Page 2
Descrizione Il dispositivo RD3P della famiglia dei relè differenziali elettronici RD3 di ABB svolge la funzione di monitor e protezione differenziale in accordo alla CEI EN 60947-2 annex. M* e può essere impiegato in abbinamento a tutti i dispositivi automatici S200 e scatolati della gamma Tmax fino al T5, per impianti industriali.
Page 4
Collegamento Toroide-Relè Remote Reset POWER SUPPLY RD3P: 230-400 VAC RD3P-48: 12-48 VAC/DC TR... FAULT l n [A] t [s] L O A D 0,06 0,03 RD3P Regolazione della corrente Pre Alarm TEST RESET Autoreset IEC60947-2/M d’intervento differenziale (l∆n [A]) Test no Trip (3s) e del tempo d’intervento (∆t [s]).
Page 5
Funzioni Pre-alarm → posizionando il dip-switch su ON si attiva la funzione di pre-alarm: il contatto di output contrassegnato dai morsetti 7 8 9 commuterà in caso di un guasto differenziale superiore al 60% I∆. Pre Alarm Autoreset OUTPUT Relay Prealarm / TRIP Autoreset →...
Page 6
Funzioni Fail-safe → integrata nel dispositivo (sicurezza positiva). In caso di mancanza dell’alimentazione del dispositivo RD3 i contatti di output numerati 10 11 12 commuteranno come da immagine allegata. FAIL SAFE OUTPUT Relay TRIP Contatti in condizione di dispositivo spento: BB_76x88mm_Rd3P_rev4.indd 6 19/09/11 11:04...
Page 7
Segnalazioni stand by TR... RD3P: 230-400 VAC RD3P-48: 12-48 VAC/DC RD... RD... FAULT BB_76x88mm_Rd3P_rev4.indd 7 19/09/11 11:04...
Page 10
Barra dei Led La barra dei Led visualizza l’entità della dispersione nell’impianto. RD3P 0,03 BB_76x88mm_Rd3P_rev4.indd 10 19/09/11 11:04...
Page 11
è collegato attraverso una bobina di sgancio. Collegamento con bobina a lancio di corrente: Remote Reset L O A D POWER SUPPLY RD3P: 230-400 VAC RD3P-48: 12-48 VAC/DC TR... FAULT l n [A] t [s] Bobina Lancio...
Page 12
Situazione di guasto Collegamento con bobina di minima tensione: Remote Reset L O A D POWER SUPPLY RD3P: 230-400 VAC RD3P-48: 12-48 VAC/DC TR... FAULT Bobina di l n [A] t [s] minima tensione 230V 0,06 0,03 RD3P Pre Alarm...
Page 13
Test TEST FAULT FAULT t [s] Remote RESET FAULT Reset FAULT Test NO TRIP TEST RESET FAULT FAULT 3 sec. uttore t [s] termico polare Remote RESET FAULT Reset FAULT BB_76x88mm_Rd3P_rev4.indd 13 19/09/11 11:04...
Caratteristiche tecniche Tensione di alimentazione RD3P 230-400 Vac +10% / -15% Tensione di alimentazione RD3P-48 12-48 Vac/Vdc +10% / -15% Frequenza di alimentazione RD3P / RD3P-48 50-60 Hz Filtraggio in frequenza Tipo A (fino a I ∆n = 5 A) Temperatura di funzionamento -25 °C ...
Page 15
Description The RD3P device is part of ABB’s RD3 family of residual current relays and provides residual current monitoring and protection in compliance with annex M to the CEI EN 60947-2 standard* and can be used in combination with all MCBs S200 and moulded-case devices in the Tmax range up to T5 for industrial plants.
Page 17
Toroid-Relay Connection Remote Reset POWER SUPPLY RD3P: 230-400 VAC RD3P-48: 12-48 VAC/DC TR... FAULT l n [A] t [s] L O A D 0,06 0,03 RD3P Regulation of operating current (l∆n [A]) Pre Alarm TEST RESET Autoreset IEC60947-2/M and trip time (∆t [s]).
Page 18
Functions Pre-alarm → by moving the dip-switch to ON the pre-alarm function is activated: the output contacts marked by terminals 7 8 9 will switch if a differential above 60% I∆ occurs. Pre Alarm Autoreset OUTPUT Relay Prealarm / TRIP Autoreset →...
Page 19
Functions Fail-safe → incorporated in the device (positive safety device) When no current is input to the RD3 device, the output contacts number 10 11 12 will switch as shown in the figure below. FAIL SAFE OUTPUT Relay TRIP Contact status when the device is switched off: BB_76x88mm_Rd3P_rev4.indd 19 19/09/11 11:04...
Connection with the shunt trip when the current is activated: Remote Reset L O A D POWER SUPPLY RD3P: 230-400 VAC RD3P-48: 12-48 VAC/DC RD3P TR... FAULT l n [A]...
Page 25
Fault status Connection to the undervoltage release Remote Reset L O A D POWER SUPPLY RD3P: 230-400 VAC RD3P-48: 12-48 VAC/DC TR... FAULT l n [A] t [s] Undervoltage release 0,06 0,03 RD3P Pre Alarm TEST RESET Autoreset IEC60947-2/M Test no Trip (3s) BB_76x88mm_Rd3P_rev4.indd 25...
Page 26
Test TEST FAULT FAULT t [s] Remote RESET FAULT Reset FAULT NO TRIP test TEST RESET FAULT FAULT 3 sec. t [s] Remote RESET FAULT Reset FAULT BB_76x88mm_Rd3P_rev4.indd 26 19/09/11 11:04...
Technical specifications RD3P power supply voltage 230-400 VAC +10% / -15% RD3P-48 power supply voltage 12-48 VAC/VDC +10% / -15% RD3P / RD3P-48 power supply frequency 50-60 Hz Frequency filtering Type A (up to I ∆n = 5 A) Operating temperature -25 °C ...
Page 28
Beschreibung Das Modell RD3P gehört zur Produktfamilie der von ABB entwickelten elektronischen Differenzstromrelais RD3 zum Fehlerstromschutz gemäß DIN EN 60947-2, Anhang M*; es kann in Kombination mit allen Leitungs-Schutzschaltern S200 und gekapselten Leistungsschaltern der Baureihe Tmax bis T5 für Industrieanlagen eingesetzt werden.
Page 30
Anschluss Wandler - Relais FERNRÜCKSETZUNG STROMVERSORGUNG RD3P: 230-400 VAC RD3P-48: 12-48 VAC/DC TR... FAULT l n [A] n [A] n [A] n [A] t [s] t [s] t [s] t [s] L A S T 0,06 0,06 0,03 0,03 RD3P RD3P Einstellung Empfindlichkeit (l∆n [A])
Page 31
Funktionen Voralarm → Wenn der DIP-Schalter auf ON steht, wird die Funktion Voralarm aktiviert: Der über die Klemmen 7, 8 und 9 gekennzeichnete Ausgangskontakt schaltet bei Präsenz von Fehlerströmen über 60% I∆. Pre Alarm Autoreset OUTPUT Relay Prealarm / TRIP Autoreset →...
Page 32
Funktionen Fail-Safe-Funktion → in Einheit eingebaut (positive Sicherheitseinrichtung). Bei Ausfall der Stromversorgung des RD3P schalten die Ausgangskontakte 10, 11 und 12 wie in der beiliegenden Abbildung gezeigt um. FAIL SAFE OUTPUT Relay TRIP Kontakte im ausgeschalteten Zustand des Geräts: BB_76x88mm_Rd3P_rev4.indd 32...
Page 36
LED-Leiste Die Led-Leiste zeigt den in der Anlage präsenten Ableitstrom in Prozent von I∆n an. STROM RD3P 0,03 BB_76x88mm_Rd3P_rev4.indd 36 19/09/11 11:04...
Page 37
Fehlersituation Liegt der vom Wandler ermittelte Fehlerstrom über dem Grenzwert I∆n, so bringt das Relais RD3P den über einen Arbeitsstromauslöser angeschlossenen Leistungsschalter zum Abschalten. Anschluss an Arbeitsstromauslöser:: FERNRÜCKSETZUNG L A S T STROMVERSORGUNG RD3P: 230-400 VAC RD3P-48: 12-48 VAC/DC TR...
Page 38
Fehlersituation Anschluss an Unterspannungsauslöser:: FERNRÜCKSETZUNG L A S T STROMVERSORGUNG RD3P: 230-400 VAC RD3P-48: 12-48 VAC/DC TR... FAULT l n [A] t [s] Unterspannungsauslöser 230V 0,06 0,03 RD3P Pre Alarm Vierpoliger TEST RESET Autoreset thermomagnetischer IEC60947-2/M Schutzschalter Test no Trip (3s) BB_76x88mm_Rd3P_rev4.indd 38...
Page 39
Test TEST FAULT FAULT t [s] Remote RESET FAULT Reset FAULT Test NO TRIP TEST RESET FAULT FAULT 3 sec. oliger t [s] gnetischer chalter Remote RESET FAULT Reset FAULT BB_76x88mm_Rd3P_rev4.indd 39 19/09/11 11:04...
Technische Kenndaten Versorgungsspannung RD3P 230-400 Vac +10% / -15% Versorgungsspannung RD3P-48 12-48 Vac/Vdc +10% / -15% Versorgungsfrequenz RD3P / RD3P-48 50-60 Hz Filtration in Frequenz A (bis I ∆n = 5 A) Betriebstemperatur -25 °C ... +70 °C Max. Leistungsaufnahme RD3P <3,6 W...
Page 41
Description Le dispositif RD3P de la famille des disjoncteurs directionnels électroniques RD3 de ABB fonctionne en tant qu'appareil de surveillance et protection différentielle conformément à la directive CEI EN 60947-2 annexe M* et peut être utilisé en association avec tous les dispositifs automatiques S200 et boîtiers de la gamme Tmax jusqu’à...
Page 43
Branchement Toron-Disjoncteur Remote Reset POWER SUPPLY RD3P: 230-400 VAC RD3P-48: 12-48 VAC/DC TR... FAULT l n [A] t [s] L O A D 0,06 0,03 RD3P Réglage du courant d’intervention Pre Alarm TEST RESET Autoreset IEC60947-2/M différentielle du disjoncteur (l∆n [A]) Test no Trip (3s) et du délai d’intervention (∆t [s]).
Page 44
Fonctions Préalarme → en positionnant le micro-interrupteur sur ON, la fonction de p réalarme s’active: le contact de sortie (output) indiqué par les bornes 7 8 9 commutera en cas de panne du différentiel supérieure à 60% I∆. Pre Alarm Autoreset OUTPUT Relay Prealarm / TRIP...
Page 45
Fonctions Sûreté → intégrée (ou Fail-safe) integrée dans le dispositif (sûreté positive). En cas de manque d’alimentation du dispositif RD3, les contacts de sortie numérotés 10 11 12 commuteront comme dans l’illustration ci-contre. FAIL SAFE OUTPUT Relay TRIP Contacts en situation de dispositif hors tension: BB_76x88mm_Rd3P_rev4.indd 45 19/09/11 11:04...
Page 46
Signalisations stand by TR... RD3P: 230-400 VAC RD3P-48: 12-48 VAC/DC RD... RD... FAULT BB_76x88mm_Rd3P_rev4.indd 46 19/09/11 11:04...
Page 49
Barre des Diodes La barre des Diodes visualise l’entité de la dispersion dans l’installation. BB_76x88mm_Rd3P_rev4.indd 49 19/09/11 11:04...
Page 50
I∆n, le disjoncteur RD3 provoque l’ouverture de l’interrupteur automatique auquel il est branché via une bobine de déclenchement. Branchement avec bobine à lancement de courant: Remote Reset L O A D POWER SUPPLY RD3P: 230-400 VAC RD3P-48: 12-48 VAC/DC RD3P TR... FAULT l n [A] t [s] Bobine à...
Page 51
Situation de panne Branchement avec bobine de tension mini: Remote Reset L O A D POWER SUPPLY RD3P: 230-400 VAC RD3P-48: 12-48 VAC/DC TR... FAULT Bobine de l n [A] t [s] tension mini 230V 0,06 0,03 RD3P Pre Alarm...
Page 52
Test TEST FAULT FAULT t [s] Remote RESET FAULT Reset FAULT Test NO TRIP TEST RESET FAULT FAULT 3 sec. t [s] Remote RESET FAULT Reset FAULT BB_76x88mm_Rd3P_rev4.indd 52 19/09/11 11:04...
Caractéristiques techniques Tension d’alimentation RD3P 230-400 Vac +10% / -15% Tension d’alimentation RD3P-48 12-48 Vac/Vdc +10% / -15% Fréquence d’alimentation RD3P / RD3P-48 50-60 Hz Filtrage en fréquence Type A (jusqu’à I ∆n = 5 A) Température de fonctionnement -25 °C ... +70 °C Puissance max.
Page 54
Descripción El dispositivo RD3P de la familia de los relés diferenciales electrónicos RD3 de ABB realiza la función de monitor y protección diferencial según IEC EN 60947-2 anexo M* y puede utilizarse con todos los interruptores automáticos S200 y caja moldeada de la gama Tmax hasta el T5, para instalaciones industriales.
Page 56
Conexión Toroide-Relé Remote Reset POWER SUPPLY RD3P: 230-400 VAC RD3P-48: 12-48 VAC/DC TR... FAULT l n [A] t [s] L O A D 0,06 0,03 RD3P Regulación de la corriente de Pre Alarm TEST RESET Autoreset IEC60947-2/M intervención diferencial (l∆n [A]) Test no Trip (3s) y del tiempo de intervención (∆t [s]).
Page 57
Funciones Prealarma → poniendo el conmutador DIP en ON se activa la función de prealarma: el contacto de salida marcado por los bornes 7, 8 y 9 conmutará en caso de que se produzca una avería diferencial superior al 60% I∆. Pre Alarm Autoreset OUTPUT Relay...
Page 58
Funciones Fail-safe → integrada en el dispositivo (seguridad positiva). En caso de ausencia de ausencia de alimentación del dispositivo RD3 los contactos de salida 10, 11 y 12 conmutarán como en la imagen anexa. FAIL SAFE OUTPUT Relay TRIP Contactos con dispositivo apagado: BB_76x88mm_Rd3P_rev4.indd 58 19/09/11 11:04...
Page 62
Barra de Leds La barra de Leds visualiza la magnitud de la dispersión en la instalación. RD3P 0,03 BB_76x88mm_Rd3P_rev4.indd 62 19/09/11 11:04...
Page 63
I∆n, el relé RD3 provoca la apertura del interruptor automático al que está conectado a través de emissión de corriente. Conexión con bobina de emisión de corriente: Remote Reset L O A D POWER SUPPLY RD3P: 230-400 VAC RD3P-48: 12-48 VAC/DC TR... FAULT l n [A] t [s]...
Page 64
Situación de avería Conexión con bobina de mínima tensión: Remote Reset L O A D POWER SUPPLY RD3P: 230-400 VAC RD3P-48: 12-48 VAC/DC TR... FAULT Bobina de l n [A] t [s] mínima tensión 230V 0,06 0,03 RD3P Pre Alarm...
Page 65
Test TEST FAULT FAULT t [s] Remote RESET FAULT Reset FAULT Test NO TRIP TEST RESET FAULT FAULT 3 sec. uptor t [s] térmico polar uptor otérmico polar Remote RESET FAULT Reset FAULT BB_76x88mm_Rd3P_rev4.indd 65 19/09/11 11:04...
Características técnicas Tensión de alimentación RD3P 230-400 Vac +10% / -15% Tensión de alimentación RD3P-48 12-48 Vac/Vdc +10% / -15% Frecuencia de alimentación RD3P / RD3P-48 50-60 Hz Filtrado en frecuencia Tipo A (hasta I ∆n = 5 A) Temperatura de funcionamiento -25°C ...