Group Settings And Interlock Settings Via The Me Remote Controller - Mitsubishi Electric PURY-P72 Service Handbook

[IV Remote Controller]
[2] Group Settings and Interlock Settings via the ME Remote Controller
1. Group settings/interlock settings
I ]
I.
[ )
(B) Interlock Settings
@Bring up the "Interlock Setting "window.
·Press button
@I
0'10000) to bring up the following display.
Press again to go back to the "Group Setting" window as shown
under step
® .
[Normal display) [Blinking display of "HO'1
(A) Group Settings
@Bring up the "Group Settlng"wlndow.
-Press and hold buttons
®
[FILTER) and @[.;-::::::..)
simultaneously for 2 seconds to bring up the display as
shown below.
Make the following settings to perform a group operation of units that are connected to different outdoor units or to manually set up the
indoor/outdoor unit address.
(A) Group setlings Registration of the indoor units to be controlled with the remote controller,
and search and deletion of registered information.
(B) Interlock settings Registralion of LOSSNAY units to be interlocked with the indoor units,
[Operation Procedures] and search and deletion of registered information
(1) Address settings
Register the indoor unit to be controlled with the remote controller.
<D
Bring up either the blinking display of "HO" by turning on the unit or the
normal display by pressing the ON/OFF button.
The display window must look like one of the two figures below to proceed to the
next step.
(VBring up the address of the Indoor unit and the address of the
LOSSNAY to
be
Interlocked on the display.
- select the address of the indoor unit to be registered by pressing
button© [TEMP. ('V) or (6)) to advance or go back through
the addresses.
- Select the address of the LOSSNAY unit
to
be interlocked by
pressing button@[TIMER SET (\7) or (6)) to advance or go back
through the " interlocked unit addresses:'
[' - ::-=-=-1-----:;----
I
--=--1.---",I] [ 1m
I
mi .
J " " L : : .
~
untt address display window
In~~ed
unit
~
addness address
@Select the unit address. display window display window
- Select the address of
the
indoor unit to be negistered
by pressing
button ©rrEMP. (\7) or (6)) to advance or go
back
through the addresses.
@Register the indoor unit whose address appears on the
display.
- Press button
@
[TEST] to register the indoor unit address
whose address appears on the display.
- If registration is successfully completed, unit type will appear
on the display as shown in the figure below.
- If the selected address does not have a conresponding indoor
unit, an error message will appear on the display. Check the
address, and try again.
I
] """..·..
00'""'.._ ...00
"interlocked unit address" will be
displayed together.
~
To search for an address,
"--V
go to section (2) "Address Search:'
<Successful completion of registration>
To next page.
If registration
is
successfully
completed, the
two
displays as
shown on the left will appear
alternately.
If the registration fails. "B8"
win blink on the display.
(Indicates that the selected
address does not have a
corresponding unit.)
®Make the settings to interlock LOSSNAY units with indoor
units.
- Press button @\TEST] while both the indoor unit address and
the address olthe LOSSNAY units to be interlocked
are displayed to enter the interlock setting.
-Interlock setting can also be made by bringing up the
LOSSNAY address in the indoor unit address display
window and the indoor unit address in the interlocked unit
address display window.
NOTE: Interlock all the indoor units in the group with the
LOSSNAY units; otherwise, the LOSSNAY units will
not operate.
I.
'C~
'L
l , -,r,,1
L'U
I
1
(Displayed alternately)
i
/
I
"I
LL
I n'n[
L./
IL.l . ,
::88
1
/1' 1
I.
Unit type (Indoo(unit In thIS case)
1
,-,
I
I
L.I
I
I "
I I
I
LI
I
I
To search for an address,
go to section (2) "Address Search:'
<Deletion error>
" 88" blinks to indicate a registralion error.
(Indicates that selecled address does not have a
corresponding unit.)
®To register the addresses for multiple Indoor units, repeat
steps @ and @ above.
HWE0803A
- 84-
GB