Table Of Contents - Toro LT-F3000 Operator's Manual

Contents
Safety ....................................................................... 4
General Safety................................................... 4
Safety and Instructional Decals .......................... 4
Setup ...................................................................... 10
Product Overview ................................................... 10
Controls ............................................................11
Specifications .................................................. 19
Attachments/Accessories ................................. 19
Before Operation ................................................. 20
Before Operation Safety ................................... 20
Performing Daily Maintenance.......................... 20
Filling the Fuel Tank .......................................... 20
During Operation ................................................. 21
During Operation Safety ................................... 21
Using the Operator Platform Latching
Mechanism ................................................... 22
Understanding the Operator Presence
Controls ........................................................ 22
Folding the Roll Bar .......................................... 23
Checking the Interlock Switches ....................... 24
Starting the Engine ........................................... 24
Shutting Off the Engine..................................... 25
Flail Cutting Unit General Information ............... 25
Adjusting the Height of Cut ............................... 25
Controlling the Position of the Individual
Cutting Units ................................................. 26
Using the Cutting Unit Auto-Limited Lift in
Reverse ........................................................ 26
Engaging the Cutting Unit Drive ........................ 27
Using Weight-Transfer/Traction
Assistance .................................................... 27
Operating Tips ................................................. 28
After Operation .................................................... 28
After Operation Safety ...................................... 28
Identifying the Tie-Down Points ........................ 29
Hauling the Machine ......................................... 29
Locating the Jacking Points .............................. 29
Towing the Machine .......................................... 29
Maintenance ........................................................... 32
Maintenance Safety.......................................... 32
Recommended Maintenance Schedule(s) ........... 33
Daily Maintenance Checklist............................. 35
Lubrication .......................................................... 36
Greasing the Bearings, Bushings, and
Pivots ............................................................ 36
Engine Maintenance ........................................... 36
Engine Safety ................................................... 36
Checking the Engine Overheat Warning
System.......................................................... 36
Servicing the Air Cleaner .................................. 37
Checking the Engine-Oil Level.......................... 38
Servicing the Engine Oil and Filter .................... 38
Fuel System Maintenance ................................... 39
Draining the Fuel Tank ...................................... 39
Checking the Fuel Lines and
Connections.................................................. 39
Bleeding the Fuel System ................................. 39
Replacing the Fuel Filter ................................... 40
Electrical System Maintenance ........................... 41
Electrical System Safety ................................... 41
Checking the Electrical System......................... 41
Checking the Battery Condition......................... 41
Servicing the Battery......................................... 41
Drive System Maintenance .................................. 42
Checking the Tire Pressure............................... 42
Checking the Torque of the Wheel-Lug
Nuts .............................................................. 42
Changing the Transmission Oil Filter ................ 42
Changing the Hydraulic-Return Filter ................ 42
Checking the Rear-Wheel Alignment ................ 43
Inspecting the Transmission Control Cable
and Operating Mechanism ............................ 43
Cooling System Maintenance .............................. 44
Cooling System Safety ..................................... 44
Removing Debris from the Cooling
System.......................................................... 44
Belt Maintenance ................................................ 45
Tensioning the Alternator Belt ........................... 45
Controls System Maintenance ............................. 46
Checking the Forward/Reverse Travel Pedal
Action............................................................ 46
Checking the Operator-Presence-Seat
Switch ........................................................... 46
Checking the Cutter-Drive-Interlock
Switch ........................................................... 46
Checking the Parking-Brake-Interlock
Switch ........................................................... 46
Checking the Transmission-Neutral-Interlock
Switch ........................................................... 46
Hydraulic System Maintenance ........................... 47
Hydraulic System Safety................................... 47
Checking the Hydraulic Lines and
Hoses............................................................ 47
Checking the Hydraulic Fluid ............................ 47
Servicing the Hydraulic System ........................ 48
Checking the Hydraulic-Fluid-Overheat
Warning System............................................ 48
Cutting Unit Maintenance ..................................... 49
Blade Safety ..................................................... 49
Replacing the Blades........................................ 49
Checking the Blade Bolts.................................. 49
Inspecting the Blades ....................................... 49
Checking the Rear Guard ................................. 50
Clearing a Blocked Rotor .................................. 50
Checking the Rubber Guard ............................. 51
Checking the Cutting Unit Pivot......................... 51
Checking the Rotor ........................................... 51
Checking the Rear-Roller Bearing
Adjustment.................................................... 51
Checking the Rear-Roller Scraper Wire
Tension ......................................................... 52
Cleaning .............................................................. 52
Washing the Machine ....................................... 52
Storage ................................................................... 53
3