Table of Contents
Advertisement
Warning Display
No Camera Signal
Camera signal is lost or distorted.
Please check the camera and cable
connection.
It can use as it is though a slight error
occurred.
System suspended due to unstable
processing. Recording will be resumed.
HDD
was disconnected.
System suspended due to unstable processing.
Start operation again.
The alteration part is found in the data.
Recorder detected technical problems
on the device.
The recorder has been rebooted. The problem
is not critical, but check the recorder.
Internal temperature is getting too high,
check the ventilation of the recorder.
Internal temperature is getting too high,
stop the operation of the recorder
immediately.
The fan of the recorder needs to be checked.
Copying data stopped because of new record
overwrites the old data.
New record will soon overwrite the old data
in copying.
Stop the recording, if you want to continue the
copying.
(NONE)
Regarding LOG14
#
deleted from the recording device. The recording is continued until all the registered HDDs are used up.)
#
Regarding LOG24
playback or copy again.
#
Regarding LOG 54
warning may not be displayed for the recording of which recording time is less than 2 seconds.
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••• Warnings and CALL OUT output
: Displays during recording. The system shuts down once and then resumes recording. (The error HDD is automatically
to 74
: Displays during copying or playback. The playback or copy stops because the system shuts down. Carry out
: Displays during recording when the video signal is not existed for the camera being recorded for 2 seconds or more. This
Countermeasure
• Check whether the unit
and camera are properly
connected and turned on.
• Check whether the video
signal is being properly
outputted.
• Check whether the camera
with no video signal input is
set for operation.
• Continue the operation
when there is no abnormality.
• When the error occurs
continuously, check the HDD/
media, cable, and termination,
and then restart the unit.
• Start operation again.
• Turn the power on again
using POWER button on the
front panel.
• Turn the power on again
using MAIN switch on the
rear panel.
• Check the unit.
• Turn off the power and
change the installation
condition.
• Turn off the power and
change the installation
condition.
• Turn off the power and
stop using.
• Stop HDD recording to
continue copy/backup.
• Stop HDD recording to
continue copy/backup.
• Stop copy/backup to
continue HDD recording.
• Restarts by watchdog
operation or for self-recovery.
CALL OUT
Cancelling
Log number
output
the warning
Stop recording.
LOG54
#7
Fixed
Output video
signals.
Click "Clear
Warning" or
press the E
button.
None
Automatically
LOG13
#8
clears after 1
LOG33
#8
minute.
LOG43
#8
LOG73
#8
LOG23
#8
Click "Clear
LOG14
#8
Fixed
Warning" or
press the E
button.
LOG74
#8
None
Automatically
LOG24
#8
clears after 1
LOG34
#8
minute.
LOG44
#8
Click "Clear
LOG55
#7
None
Warning" or
press the E
button.
Fixed
Click "Clear
LOG6200
Warning" or
press the E
button.
Click "Clear
Fixed
LOG5100
Warning" or
press the E
button.
Click "Clear
LOG5200
Fixed
Warning" or
press the E
button.
Fixed
Click "Clear
LOG5201
Warning" or
press the E
button.
Lower the
temperature.
Click "Clear
Fixed
LOG5300
Warning" or
press the E
button.
Rotate the fan.
Click "Clear
None
LOG3500#5
Warning" or
LOG7500#6
press the E
button.
None
Click "Clear
LOG3600#5
Warning or
LOG7600#6
press the E
button.
–
LOG5101
LOG5102
LOG5103
#1
35
Advertisement
Table of Contents
