Table of Contents
Advertisement
Conduc
ted RF
IEC
61000-4-
6
Radiated
RF
IEC
61000-4-
3
NOTE 1 At 80 MHz and 800 MHz, the higher fre
quency range applies.
NOTE 2 These guidelines may not apply in all situa
tions. Electromagnetic propagation is affected by
absorption and reflection from structures, objects
and people.
(a) Field strengths from fixed transmitters, such as
base stations for radio (cellular/cordless) telepho
nes and land mobile radios, amateur radio, AM and
FM radio broadcast and TV broadcast cannot be
predicted theoretically with accuracy. To assess
the electromagnetic environment due to fixed RF
transmitters, an electromagnetic site survey should
be considered. If the measured field strength in the
location in which the device is used exceeds the
applicable RF compliance level above, the device
should be observed to verify normal operation. If
abnormal performance is observed, additional mea
sures may be necessary, such as re-orienting or
relocating the device.
(b) Over the frequency range 150 kHz to 80 MHz,
field strengths should be less than 3V/m.
Recommended separation distances
between portable and mobile RF com
munications equipment and the ME
equipment or ME system – for ME
equipment and ME systems that are
not life supporting
Recommended separation distances between por
table and mobile RF communications equipment
and the device.
The device is intended for use in an electromagne
tic environment in which radiated RF disturbances
are controlled. The customer or the user of the devi
ce can help prevent electromagnetic interference
by maintaining a minimum distance between porta
ble and mobile RF communications equipment
(transmittters) and the device as recommended
below, according to the maximum output power of
the communications equipment.
Rated
maximum
output
power of
transmitter
(W)
0.01
0.1
1
10
100
For transmitters rated at a maximum output power
not listed above, the recommended separation dis
tance d in metres (m) can be estimated using the
equation applicable to the frequency of the trans
mitter, where P is the maximum output power
rating of the transmitter in watts (W) according to
the transmitter manufacturer.
NOTE 1 At 80MHz and 800MHz, the separation dis
tance for the higher frequency range applies.
NOTE 2 These guidelines may not apply in all situa
tions. Electromagnetic propagation is affected by
absorption and reflection from structures, objects
and people.
Français
Introduction
Félicitations pour votre achat et bienvenue dans
l'univers Philips ! Pour profiter pleinement de l'as
sistance offerte par Philips, enregistrez votre pro
duit à l'adresse suivante : www.philips.com/wel
come.
3
3
Vrms
Vrms
150
kHz
to
80
MHz
3
3
V/m
V/m
80
MHz
to
2.5
GHz
Separation distance according to
frequency of transmitter (m)
150 kHz to
80 MHz
Ö
d = 1.167
P
0.117
0.369
1.167
3.690
11.67
Portable and mobile
RF communications
equipment should be
used no closer to any
part of the device,
including cables, than
the recommended
separation distance cal
culated from the equa
tion applicable to the
frequency of the trans
mitter.
Recommended separa
tion distance:
ÖP
d = 1.167
ÖP
d = 1.167
2.5 GHz
ÖP
d = 2.333
to 2.5 GHz
P
where
is the maxi
mum output power
rating of the transmit
ter in watts (W) accor
ding to the transmitter
manufacturer and
the recommended
separation distance in
metres (m).
Field strengths from
fixed RF transmitters,
as determined by an
electromagnetic site
survey (a), should be
less than the complian
ce level in each fre
quency range (b).
Interference may occur
in the vicinity of equip
ment marked with the
following symbol:
80 MHz
800 MHz
to 800
to 2.5 GHz
MHz
d = 1.167
Ö
d = 1.167
P
P
0.117
0.233
0.369
0.738
1.167
2.333
3.690
7.378
11.67
23.33
80 MHz to
800 MHz
d
is
Ö
Advertisement
Table of Contents
