Slope Operation - Toro 25450W Operator's Manual

•
Before operating the machine with an attachment, ensure
that the attachment is properly installed.
•
Use extra care when handling fuels. They are flammable
and vapors are explosive.
– Use only an approved container.
– Do not remove the fuel cap or add fuel with the
engine running. Allow the engine to cool before
fueling. Do not smoke near the machine while the
engine is running.
– Do not refuel or drain the machine indoors.
•
Check that the operator's presence controls, safety
switches, and shields are attached and functioning
properly. Do not operate the machine unless these
controls, switches, and shields are functioning properly.
General Operation
•
Always wear the seat belt when operating this machine.
•
Do not run the engine in an enclosed area.
•
Do not operate the machine without all of the guards
and panels securely in place. Ensure that all interlocks are
attached, adjusted correctly, and functioning properly.
•
Decrease the ground speed of the machine and use
caution when making turns and crossing roads and rough
or uneven terrain.
•
Do not operate the machine while under the influence
of alcohol or drugs.
•
Ensure that the area is clear of other people before
operating the machine. Stop the machine if anyone enters
the area.
•
Excessive vibration from a trencher or a plow can cause a
trench, an overhang, or a high bank to collapse, resulting
in possible injury or death.
•
If your view of the work area is not clear, always have a
signal person direct the movement of the machine.
•
Do not leave a running machine unattended. Stop the
engine and remove the key whenever you leave the
machine.
•
Use only Toro-approved attachments. Attachments can
change the stability and the operating characteristics of
the machine.
•
Watch for traffic when operating the machine near or
across roadways.
•
Only operate the machine in areas where there are no
obstacles in close proximity to you. Failure to maintain
an adequate distance from trees, walls, and other barriers
while operating the machine may result in injury and/or
damage. Operate the machine only in areas where there
is sufficient clearance for you to safely maneuver the
machine.
•
Locate the pinch point areas that are marked on the
machine and attachments; keep hands and feet away from
these areas.
•
Lightning can cause severe injury or death. If lightning
is seen or thunder is heard in the area, do not operate
the machine; seek shelter.

Slope Operation

•
Avoid operating this machine on slopes, if possible.
•
Keep all movements on slopes slow and gradual. Do not
make sudden changes in speed or direction.
•
Avoid starting or stopping the machine on a slope. If the
machine loses traction, keep the heavy end of the machine
uphill and proceed slowly, straight down the slope.
•
Avoid turning the machine on slopes. If you must turn,
turn slowly and keep the heavy end of the machine uphill.
•
Do not operate the machine near drop-offs, ditches, or
embankments. The machine could suddenly turn over if
a tire or track goes over the edge of a cliff or ditch, or if
an edge caves in.
Rollover Protection Structure (ROPS)
System
•
Before operating the machine, ensure that the seat belt is
in good condition and is securely attached to the machine.
•
Inspect the ROPS at the interval recommended in this
manual or when the ROPS has been in an accident.
•
Replace a damaged ROPS using only genuine Toro
replacement parts; do not repair or modify the ROPS.
•
Check carefully for overhead clearances (i.e. branches,
doorways, electrical wires) before driving under any
objects, and do not contact them.
•
Do not remove the ROPS except when replacing it.
•
Do not add weight to the machine that exceeds the gross
weight displayed on the ROPS label.
Transporting Safety
When you transport the machine to or from the job site,
observe the following safety precautions:
•
Do not carry passengers on the machine.
•
Keep all bystanders away while you are moving the
machine.
•
Use care when loading or unloading the machine into a
trailer or truck.
•
Watch for traffic when you are crossing roadways with
the machine.
•
Check for overhead clearances (i.e., branches, doorways,
electrical wires) before driving under any objects, and do
not contact them.
5