Table of Contents
Advertisement
9-6 Setting contents of slave station parameters
When the JW-20CM is used as a slave station, set the following items for parameters.
Setting item
Setting time-out item of SEND/
①
RECEIVE instruction
Setting PC model of each
②
station in SEND/RECEIVE
function
Select system of each channel
in SEND/RECEIVE function
※1
③
Top addresses in communi-
cation information storage area
④
when using data memory start-
ing system of SEND/RECEIVE
functions
Number of receiving bytes of
relay link in memory capacity
⑤
save function
Number of receiving bytes of
register link in memory
⑥
capacity save function
※2
Top address of relay link
area
⑦
Top address of register link
area
⑧
9
Whether the station number
⑨
information should be output
or not
Top address of flag area
(communication and PC
⑩
operation condition monitor
flag)
⑪
Communication error
detection interval
Writing to the EEPROM,
⑫
start operation/stop setting
※ 1 Set only any of JW50/70/100 or JW50/70H/100H is used as PC, and using SEND/RECEIVE
instruction.
※2 Set only any of JW50/70/100 or JW50/70H/100H is used as PC, and using the memory capacity
save function.
① to ⑫ correspond to numbers in the next page.
Initial
Address
)
(8
value
(H)
007500
For using SEND/RECEIVE instruction, set the
00
to
time out time by decimal.
007577
[001 (0.1 sec..) to 255 (25.5 sec.)]
91
007600
(H)
91
to
81
(H)
007677
00/81
007700
Select instruction system or data memory starting
00
to
system in CH0 to CH3
V5
007703
Setting by file number and file address.
007710
· Setting within communication information
storage area (64 bytes)
to
00
File 0: 000000 to 015777
007713
File 1 to 7: 000000 to 177777
V5
Set the number of bytes by decimals. (0 to 64)
· If 0 is set, the number of bytes will be the same
007720
00
as the number of the sending bytes which is set
007721
V5
in the master station
Set the number of bytes by decimals. (0 to 512)
· If 0 is set, the number of bytes will be the same
007722
00
as the number of the sending bytes which is set
007723
V5
in the master station
Set by file number and file address.
007730
(See page 13·20 and 13·21)
00
to
V5
007733
007734
Set by file number and file address.
00
(See page 13·20 and 13·21)
to
007737
V5
Store the number of own station in the data memory
00
007763
when setting on 01
V2
flag area of 24 bytes, valid when 007767
E0
007764
Lower of file address
01
007765
Upper of file address
00
007766
File number
80
007767
Flag output (Yes: 80
00
007771
Settable detection interval with 100 ms pitch
00
(H)
01
(H)
01
007777
80
(H)
81
(H)
08
(H)
9
22
·
Contents
: The PC is JW type and ZW-20CM has
JW mark or JW-20CM or JW-22CM
: The PC is ZW type and ZW-20CM
has JW mark or JW-20CM.
:ZW-20CM without JW mark
(H)
(8)
(8)
.
(storage area of 1 byte follows
(H)
Initial value: 01E0
007767
(8)
No: 00
)
(H)
(H)
: Stop remote I/O operation
: Start remote I/O operation
: Writing to the EEPROM, stop operation
: Writing to the EEPROM, start operation
: Initialize the parameter
Corresponding
signs on pages
11·7 and 11·8
h
h
n
to
1
i
i
n
to
1
f
f
n
to
1
g
g
n
to
1
is 80
)
(8)
(H)
(H)
↓
(ｺ0740)
e
e
n
to
1
Advertisement
Table of Contents
