Replaceable; Introduction; Ordering Information - HP 211B Operating And Service Manual

Section VI
SECTION VI
REPLACEABLE PARTS
6-1 INTRODUCTION
a) Description of the part (see list of abbreviations below)
b) Typical manufacturer of the part in a five-digit code;
see list of manufacturers in appendix.
c) Manufacturer's stock number.
d) Total quantity used in the instrument (TQ column).
e) Recommended spare part quantity for complete main-
tenance (RS column) during one year of isolated service.
6-3 Miscellaneous parts not indexed in table 6-1 are listed
at the end of table 6-2.
6-4 ORDERING INFORMATION
6-5 To order a replacement part, address order of inquiry
either to your authorized Hewlett-Packard sales represen-
tative or to
CUSTOMER SERVICE
Hewlett-Packard Company
395 Page Mill Road
Palo Alto, California
or, in Western Europe, to
Hewlett-Packard S.A.
54 Route des Acacias
Geneva, Switzerland
6-6 Specify the following information for each part:
a) Model and complete serial number of instrument.
b) Hewlett-Packard stock number.
c) Circuit reference designator.
d) Description
6-7 To order a part not listed in tables 6-1 and 6-2, give a
complete description of the part and include its function
and location.
REFERENCE DESIGNATORS
A = assembly F = fuse P = plug Vv = vacuum tube, neon
B = motor FL = filter Q = transistor bulb, photocell, etc.
c = capacitor J = jack R = resistor WwW = cable
CR = diode K = relay RT = thermistor x = socket
DL = delay line L = inductor s = switch Y = crystal
DS = device signaling (lamp) M = meter T = transformer Z = network
E = mise electronic part MP = mechanical part
ABBREVIATIONS
A = amperes F = farads NC = normally closed S-B = slow-blow
BP = bandpass FXD = fixed NE = neon SE = selenium
BWO = backward wave NO = normally open SECT = section(s)
oscillator GE = germanium NPO = negative positive zero SI = silicon
GL = glass (zero temperature SIL = silver
CER = ceramic GRD = ground(ed) coefficient) SL = slide
CMO = cabinet mount only SPL = special
COEF = coefficient H = henries NSR = not separately
COM = common HG = mercury replaceable TA = tantalum
COMP = composition HR = hour(s) TD = time delay
CONN = connection TI = titantium dioxide
CRT = cathode-ray tube IMPG = impregnated OBD = order by description TOG = toggle
INCD = incandescent Ox = oxide TOL = tolerance
DEPC = deposited carbon INS = insulation(ed) TRIM = trimmer
TWT = traveling wave tube
EIA == Tubes or transistors K = kilo = 1000 P = peak
meeting Electronic PC = printed circuit board U = micro =10-6
Industries' Associa- LIN = linear taper PF = picofarads = VAC = vacuum
tion standards will LOG' = logarithmic taper 10-12 farads VAR = variable
normally result in PP = peak-to-peak wi = with
instrument operating PIV = peak inverse voltage w = watts
within specifications; POR' = porcelain : WW = wirewound
tubes and transistors MEG = meg =106 POS' = position(s) wiO0 = without
selected for best M = milli =10-3 POLY = polystyrene
performance will be MINAT = minature POT = potentiometer
supplied if ordered METFLM = metal film * = optimum value
by @stock numbers. MFR = manufacturer RECT = rectifier selected at factory,
MOM = mounting = rotary average value
ELECT = electrolytic MTG = momentary RMS = root-mean-square shown (part may
ENCAP = encapsulated MY = mylar RMO = rack mount only be omitted)