Panasonic TH-80LFB70U Operating Instructions Manual page 75

Item
Locks the input switch operation.
Off
LINK
*1 "SLOT INPUT" is displayed when an optional Terminal Board is installed.
*2 "COMPONENT" may be displayed as "RGB" depending on the setting of "Component/RGB-in select".
Input lock
Notes:
• Only the adjusted signal is displayed (see page 20).
• Input switch can be used when this is set to "Off". Two screen display cannot be selected.
• In two screen display mode, if anything other than "Off" is set, the value will be ¿ xed as the value input
in the single screen display mode.
Off
Off: All the buttons on main unit can be used.
MENU&ENTER: Locks
On: Locks all the button on main unit except the Power switch.
Button lock
Sets Button lock with the unit buttons in the following procedure.
Off: Press
MENU&ENTER: Press
On: Press
Off
Off: You can use all of the buttons on the remote control.
User1: You can only use
Remocon User level
User2: You can only use
User3: Locks all the buttons on remote control.
Enable: Enables the "Off-timer function".
Disable: Disables the "Off-timer function".
Off-timer function
Note: When "Disable" is set, the Off-timer is cancelled.
Normal
Sets the power mode of the unit for when the power recovers from failure or after plugging off and in again.
Normal: Power returns in as the same state as before the power interruption.
Initial Power Mode
Standby: Power returns in standby mode. (Power Indicator : red/orange)
On:
Note: When using multiple displays, "Standby" is preferred to be set in order to reduce a power load.
Sets panel ID number when panel is used in "Serial ID".
Set value range: 0 - 100
ID select
(Standard value: 0)
Sets the panel ID Control.
Off: Disables external control by the ID.
Serial ID
On: Enables the external control by the ID.
Adjusts the image display size on screen.
Off: Sets the normal image display size on screen.
On: Sets the image display size approximately 95 % of the normal image display.
Notes:
Display size
• This setting is valid only when the input signals are as follows;
NTSC, PAL, SECAM, M.NTSC, PAL60, PAL-M, PAL-N (Video)
525i, 525p, 625i, 625p, 750/60p, 750/50p, 1125/60i, 1125/50i, 1125/24psF, 1125/25p, 1125/24p,
1125/30p, 1125/60p, 1125/50p, 1250/50i (Component Video, RGB, DVI, SDI, HDMI)
• This setting is invalid when digital zoom is selected.
• When "Display size" is set to "On", "H-Pos" and "V-Pos" in "Pos./Size" can be adjusted.
• Refer to each board's operating instruction for DVI, SDI, HDMI's corresponding signals.
HDMI1 HDMI2 SLOT INPUT*
Miracast(TM)
When a Terminal Board with dual input terminals is installed, "SLOT INPUT A" and "SLOT INPUT B"
are displayed.
(see page 68)
MENU&ENTER
MENU
four times Press
+
/
four times Press
-
/
User1 User2
,
button on the remote control.
Standby
Power returns in power On. (Power Indicator : green)
Off
Adjustments
1
VIDEO
Panasonic APPLICATION
On
and buttons on main unit.
four times Press
INPUT
four times Press + four times Press
/
four times Press
User3
, , , buttons on the remote control.
On
On
Options Adjustments
2
COMPONENT* PC
MEMORY VIEWER
-
four times Press
/
four times Press
INPUT
four times Press
+
/
DVI DIGITAL
WHITEBOARD
73