Brother RH-9820 Service Manual page 107

1. Retaining ring C [4 pcs]
2. Ball bearings [4 pcs]
3. Retaining ring C [4 pcs]
4. Retaining ring C
5. Ball bearing
6. Retaining ring C
7. Y bearing
8. Y guide shaft
9. Set screws [2 pcs]
10. Clamp lever shaft
11. Clamp driving lever
12. Screw (Temporarily tighten)
13. Crank lever B
14. Socket bolt
15. Clamp lever shaft
16. Clamp driving lever
17. Screw (Temporarily tighten)
18. Crank lever B
19. Socket bolt
20. Cylinder rod
21. Auxiliary clamp
connecting rod
22. Retaining ring E
23. Cylinder rod pin
24. Retaining ring E
25. Joint [2 pcs]
26. Auxiliary clamp S holder
27. Retaining ring E
28. Pin
29. Retaining ring E
30. Cylinder
31. Screw
32. Washer
33. Retaining ring C
34. Spring hook
35. Clamp cylinder rod
36. Air bolster
37. Joint
38. Cylinder
39. Clamp cylinder support
40. Set screw
41. Retaining ring E
42. Cylinder rod pin
43. Retaining ring E
44. Spring
45. Spring hook
46. Clamp cylinder rod
47. Air bolster
48. Joint
49. Cylinder
＊1：Refer to "7-18. Adjusting the work clamp lift amounts".
＊2：Refer to "7-21. Adjusting the cloth opening amounts".
＊3：Refer to "7-20. Adjusting the positions of the work clamp plates".
50. Clamp cylinder support
51. Set screw
52. Retaining ring E
53. Cylinder rod pin
54. Retaining ring E
55. Spring
56. Cylinder screw
57. Joint [2 pcs]
58. Opening cylinder rod
59. Opening driving lever L
assembly
60. Retaining ring E
61. Cylinder rod pin B
62. Retaining ring E
63. Fulcrum lever plate
64. Slide block
65. Rocker lever
66. Washer
67. Retaining ring E
68. Cylinder
69. Retaining ring E
70. Shoulder screw [3 pcs]
71. Cylinder screw
72. Joints [2 pcs]
73. Opening cylinder rod
74. Opening driving lever R
assembly
75. Retaining ring E
76. Cylinder rod pin B
77. Retaining ring E
78. Fulcrum lever plate
79. Slide block
80. Rocker lever
81. Washer
82. Retaining ring E
83. Cylinder
84. Retaining ring E
85. Shoulder screw [3 pcs]
86. Speed nut
87. Screw (Temporarily tighten)
88. Stopper plate
89. Opening stopper plate
90. Washer
91. Screw (Temporarily tighten)
92. Speed nut
93. Screw (Temporarily tighten)
94. Stopper plate
95. Opening stopper plate
96. Washer
97. Screw (Temporarily tighten)
98. Spring
RH-9820
99. Nut (Temporarily tighten)
100. Bolt
101. Opening cylinder stopper
102. Spring washer
103. Screws [2 pcs]
104. Nut (Temporarily tighten)
105. Bolt
106. Opening cylinder stopper
107. Spring washer
108. Screws [2 pcs]
109. Plate guide B
110. Flat screws [3 pcs]
111. Plate guides A [5 pcs]
112. Flat screws [10 pcs]
113. Thread trimmer cylinder
support plate
114. Nut
115. Nut
116. Thread trimmer cylinder claw
117. Joint
118. Sensor
119. Cylinder
120. Socket bolts [2 pcs]
121. Collar
122. Retaining ring C
123. Gimp thread take-up guide
shaft
124. Set screw
125. Feed base plate spring
126. Screws [2 pcs]
Route the air tubes and harnesses
here. (Refer to pages 99 - 101.)
127. Feed base cover L
128. Flat screws [6 pcs]
129. Plate presser
130. Bending washer
131. Shoulder screw
132. Feed base cover R
133. Flat screws [6 pcs]
134. Plate presser
135. Bending washer
136. Shoulder screw
137. Feed base cover U
138. Truss screws [2 pcs]
6. ASSEMBLY
98