Siemens SINUMERIK 840D SL Operating Manual page 14
Hide thumbs
Also See for SINUMERIK 840D SL:
- Function manual (2184 pages) ,
- Programming manual (1334 pages) ,
- Commissioning manual (1102 pages)
Table of Contents
Advertisement
Table of contents
8.1.4
Reaming (CYCLE85) ................................................................................................................ 290
8.1.4.1
Function..................................................................................................................................... 290
8.1.5
Deep-hole drilling (CYCLE83)................................................................................................... 292
8.1.5.1
Function..................................................................................................................................... 292
8.1.6
Boring (CYCLE86) .................................................................................................................... 295
8.1.6.1
Function..................................................................................................................................... 295
8.1.7
Tapping (CYCLE84, 840).......................................................................................................... 297
8.1.7.1
Function..................................................................................................................................... 297
8.1.8
Drill and thread milling (CYCLE78) ........................................................................................... 303
8.1.8.1
Function..................................................................................................................................... 303
8.1.9
Positioning and position patterns .............................................................................................. 307
8.1.10
Arbitrary positions (CYCLE802)................................................................................................ 309
8.1.11
Position pattern line (HOLES1), grid or frame (CYCLE801)..................................................... 312
8.1.12
Circle position pattern (HOLES2).............................................................................................. 314
8.1.13
Displaying and hiding positions................................................................................................. 316
8.1.14
Repeating positions................................................................................................................... 317
8.2
Milling ........................................................................................................................................ 319
8.2.1
Face milling (CYCLE61)............................................................................................................ 319
8.2.1.1
Function..................................................................................................................................... 319
8.2.2
Rectangular pocket (POCKET3)............................................................................................... 322
8.2.3
Circular pocket (POCKET4) ...................................................................................................... 325
8.2.4
Rectangular spigot (CYCLE76)................................................................................................. 330
8.2.5
Circular spigot (CYCLE77)........................................................................................................ 333
8.2.5.1
Function..................................................................................................................................... 333
8.2.6
Multi-edge (CYCLE79) .............................................................................................................. 335
8.2.6.1
Function..................................................................................................................................... 335
8.2.7
Longitudinal groove (SLOT1) .................................................................................................... 338
8.2.8
Circumferential groove (SLOT2) ............................................................................................... 341
8.2.9
Open groove (CYCLE899) ........................................................................................................ 344
8.2.10
Long hole (LONGHOLE) - only for G code programs............................................................... 351
8.2.11
Thread milling (CYCLE70) ........................................................................................................ 353
8.2.12
Engraving (CYCLE60)............................................................................................................... 357
8.3
Contour milling .......................................................................................................................... 363
8.3.1
General...................................................................................................................................... 363
8.3.2
Representation of the contour................................................................................................... 363
8.3.3
Creating a new contour ............................................................................................................. 365
8.3.4
Creating contour elements ........................................................................................................ 367
8.3.5
Changing the contour................................................................................................................ 372
8.3.6
Contour call (CYCLE62) - only for G code program ................................................................. 373
8.3.7
Path milling (CYCLE72) ............................................................................................................ 374
8.3.8
Contour pocket/contour spigot (CYCLE63/64).......................................................................... 378
8.3.9
Predrilling contour pocket (CYCLE64) ...................................................................................... 380
8.3.10
Milling contour pocket (CYCLE63)............................................................................................ 383
8.3.11
Residual material contour pocket (CYCLE63) .......................................................................... 385
8.3.12
Milling contour spigot (CYCLE63)............................................................................................. 387
8.3.13
Residual material contour spigot (CYCLE63) ........................................................................... 389
8.4
Turning - only for G code programs .......................................................................................... 392
8.4.1
General...................................................................................................................................... 392
8.4.2
Stock removal (CYCLE951) ...................................................................................................... 392
8.4.3
Groove (CYCLE930) ................................................................................................................. 395
8.4.4
Undercut form E and F (CYCLE940) ........................................................................................ 398
14
Operating Manual, 02/2012, 6FC5398-7CP40-3BA0
Milling
Advertisement
Table of Contents
