Specifications; Standard Specifications - Panasonic KT4H User Manual

13. Specifications

13.1 Standard specifications

Mounting
Setting
Display PV display
SV display
MEMO display : 11-segment backlight LCD Green, character size 4.8 x 2.8mm (H x W)
Action indicators
Accuracy (Setting and Indication):
Thermocouple : Within
RTD
DC current
DC voltage
Input sampling period
Input Thermocouple : K, J, R, S, B, E, T, N, PL- , C (W/Re5-26)
RTD
DC current
DC voltage
Control output (OUT1)
Relay contact : 1a, Control capacity
Non-contact voltage (For SSR drive): 12V DC 15%, Maximum 40mA (short circuit protected)
DC current
Alarm 1 output
Action
Hysteresis
Output
Control action
PID action (with auto-tuning function)
PI action: When derivative time is set to 0
PD action (with auto-reset function): When integral time is set to 0
P action (with auto-reset function): When derivative and integral time are set to 0.
ON/OFF action: When proportional band is set to 0 or 0.0
OUT1 proportional band : 0 to 1000
: Flush
: Input system using membrane sheet key
: 11-segment backlight LCD Red/Green/Orange, character size 12.0 x 5.4mm (H x W)
: 11-segment backlight LCD Green, character size 6.0 x 3.5mm (H x W)
: Backlight Orange
0.2% of each input span 1digit, or within
whichever is greater
However R, S inputs, 0 to 200
B input, 0 to 300 (600 ): Accuracy is not guaranteed
K, J, E, T, N inputs, less than 0
: Within 0.1% of each input span 1digit, or within
whichever is greater
: Within 0.2% of each input span 1digit
: Within 0.2% of each input span 1digit
: 0.25 seconds
External resistance, 100
(However, B input: External resistance, 40
: Pt100, JPt100, 3-wire system
Allowable input lead wire resistance (10
: 0 to 20mA DC, 4 to 20mA DC
Input impedance: 50
Allowable input current, 50mA or less [When 50
: 0 to 1V DC Input impedance (1M
Allowable input voltage (5V DC or less)
Allowable signal source resistance (2k
: 0 to 5V DC, 1 to 5V DC, 0 to 10V DC Input impedance (100k
Allowable input voltage (15V DC or less)
Allowable signal source resistance (100
Electrical life, 100,000 cycles
: 4 to 20mA DC, Load resistance, Maximum 550
: ON/OFF action
: 0.1 to 100.0 ( ), or 1 to 1000 (Default: 1.0 )
: Relay contact 1a
Control capacity, 3A 250V AC (resistive load) Electrical life, 100,000 cycles
(2000 ), 0.0 to 1000.0
(ON/OFF action when set to 0 or 0.0) (Default: 10 )
(0 to 400 ): Within
(32 ): Within
or less
or less)
or less per wire)
[50 shunt resistor (sold separately) must be
connected between input terminals.]
separately) is used]
or more)
or less)
or less)
3A 250V AC (resistive load)
1A 250V AC (inductive load cosø=0.4)
( ) or 0.0 to 100.0%
57
2 (4 ),
6 (12 )
0.4% of input span 1digit
1 (2 ),
shunt resistor (sold
or more)