Sharp AR-FX12 Service Manual page 70

B. Communication report codes
This code is indicated in the column of protocol communication report in a communication repot table and a communication management table when
communication is terminated.
<1>Communication report code XX (Top 2 digits): 00 ~ 99
<2>Communication report sub code 1: YY: Not used in this machine. (Always 00)
<3>Communication report sub code 2: ZZ: Indicates details of the report.
(1) Communication report code list 1
Means of communication: S = Send, R = Receive, P = Polling, B = Bulletin board
Report code
(Communication Display in the column of result
result)
0 ~ 31 Refer to the following
descriptions.
33 BUSY
34 CANCEL
35 NG35XXXX
36 (No record paper)
37 (Record paper jam)
38 MEM. FULL
39 (Number of paper unmatched)
40 (Relay not received)
41 LENGTH OVER
42 LENGTH OVER
43 (Communication) (OK)
44 ORIGINAL ERROR
45 (Picture quality error)
46 NO RESPONSE
47 TX DECODE ERROR
48 OK
OK REPLY RECEIVE
49 NO RX POLL
50 RX POLL FAIL
51 PASS # NG
52 (No confidential function in
remote party)
53 (Confidential not received)
54 (Confidential BOX NO NG)
55 (No relay function in remote
party)
56 NO REL RX
57 (Relay ID unmatched)
58 REJECTED
Communication report XX (YY ZZ)
Content of communication interruption
Depends on the point of communication interruption. For 16 or later, V.34 mode
communication. Refer to "(2) Communication report code list 2" in 7-6.
The calling side cannot establish connection with the remote party.
A communication interruption command is made during sending/receiving.The
interruption key is pressed for interruption of input.
Power is failed during sending/receiving.
Memory over during reception.Print is not made during reception in acting
reception inhibit.
The send data length of one page exceeds the limit (2m) in sending.
The receive data length of one page exceeds the limit.
Speaking before data transmission
A document jam occurs in direct sending.
The FAX signal from the remote party is not detected within T1 time.
A decode error occurs in the FAX board.
Normal end of communication
OK in internet FAX send with reception confirmation.
The called side does not have polling function in polling reception. The called side
has no data to send.
In polling reception, DCN is received for DTC.In polling sending, there is no send
data.
In poling sending, the allow number is not matched. In polling sending, the
system number is not matched.
In confidential sending, the remote party does not have confidential function.
(Including other company's machines)
<1>The NSF signal has not "Confidential function" bit.
<2>The NSF is not a Sharp machine.
<1>In confidential sending, DCN is received for NSS.
<1>In confidential reception, a confidential box number which is not registered is
specified.
In relay command sending, the remote machine has no relay function.
(Including other company's machine)
<1>The NSF signal has not "Confidential function" bit.
<2>The NSF is not a Sharp machine.
<1>In relay command sending, DCN is received for NSS.
<2>In relay command reception, a remote station number which is not registered
is specified.
<3>In F code relay broadcasting, an F code relay command is received.
<1>In relay command reception, the relay ID does not match.
In reception, data are sent from a remote machine of receive inhibit number.
AR-FX12 MACHINE OPERATION 7-6
Means of
communication
<S/R/P/B>
<S/R/P/B>
<R/P><R/P>
<S/B>
<R/P>
<S>
<S/P>
<S/B>
Normal end of
communication
<P><P>
<P><B>
<B><B>
<S>
<S>
<R>
<S>
<S><R><R>
<R>