Toro Mower Safety - Toro Greensmaster TriFlex 3420 Operator's Manual

•
Keep the ROPS in safe operating condition by
periodically thoroughly inspecting for damage and
keeping all mounting fasteners tight.
•
Replace a damaged ROPS. Do not repair or
revise.
•
Do not remove the ROPS.
•
Any alterations to a ROPS must be approved by
the manufacturer.
Maintenance and Storage
•
Park the machine on level ground, disengage the
drives, lower the cutting units, set the parking
brake, stop the engine, remove the key, and
disconnect spark plug wire(s). Wait for all
movement to stop before adjusting, cleaning, or
repairing the machine.
•
Clean grass and debris from cutting units, drives,
mufflers, and the engine to help prevent fires.
Clean up oil or fuel spills.
•
Let the engine cool before storing and do not store
the machine near flames.
•
Shut off the fuel while storing or transporting the
machine. Do not store fuel near flames or drain
the fuel tank indoors.
•
Never allow untrained personnel to service the
machine.
•
Use jack stands to support components when
required.
•
Carefully release pressure from components with
stored energy.
•
Disconnect the battery and remove the spark plug
wire(s) before making any repairs. Disconnect
the negative terminal first and the positive last.
Connect the positive terminal first and the negative
terminal last.
•
Use care and wear gloves when checking the
reels.
•
Keep hands and feet away from moving parts. If
possible, do not make adjustments with the engine
running.
•
Charge batteries in an open, well-ventilated area,
away from spark and flames. Unplug the charger
before connecting or disconnecting it from the
battery. Wear protective clothing and use insulated
tools.
•
Keep all parts in good working condition and all
hardware and hydraulic fittings tightened. Replace
all worn or damaged decals.

Toro Mower Safety

The following list contains safety information specific
to Toro products or other safety information that you
must know that is not included in the ANSI standards.
This product is capable of amputating hands and
feet and of throwing objects. Always follow all safety
instructions to avoid serious injury or death.
Use of this product for purposes other than its intended
use could prove dangerous to user and bystanders.
Operation
•
Know how to stop the engine quickly.
•
Check the safety interlock switches daily for proper
operation.
•
Before attempting to start the engine, disengage
all blade attachment clutches, shift into neutral,
and engage the parking brake.
•
Using the machine demands attention. To prevent
loss of control:
– Do not drive close to sand traps, ditches,
creeks, or other hazards.
– Reduce speed when making sharp turns.
Avoid sudden stops and starts.
– This machine is not designed or equipped for
on-road use and is a "slow-moving vehicle."
If you must cross or travel on a public road,
you should be aware of and comply with
local regulations, such as required lights,
slow-moving vehicle signs, and reflectors.
– Watch out for traffic when near or crossing
roads. Always yield the right-of-way.
– Apply the service brakes when going downhill
to keep forward speed slow and to maintain
control of the machine.
•
The grass baskets must be in place during
operation of the reels or thatchers for maximum
safety. Shut the engine off before emptying the
baskets.
•
Raise the cutting units when driving from 1 work
area to another.
•
Do not touch the engine, muffler, or exhaust pipe
while the engine is running or soon after it has
stopped because these areas could be hot enough
to cause burns.
•
Stay clear of the rotating screen at the side of the
engine to prevent direct contact with your body
or clothing.
•
If a cutting unit strikes a solid object or vibrates
abnormally, stop immediately, turn the engine off,
wait for all motion to stop, and inspect the machine
for damage. Repair or replace a damaged reel or
bedknife before continuing operation.
•
Before getting off the seat, move the functional
control lever to N
and wait for the reels to stop spinning. Set the
parking brake. Stop the engine and remove the
key from the ignition switch.
5
, raise the cutting units,
EUTRAL