Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for ABB RETA-01
Summary of Contents for ABB RETA-01
- Page 1 ABB Drives User’s Manual Ethernet Adapter Module RETA-01...
- Page 3 Ethernet Adapter Module RETA-01 User’s Manual 3AFE64539736 Rev D EFFECTIVE: 23.3.2007 © 2007 ABB Oy. All Rights Reserved.
-
Page 5: Safety Instructions
Safety instructions Overview This chapter states the general safety instructions that must be followed when installing and operating the RETA-01 Ethernet Adapter module. The material in this chapter must be studied before attempting any work on, or with, the unit. - Page 6 Safety instructions...
-
Page 7: Table Of Contents
EtherNet/IP ..........15 The RETA-01 Ethernet Adapter module ......16 Compatibility . - Page 8 RETA-01 configuration ........
- Page 9 RETA-01 ........
- Page 10 Table of Contents...
-
Page 11: Introduction
Safety instructions are featured in the first few pages of this manual. Overview contains a short description of the Ethernet protocols and the RETA-01 Ethernet Adapter module, a delivery checklist, and information on the manufacturer’s warranty. Quick start-up guide contains a short description of how to set up the RETA-01 Ethernet Adapter module. -
Page 12: Terms Used In This Manual
Network configuration explains the different methods of setting up the network configuration. Communication profiles describes AC/DC Drive profile and ABB Drives profile Communication contains a description of how data is transmitted through the RETA-01 module. - Page 13 RETA-01 Ethernet Adapter module The RETA-01 Ethernet Adapter module is one of the optional fieldbus adapter modules available for ABB drives. The RETA-01 is a device through which a drive is connected to an Ethernet network.
-
Page 14: Product And Service Inquiries
Product and service inquiries Address any inquiries about the product to your local ABB representative, quoting the type code and serial number of the unit in question. A listing of ABB sales, support and service contacts can be found by navigating to www.abb.com/drives and selecting Drives –... -
Page 15: Overview
The supported Modbus commands are listed in chapter Communication. The Modbus/TCP protocol allows the RETA-01 module to be used as an Ethernet bridge to control the drive. The RETA-01 module supports eight simultaneous IP connections. Further information can be obtained from www.modbus.org. -
Page 16: The Reta-01 Ethernet Adapter Module
The RETA-01 Ethernet Adapter module The RETA-01 Ethernet Adapter module is an optional device for ABB drives which enables the connection of the drive to a Ethernet network. The drive is considered as a slave on the Ethernet network. Through the RETA-01 Ethernet Adapter module, it is possible to: •... -
Page 17: Compatibility
NETWORK STATUS Top view Side view Figure 1. The RETA-01 Adapter module. Compatibility The RETA-01 is compatible with all master stations that support the Modbus/TCP and/or EtherNet/IP protocols. Delivery check The option package for the RETA-01 Ethernet Adapter module contains: •... -
Page 18: Warranty And Liability Information
(12) months after installation or twenty-four (24) months from date of manufacturing, whichever first occurs. The local ABB office or distributor may grant a warranty period different to the above and refer to local terms of liability as defined in the supply contract. -
Page 19: Quick Start-Up Guide
(printed on a sticker on the back of the module). • Make sure you have the two screws for fastening the module. Mechanical installation • Insert the RETA-01 into its specified slot in the drive (SLOT2 for ACS550, SLOT1 for ACS800). • Fasten the two screws. - Page 20 • One way of setting the IP address is to use the ARP (Address Resolution Protocol) command from a PC. The new IP address will be stored in the RETA-01 configuration parameters. An example of how to change the IP address from the DOS Prompt window is shown below.