Setting The Preset 1, 2, And 3 Buttons - Toro ProPass 200 Operator's Manual

indicating that the remote is in a set-only mode. In
this set-only mode, you can adjust either setting up
or down, but the floor and option do not activate,
remaining off. This allows you to set the desired
speeds or use the stored settings without causing
unwanted movement. After setting the speeds, press
the A S button to activate the floor and option
LL TART
at the chosen setting (if the hydraulics are engaged,
the floor and option will start). Press A
time to store the current value in memory.
Note:
Changes to the settings while the floor and
option are running are immediately effective, but they
are temporary unless you store the new setting by
pressing A S again after changing the setting.
LL TART
For instance, you make an adjustment while the
display shows FLRS and OPTS, press A
starting the floor and option at the adjusted setting,
and then turn the remote off without pressing A
S again, storing the change. The next time
TART
you use the remote, the settings will revert to the
previously stored values.
Note:
A 10 second timer starts when you press A
S and set-only mode displays. If you do not press
TART
a button during the 10 second interval, the display
reverts to FLR and OPT and the previous state/value
displays and is enforced. The timer resets to ten
seconds if any button is pressed while the remote is
in the set-only.
1. Press the A S
LL TART
The preview values and FLRS and OPTS
display.
2. Adjust the speed settings as follows:
•
Adjust the floor speed setting using the using
the I
NCREASE
D F
ECREASE LOOR
•
Adjust the option speed setting using the
using the I
NCREASE
the D
ECREASE
3. Press the A S
LL TART
option.
S
LL TART
S
LL
button.
F S button or the
LOOR PEED
S button.
PEED
or
O S button or
PTION PEED
O S button.
PTION PEED
or
button to run the floor and
4. Press the A
a third
The display shows ALL STORE. The set value
will be used whenever the option is started in
the future until you change the setting again.
Note:
to store the settings using the A
If only 1 or neither is running, pressing the A
TART
S
TART
the one that was not running. Nothing is stored
LL
and the commands previewed are the previously
stored floor and the option settings.
It is important to realize that the stored command
for the floor and option are used twice, once in
LL the event of an individual command using the
F
LOOR
once in the event of a combined action using
A S
LL
Setting the Preset 1, 2, and
3 Buttons
The remote has 3 P
program with floor and option speed settings. Each
P button acts like a preview mode for the A
RESET
S button, except that they use different, user
TART
defined quick reference speed values.
If the floor and/or the option happen to be running at
the time you press a P
of both floor and option settings is displayed; if you
then press the A
values are replaced by the preset values. If you do
not press the A
system will revert back to the previously stored values.
Use the following procedure to set the values of a
P button:
RESET
1. Start both the floor and option either individually
or by using the A
2. Set the desired speeds of both floor and
option by using the appropriate I
D
ECREASE
3. Press and hold the S
the desired P
33
S button to store the values.
LL TART
Both the floor and option must be running
button will either start them both or start
S or O S
TART PTION TART
; in either case, it is the same number.
TART
buttons which you can
RESET
button, a preview value
RESET
S button, the current operating
LL TART
-S button within 10 seconds, the
LL TART
S button .
LL TART
speed buttons for each output.
button and then press
TORE
button (1, 2, or 3).
RESET
S button.
LL TART
LL
buttons, and
LL
and
NCREASE