Sanyo VSP-8000 Instruction Manual page 22

MULTIPLEXER OPERATION
Command button operation list
The in the table tells you the corresponding section below for reference. Monitor 1 indicates the main monitor when a matrix
switching function is available.
VSP-8000 command button
MULTI
QUAD
PLUS
STILL
1
CAM/MPX *
SEQ
2
MON2/SPOT*
1
MON2/SPOT*
LIVE
VCR
FULL
NEXT
EXIT/BACK
MENU
Joystick lever
– , +
*1: When matrix switching function is available (main monitor and spot monitor terminals fitted)
•
If the multiplexer security lock is to be applied/released with the menu screen display, the controller operation will involve operating the
Note:
FULL button, numeric keypad and ENTER buttons.
•
If models with and without the matrix switcher function are connected at the same time in a group operation, the equipment will behave
differently when the MON2/SPOT button is operated.
•
The command display in the menu screen section will appear only on MON2.
Operations
A: Switches the channel of the monitor
1 plus screen
1.
Press the PLUS button.
Press the PLUS button again to cancel.
2.
Press the FULL button.
3.
Specify the channel with the numeric keypad.
Ex.: 4 → [4], 16 → [1] [6]
4.
Press the ENTER button.
B: Set sequential mode for monitor 1
plus screen
1.
Press the PLUS button.
Press the PLUS button again to cancel.
2.
Press the SEQ button.
C: Sets screen 1 to the specified
channel of monitor 2
1.
Press the MON2/SPOT button.
2.
Press the FULL button.
3.
Specify the channel with the numeric keypad.
4.
Press the ENTER button.
5.
Press the MON2/SPOT button again to
complete the setting.
D: Sequential display for monitor 2
screen
1.
Press the MON2/SPOT button.
2.
Press the SEQ button.
3.
Press the MON2/SPOT button again to
complete the setting.
Splits monitor 1 into multiple screens (16-screen/9-screen screen)
•
Splits monitor 1 into four screens
•
Switches the quad-screen
•
Displays the plus screen on the monitor 1
•
Switches channel of monitor 1 plus screen
•
Set sequential mode for monitor 1 plus screen
Still image screen of monitor 1
Switches Camera/Multiplexer operation.
Sequential display for selected monitor screen
•
Displays the specified channel on monitor 2
•
Switches the screen of monitor 2 automatically
•
Displays the specified channel on spot monitors 1 to 4
•
Switches spot monitor 1 to 4 screens automatically
•
Sets live video mode
•
The main monitor appears when connected in series
Sets video playback mode
Sets screen 1 to specified channel
Switches from menu screen to submenu
•
Returns display to previous menu.
•
2
Exits menu screen *
•
Brings up menu screen
•
1
Exits menu screen *
•
2
Switches menu screen *
Moves cursor (left, right, up, and down)
Changes selection settings
E: Sets full screen to specified channel
of spot monitor 1
1.
Press the MON2/SPOT button.
2.
Specify spot monitor 1 with the numeric
keypad.
Ex.: 1 → [1]
3.
Press the ENTER button.
4.
Press the FULL button.
5.
Specify the channel with the numeric
keypad.
6.
Press the ENTER button.
7.
Press the MON2/SPOT button again to
complete the setting for spot monitor 1.
F: Sequential display for spot monitor 1
1.
Press the MON2/SPOT button.
2.
Specify spot monitor 1 with the numeric
keypad.
Ex.: 1 → [1]
3.
Press the ENTER button.
4.
Press the SEQ button.
5.
Press the MON2/SPOT button again to
complete the setting for spot monitor 1.
Note: While spot monitor is selected, you must complete the selection of spot
monitors 1 to 4 or else other button operations will not be accepted until you
return to the main monitor by pressing the MON2/SPOT button twice.
Operation
*2: When matrix switching function is not available
21
Menu screen
MX:001 <MULTI>
MX:001 <QUAD>
MX:001 <PLUS>
( A)
( B)
MX:001 <STILL>
MX:001 <SEQ>
( C) MX:001 <MON2>
( D)
MX:001 <SPOT - >
( E)
( F)
MX:001 <LIVE>
MX:001 <VCR>
( G)
MX:001 <CH -- >
( H)
MX:001 <NEXT>
MX:001 <EXIT>
MX:001 <MENU>
MX:001 <LEFT>
MX:001 <RIGHT>
MX:001 <UP>
MX:001 <DOWN>
MX:001 <+>
MX:001 <->
G: Sets video playback mode
1.
Playback the video.
2.
Press the VCR button.
H: Sets screen 1 to the specified
channel
1.
Press the FULL button.
2.
Specify the channel with the numeric
keypad.
Ex.: 4 → [4]
M X : 0 0 1 < C H - >
-
3.
Press the ENTER button.
M X : 0 0 1 < C H 0 4 >