Panasonic TH-80LFB70U Operating Instructions Manual page 76

Options Adjustments
Item
Off: Nullify all the settings adjusted.
On: Sets the colour temperature for TV studio.
Studio W/B
Note: Valid only when the "Warm" is set as "White balance" in Picture menu.
Sharpens the contrast for a better view when a part of the image is too light to see.
Off: Disables "Studio Gain".
On: Enables "Studio Gain".
Studio Gain
Note: This setting is valid only when the input signals are as follows:
Select the LAN control protocol.
LAN Control
Protocol 1: Control with the Panasonic Display sequence.
Protocol
Protocol 2: Control with the sequence that compatible with Panasonic Projector.
RS-232C/LAN
Set up the informing manner if error warning occured. (see page 79)
Information Timing
Off
Off:
Auto: Power is transmitted to the slot power only when main power is on.
Slot power
On:
Note: In some cases, power is transmitted to the slot power when main power is on or in the standby
Off
You can set the power-on delay time of the displays to reduce the power load, when you press
turn on the multiple displays that are set together.
Set each display's setting individually.
Off:
1 to 30 (sec.): Set the power-on delay time (second).
Power On Screen
Notes:
Delay
• During this function is working, the power indicator is blinking green.
• This function also works when the power recovers from failure or after plugging off and in again the
power cord.
After you unplug and plug the power cord in while the unit is in standby mode and also the power is
being supplied to a terminal board, the unit will start supplying the power to the board with time delay
according to the setting.
The power indicator lights up red ¿ rst and it turns orange when the power starts being supplied to the
board.
Sets the operational mode of "DVI-D Power management".
DVI Power
Standard mode: Activates power management when synchronization signals are not detected.
management mode
Low power mode: Activates power management also when +5V DC in DVI-D IN terminal is not detected.
Off: Not display the clock.
On: Display the clock.
The clock is displayed at the lower left of the screen when
Clock Display
Sets All Aspect mode (advanced aspect setting) or default aspect mode.
With each press of
Off: Default aspect mode
On: All Aspect mode
Aspect mode of each setting is as follows:
(Example: HD signal)
All Aspect
Off For TH-80LFB70U
On 4:3 (1) 4:3 (2) 4:3 Full Zoom1 Zoom2 Zoom3 16:9 14:9 Just1 Just2
Sets the operational mode of the automatic position adjustment in the Pos./Size menu.
Manual: Automatic position adjustment starts when
Auto Setup
Auto:
74
Component Video, RGB (analog), SDI, HDMI
Auto On
Power is not transmitted to the slot power.
Power is transmitted to the slot power when main power is on or in the standby state.
state regardless of the slot power setting.
1 2 3.... 30
The display will be turned on at the same time as
After pressing
setting.
Note: When "Day/Time Settings" is not set, the clock is not displayed even if
"Clock Display" is "On". (see page 58)
10:00
button, the aspect changes in the selected mode.
4:3 H-FILL ZOOM FULL JUST
For TH-80LFB70E, TH-80LFB70W
4:3 4:3 Full Zoom1 Zoom2 Zoom3 16:9 14:9 Just
position adjustment is executed from the Pos./Size menu.
Other than remote control or menu operation, automatic position adjustment starts:
When the display power is turned ON.
When the input signal is switched.
Adjustments
, the display will be powered on with time delay depending on this
is pressed on the remote control or automatic
is pressed.
button is pressed.
to