Remote Programming Guides - Panasonic EYFLA4 Quick Manual

Number
Button Setting Mode
of Push
0 Torque setting
A
Flush Detection Mode
1 time
Setting
B
1 times Rehit Prevention
1 time Restore Factory Defaults
C
2 times Out Of Range/Anti-Theft
D
1 time Tool Model Number
Number
Button Setting Mode
of Push
0 Torque setting
Flush (Snug torque)
1 time
A
detection mode setting
2 times Buzzer setting
1 Times LED Light
B
2 times Rundown error detecting
3 times Variable speed control
1 time Restore Factory Default
2 times Maintenance interval alarm
C
Out of range disable
3 times
function
D
1 time Cross thread reduction
Mechanical Pulse
EYFLA4 | EYFLA5 | EYFLA6 | EYFMA1
Quick Programming guide
Tool display
1~30: Shut-off
F: Non shut-off
L1: Stage 1
L2: Stage 2
0～30 = OFF
1～3.0 = .1 tp 3.0 sec
F
C0: OFF
C1: ON
Model Number
EYFNA1 | EYFPA1
Quick Programming guide
Tool display
1~30: Shut-off
F: Non shut-off
L1: Stage 1
L2: Stage 2
b0: No buzzer
b1: Buzzer with OK
b2: Buzzer with NOK
d1: by LED button (for
d2: by trigger switch
0～30 = Off
1～3.0 = .1 to 3.0 sec
P0: Variable speed (ON)
P1: Single speed (OFF)
F
0～99 = Off
1-99 = 10,000-990,000
Run Downs
C0: OFF
C1: ON
R0: OFF
R1: 360°reverce (ON)
Panasonic Life Solutions Company of America Assembly Tools Division
2 Riverfront Plaza 5
www.panasonic.com/assemblytools
Description
Select stage with ＋/－button. Initial setting is 「F」
Select stage with ＋/－button. Initial setting is 「L1」
L1: For applications with no pulses before the flush point (fragile material)
L2: For applications when the tool pulses before achieving flush point
Select stage with ＋/－button. Initial setting is 「0」
All settings return to initial setting. On "F" press "Save" (Blue Button)
Select stage with ＋/－button. Initial setting is 「C0」
In the event that wireless communication cannot be completed between the tool and the
qualifier, the tool will be disabled and cannot be operated.
Will display model number
Description
Select stage with ＋/－button. Initial setting is 「F」
Select stage with ＋/－button. Initial setting is 「L1」
L1: For applications with no pulses before the flush point (fragile material)
L2: For applications when the tool pulses before achieving flush point
Select stage with ＋/－button. Initial setting is 「b0」
Select stage with +/- button. Initial setting is 「d1」
Select stage with ＋/－button. Initial setting is 「0」
If the clutch is activated before the programmable minimum runtime,
the tool alerts the operator to a NOK fastening. (0.1sec. per stage)
Select stage with ＋/－button. Initial setting is 「P0」
Speed can be controlled by use of the trigger.
All settings return to initial setting. On "F" press the "Save" (Blue Button)
Select stage with ＋/－button. Initial setting is 「0」
When total fastening times are within 1 hour of preset maintenance interval, tool's display blinks
notifying the operator.
Once tool reaches the preset interval, the tool is looked out from further use.
Select stage with ＋/－button. Initial setting is 「C0」
In the event that wireless communication cannot be completed between the tool and the
qualifier, the tool will be disabled and cannot be operated.
Select stage with ＋/－button. Initial setting is「R0」
Tool first reverses 360 degree, aligning the threads, greatly reducing the possibility of cross
threads.
th
Floor Newark, NJ 07102