Sharp AR-FX12 Service Manual page 23

Main code 56
56-1
Purpose
Function (Content) Data transfer
Section
Item
Operation/Procedure Used to perform data transfer. Select an item
with 10 digit key pad and press START key.
The following operation is performed and the
display returns to the original state.
1. Data transfer executed
2. Data transfer not executed
SIMULATION 56-1
DATA COPY. SELECT 1 - 7, AND PRESS START.
1.ALL(EEPROM,SRAM,FlashROM)
2.HDD ALL(EEPROM,SRAM,FlashROM)
3.EEPROM HDD
4.HDD EEPROM
5.SRAM(+FAX Memory, +Option Memory)
6.HDD SRAM(+FAX Memory, +Option Memory)
7.FontROM HDD
press [START] key
SIMULATION 56-1
EEPROM HDD DATA COPY.
ARE YOU SURE?
1. YES
2. NO
<List of display values>
1* All memory contents are transferred to HDD.
(Same operation as 3.5.)
2* The contents of HDD are transferred to all memory.
(Same operation as 4.6.)
3 Transfer from EEPROM to HDD
4 Transfer from HDD to EEPROM
5* Transfer from SRAM to HDD.If, however, a FAX memory or an
option memory (for FAX) is installed, the contents of the FAX
memory are also transferred to HDD.
6* Transfer from HDD to SRAM. If, however, a FAX memory or an
option memory (for FAX) is installed, the contents of the FAX
memory are also transferred as well as the contents of HDD.
7 Transfer from Font Rom to HDD>
* : When the Flash ROM and the OP.Flash ROM are not installed,
transfer is not executed.
HDD
1
HDD
Press [CUSTOM SETTINGS] key
or [START] key
1
AR-FX12 SIMULATIONS, FAX SOFTWARE SWITCH 6-11
Main code 61
61-3
Purpose Adjustment
Function (Content) Used to adjust the scanner (exposure) laser
power (absolute value) in the FAX reception
mode. (Only when FAX is installed.)
Section PCU
Item Operation
Operation/Procedure Set the laser power in FAX operation.
Enter the set value and press START to store it.
Set range: 1 ~ 165
Default : (45PPM) 104
SIMULATION 61-3
LASER POWER SETTING (FAX). PRESS START.
1. FAX
5
Press [START] key.
SIMULATION 61-3
LASER POWER SETTING (FAX). INPUT VALUE 67-150, AND PRESS START.
1. FAX
<List of set values>
1 FAX reception
Main code 66
66-1
Purpose Setup
Function (Content) Used to set the FAX soft switch function.
(Used to utilize the FAX soft switch function.)
Section FAX
Item
Operation/Procedure Set the Fax soft switch.
(For details of the soft SW, refer to the AR-FX12
Specifications.)
SW1 cannot be changed with this simulation.
Entry of 1 - 8 only is effective.
1) Specify the bit to be changed (highlighted)
with a number.
2) Press START to rewrite the setting.
* SIM 1 cannot be changed with this simulation.
SIMULATION 66-1
FAX SOFT SW. SETTING. SELECT 2 - 120, AND PRESS START.
Press [START] key.
SIMULATION 66-1
FAX SOFT SW. SETTING. INPUT DATA No(1-8), AND PRESS START.
SOFT SW-2:
(35PPM) 88
1
Press [CUSTOM SETTINGS] key
or [START] key.
5
Initial value Set range
45PPM 104 1 ~ 165
35PPM 88
1
Press [CUSTOM SETTINGS] key
or [START] key.
1 2 3 4 5 6 7 8
00001001