page 68).
To turn the ringer off
Set the RING switch on the bottom to OFF.
"[RINGER OFF]" appears on the display.
The cordless handset won't ring. You can still make
calls, and also receive calls if another telephone
connected to the same line rings to inform you on
incoming calls. You can also receive an intercom call.
US
US
34
Basics
– 10 –
Do this
Set the VOL switch to H (high), M (middle) or L
(low).
Press (HOLD). "HOLD" appears on the display.
Press (HOLD) again or pick up the cordless
handset from the charger (When Quick talk is
set to "USE"; see below) to resume the
conversation.
Press (CALL WAITING/FLASH).
Press (CALL WAITING/FLASH) again to return to
the first caller.
Press (PROGRAM). Turn Jog Dial to choose
"QUICK TALK", then press Jog Dial.
Turn Jog Dial to choose "USE", then press Jog
Dial.
RING switch
Advertisement
Table of Contents
