Toshiba strata DK8 Installation Instructions Manual page 252

Hide thumbs Also See for strata DK8:
Table of Contents

Advertisement

PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM
RECORDS
SECTION 100-816-302
MARCH 1993
of these
slots is capable
of supporting
any of
the
following
PCBs:
PDKU,
PEKU,
PSTU,
PESU, PIOU, PIOUS,
KCDU.
It is important
to
note that Slots 04 and 05 are 16 channel
slots
that are capable
of supporting
Off-hook
Call
Announce
(OCA)
and
Data
Interface
Units
(DIUs),
whereas
Slots 06 and
07 are eight
channel
slots that cannot support
OCA or DIUs.
Therefore,
we recommend
that you install the
station PCB in either Slot 04 or 05 rather than 06
or 07. The Expansion
Unit can support
a maxi-
mum of eight station
ports and four CO lines.
signed to logical ports with
Program
04. Station
number
assignment
is fully flexible so that each
station can have any intercom
number
assigned
uptofourdigits.
However,
ifthefirstdigitisnot
1 or 2, access code conflicts may exist,
and
a new system
numbering
plan will have to be
carefully
worked
out-If
desired,
a digital tele-
phone accompanying
a DDSS console (STRATA
DK16 only) or Add-on
module
(DK8 and DK16)
can have
a station
number
of 0 or 01, etc.
without
conflict.
IMPORTANT NOTE!
After completing
Program 03, turn the
system power off for five seconds and
then turn itbackon. This willset in memory
all of the configuration data entered in this
program.
Program 00-Software
Check/Remote Mainte-
nance Security
Code
Assignments:
The RAM
checksum,
the KPSU
Power
Cycle
Counter,
and the system software
version can be verified
with this program.
Neither
of these
attributes
can be changed
or edited
with this program.
Program
00, though,
does allow two security
codes to be set for Remote
Maintenance:
l
Level 1 Security
Code-Remote
Mainte-
nance security code which allows entry to all
programs
and data.
l
Level 2 Security
Code-Remote
Mainte-
nance security
code which allows
entry to
Programs
30 - 39 and 77 - 89.
Program 04-Logical
Port/Intercom
Number
Assignment:
Initialized
station
intercom
num-
bers are 10 - 19 (STRATA
DK8) or 10 - 29
(STRATA
DK16), which are assigned
to logical
ports 00 - 09 (STRATA DK8) or 00 - 19 (STRATA
DK16), respectively.
This program
can be used
to change
this initialized
setting.
The standard
station intercom
numbers
10
- 19 (STRATA
DK8), 10 - 29 (STRATA
DK16)
can
be reassigned
to different
logical
port
numbers
with
Program
04; or the station inter-
com numbers
can first be changed
to numbers
other than
10 - 19 (STRATA
DK8),
10 - 29
(STRATA
DK16)
with
Program
05, then
as-
All user guides are written
using the stan-
dard access codes and station
numbers.
If no
assignment
is made in
Program 04,
the system
when powered
up will automatically
assign sta-
tion numbers
as follows:
l
For STRATA
DK8: The system
automati-
cally assigns station numbers
10 - 13 to the
digital telephone
circuit ports in the KSU,
station numbers
14 - 15 to the first optional
CO Line/Digital
Telephone
Interface
Unit
(QCDU)
PCB (even
if it is not installed),
station
numbers
16 - 17 to the second
optional
(QCDU)
PCB (even if it is not in-
stalled),
and station numbers
18 - 19 to the
optional
Standard
Telephone
Interface
Unit
(QSTU)
PCB (even if it is not installed).
l
For STRATA
DK16: The system
automati-
cally assigns station numbers
10 - 17 to the
digital
telephone
circuit ports in the Base
Unit, station numbers
18 - 21 to the optional
Base
Unit Standard
Telephone
Interface
Unit (KSTU) PCB (even if it is not installed),
and station numbers
22 - 29 to the optional
Expansion
Unit (even if it is not installed).
Program
04 does not apply to the door phone
standard
numbering
scheme
(551
- 556 for
STRATA
DK8 and DK16), the internal
modem
(IMDU) number
(619) (for STRATA
DKI 6 only),
or the Direct
Inward
System
Access
(DISA)
class of service port (Port 10 for STRATA
DK8,
Port 20 for STRATA
DK16). The system
auto-
matically assigns door phone station numbers
if
a door phone
is specified
in
Program 77-1.
Programs 01 &02-Logical
and Physical Sta-
tion Port Display:
Logical
and physical
ports
can both be displayed
with
Program 01
or 02.
Logical ports cannot
be relocated
with either of
these two programs.
2-2

Advertisement

Table of Contents
loading

This manual is also suitable for:

Strata dk16

Table of Contents