Table of Contents
Advertisement
Quick Links
PowerCube 500 V200R001C10 Quick Guide
(AR550CX-300H1, AR550CX-300G1)
Issue: 05
Date: 2020-04-10
1
Overview
Appearance
Function module: AR550CX-
300H1, AR550CX-300G1
Lithium battery: CBM20E-N14A1
Function
Module
Color
Status
Meaning
Indicator
The function module has no power
Off
input or is faulty.
Blinking
The function module is communicating
Run
slowly
properly with upstream monitoring
Green
indicator
(0.5 Hz)
equipment.
The function module fails to
Blinking
communicate with upstream monitoring
fast (4 Hz)
equipment.
Off
There is no alarm.
Blinking
The function module has generated an
Alarm
slowly
alarm, which can be cleared.
Yellow
indicator
The function module has generated an
Steady
AC power failure or PV array fault alarm,
on
which can be cleared.
Off
The function module is normal.
Blinking
The function module has an external
Fault
Red
slowly
fault, which can be cleared.
indicator
Steady
The function module has an internal
on
fault, which cannot be cleared.
Grid Hybrid Scenario
Antenna
Lightning rod
CPE
Cantilever
Bullet
cameras
Pole
mounting kit
Lithium battery
Function
Lithium battery
module
Pole
Lithium
Battery
Indicator
Run
indicator
(RUN)
Alarm
indicator
(ALM)
The three indicators are steady on when the power unit of the
function module is upgrading. They return to normal status after the
upgrade is complete.
1
Copyright © Huawei Technologies Co., Ltd. 2020. All rights reserved.
Solar Hybrid Scenario
Lightning rod
Dome
camera
CPE
Pole
mounting kit
Pole
mounting kit
Function
module
Color Status
Meaning
The lithium battery has no power input or
Off
is faulty.
Steady on The lithium battery is powered on.
The lithium battery is communicating
Blinking
Green
slowly
properly with upstream monitoring
(0.5 Hz)
equipment.
Blinking
The lithium battery fails to communicate
fast (4 Hz)
with upstream monitoring equipment.
Off
There is no alarm.
The lithium battery has generated a fault
Steady on
alarm and needs to be replaced.
Red
Blinking
The lithium battery has generated a
slowly
protection alarm, which can be cleared.
(0.5 Hz)
NOTE
Antenna
PV modules
PV module
support
Cantilever
Dome camera
Bullet
cameras
Lithium battery
Lithium battery
Pole
Advertisement
Table of Contents
Related Manuals for Huawei PowerCube 500 V200R001C10
Summary of Contents for Huawei PowerCube 500 V200R001C10
- Page 1 PowerCube 500 V200R001C10 Quick Guide (AR550CX-300H1, AR550CX-300G1) Issue: 05 Date: 2020-04-10 Copyright © Huawei Technologies Co., Ltd. 2020. All rights reserved. Overview Appearance Grid Hybrid Scenario Solar Hybrid Scenario Function module: AR550CX- 300H1, AR550CX-300G1 Lightning rod Antenna Lightning rod Antenna...
- Page 2 Tools Routing Cables Through the Pole 1. Place the pole on a wooden case or a similar object. 2. Route a pull wire. 3. Route cables. Routing Cables Through CPE cable the Grid Hybrid Pole Mains AC cable, module ground cable, optical fiber, Mains AC cable Module camera cable, and CPE cable...
-
Page 3: Installing Cameras
Installing a Cantilever Installing Cameras and Cables Installing Cameras For the camera installation method, see the camera document. Installing Camera Cables For the cable connections at the camera side, see the camera document. Reserve the other ends of cables. (Optional) Installing the CPE For the CPE installation method, see the CPE document. - Page 4 6. Install horizontal beams. 7. Install two PV modules. Keep the slots of horizontal beams facing inwards for installing PV modules. Partially tighten the bolts so that PV modules can be adjusted during installation. Spacing shim Ensure that the junction boxes on the rear of PV modules are positioned consistently.
- Page 5 Installing a Lightning Rod Grid Hybrid Scenario Solar Hybrid Scenario Adjust the tilt angle of the lightning rod based on the site latitude. Site Lightning Rod Latitude Tilt Angle 0–15° 15° 16–25° 25° 26–30° 35° 31–45° 45° Installing an Antenna For the antenna installation method, see the antenna document.
- Page 6 4. Install a function module. 5. Install the lithium battery hanging kit. 3. Install the function module hanging kit. The option to install a lithium battery depends on the scenario. No lithium battery is required in the grid-only scenario. 7. (Optional) Install the second lithium battery. 6.
- Page 7 3. Drill holes and install bolts in the holes. 2. Mark mounting holes. One wall mounting kit A and one wall mounting kit B are used for each module. Determine the number of wall mounting kits based on the Hammer drill number of modules to be installed.
-
Page 8: Installing Cables
10.(Optional) Install the second 9. Install a lithium battery onto the wall. lithium battery onto the wall. If two lithium batteries are required, install them onto two adjacent wall hanging kits. Installing Cables Route inter-device cables through the pole. Installing Ground Cables for Modules 11.1 1. - Page 9 Installation Procedure 3. Install cables for PoE cameras. 1. Push up the sunshade 2. Open the maintenance until the spring fastener compartment door. is stuck gently. Cables for the dome camera can only be connected to the PoE++ 0–1 ports. Bullet camera 1 Dome camera Bullet camera 2...
- Page 10 9. Close the maintenance compartment door. 8. Install optical fibers. 10.Push down the sunshade until the spring Before closing the maintenance compartment fastener is stuck door, check that cables are properly installed. gently. After closing the door, press the left side of the maintenance compartment door by hand and tighten the screws.
- Page 11 Preparing AC Input Cables and Connecting Waterproof Connectors Flat-head Scale line screwdriver (Unit: mm) Installing Power Cables and Signal Cables 11.4 Ensure that caps and waterproof connectors are installed at all idle ports on the modules. Installing an RJ45 Communications Cable for a Lithium Battery Connecting Cables Between the Function Module and Lithium Batteries PV input AC input...
- Page 12 Installing Cable Covers 12.1 Installing a Cable Cover for the Function Module Install a Cable Cover for the Lithium Battery 12.2 Erecting the Pole Erecting the Mains Pole 2. Secure the pole to the foundation. 1. Check whether the pole needs to be repainted. Repaint the damaged area of the pole, and then use the crane to hoist the pole to the foundation.
-
Page 13: Verifying The Installation
Verifying the Installation 1. Check that the mounting kits are securely installed and all screws are tightened. 2. Check that all cables are reliably connected with correct polarity and there is no short circuit. 3. Check whether any screw holes are not installed with screws. If so, install screws at the holes. 4. -
Page 14: Basic Configuration
1. Run the system-view command to access the system view. 2. Run the sysname RouteA command to set the device name to RouteA. By default, the device host name is Huawei. 3. Run the vlan batch 22 1001 command to create the service VLAN and management VLAN. - Page 15 (The information displayed in the following figure is for reference only.) Run the display ip interface brief [ interface-type [ interface-number ] ] command to view the brief information about the IP address for the interface. Configuring Serial Port Transparent Transmission In the system view, run the following commands: 1.
- Page 16 Huawei Technologies Co., Ltd. Huawei Industrial Base, Bantian, Longgang Shenzhen 518129 People's Republic of China e.huawei.com...